Hi nuclear2016,
Welcome to the 10forums :)
The error 0x124 WHEA_UNCORRECTABLE_ERROR (Windows Hardware Error Architecture) means that there are problems with your hardware, but this error is also caused by overclocking, faulty drivers, overheating, improper seating or BIOS problems.
The error is reported on the L2 cache of the CPU, the differences in cores is remarkeable.
This could indicate a possible faulty CPU, but I would recommend that you run the tests to verify and ensure nothing else is faulty.
Code:
===============================================================================
Section 2 : x86/x64 MCA
-------------------------------------------------------------------------------
Descriptor @ ffffe00005a00138
Section @ ffffe00005a002c0
Offset : 664
Length : 264
Flags : 0x00000000
Severity : Fatal
Error : GCACHEL2_ERR_ERR (Proc 16 Bank 17)
Status : 0xbe200000000b110a
Address : 0x0000000130300040
Misc. : 0x50fe201095000086
===============================================================================
Section 2 : x86/x64 MCA
-------------------------------------------------------------------------------
Descriptor @ ffffe00043400138
Section @ ffffe000434002c0
Offset : 664
Length : 264
Flags : 0x00000000
Severity : Fatal
Error : GCACHEL2_ERR_ERR (Proc 19 Bank 17)
Status : 0xbe200000000b110a
Address : 0x00000002b04a9c40
Misc. : 0x40fe20508119c086
===============================================================================
Section 2 : x86/x64 MCA
-------------------------------------------------------------------------------
Descriptor @ ffffe0003cc21138
Section @ ffffe0003cc212c0
Offset : 664
Length : 264
Flags : 0x00000000
Severity : Fatal
Error : GCACHEL2_ERR_ERR (Proc 37 Bank 17)
Status : 0xbe200000000b110a
Address : 0x000000012e079c00
Misc. : 0x40fe2010931a4086
STOP 0x124 Troubleshooting
Read carefully before proceeding.
Warning
If you're overclocking your system, revert back to stock clocks now.
Note
Test the system once the overclock is removed before continuing with the steps outlined below.
Part One: CPU Stress Test
Part Two: MemTest86+ RAM Diagnostic
Part Three: Hard Drive Diagnostics
Part Four: GPU Stress Test
Run Prime95 and/or IntelBurnTest to stress test your CPU. Prime95 - Stress Test Your CPU - Windows 10 Forums & CPU - Stress Test Using IntelBurnTest - Windows 7 Help Forums
Warning
Your CPU temperatures will rise quickly while under this stress test. Keep a keen eye on them and abort the test if overheating occurs.
Make a photo of the result and post it.
Run MemTest86+ to analyse your RAM. MemTest86+ - Test RAM - Windows 10 Forums
Note
MemTest86+ needs to be run for
at least 8 complete passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for
zero errors here. Even a single error will indicate RAM failure.
Make a photo of the result and post it please.
Addition:
If errors show up you can stop the test, remove all sticks but 1 and test this single stick in each slot for 8 passes or until errors show, switch sticks and repeat.
If errors show up and you see them a lot later, no problem, the errors don't affect the test.
Run SeaTools to check the integrity of your HDD. SeaTools for DOS and Windows - How to Use - Windows 7 Help Forums
Run following tests
- Short Drive Self Test
- Short generic
- Long generic
If the short generic fails, no need for the long generic.
Note
Do not run SeaTools on an SSD as the results will be invalid.
Post screenshots/photos of the test results
Run chkdsk
Disk Check - Windows 7 Help Forums
Upload the chkdsk log Chkdsk Log in Event Viewer - Read in Windows 10 - Windows 10 Forums
Run HDTune to
- scan for errors, no quick scan but full scan
- check the health,
- benchmark.
It may take some time, but please take the time you need to perform it properly.
When above is done please make screenshots of the following
- the error scan,
- the health,
- the benchmark incl. following
- transfer rate,
- access time,
- burst rate,
- cpu usage.
Run Furmark to stress test your GPU. FurMark - GPU Stress Test - Windows 10 Forums
Note
Run Furmark for around 30 minutes.
Warning
Your GPU temperatures will rise quickly while Furmark is running. Keep a keen eye on them and abort the test if overheating occurs.
Make a photo of the result and post it.
Please fill in your system specsPlease follow
this tutorial and download the tool. The tool will give you detailed information about your system specs, please fill in your system specs more completely including PSU, cooling and other used stuff like mouse, keyboard, monitor, case, etc.
The PSU, cooling and other stuff are NOT mentioned in the tool.
How to fill in your system specs: