After 3 months since KB5034441 was released, it still won't install

Page 8 of 9 FirstFirst ... 6789 LastLast

  1. Pentagon
    Posts : 697
    WIN 10 19045.4291
       New #71

    OK, everything looks good!

    I have learned s.th. new.
    In a mixed environment with MBR and GPT disks the Bootmanager doesn't count the partitions before the EFI partition. That why I thought you boot from disk 0.
    Harddiskvolume2 is on disk 4 and not disk 0

    Thank you & have a nice day
      My Computer
    Quote Quote

  3. JS racer
    Posts : 16
    win 10
       New #72

    Pentagon said:
    OK, everything looks good!

    I have learned s.th. new.
    In a mixed environment with MBR and GPT disks the Bootmanager doesn't count the partitions before the EFI partition. That why I thought you boot from disk 0.
    Harddiskvolume2 is on disk 4 and not disk 0

    Thank you & have a nice day
    got ya.... you too.. thanks so much for your help, and thanks for your efforts with everyone else getting that update to work...
    we all greatly appreciate it !!
      My Computer
    Quote Quote

  4. Zizzy
    Posts : 2
    Windows 10
       New #73

    @Pentagon

    I've followed all of your cmd steps, when I get to the end and try to enable reagentc, I get an error saying:

    Windows RE cannot be enabled on a volume with BitLocker Drive Encryption enabled. This is a fresh Windows install so I'm not even sure how to proceed.
      My Computer
    Quote Quote

  6. Pentagon
    Posts : 697
    WIN 10 19045.4291
       New #74

    Zizzy said:
    @Pentagon

    Windows RE cannot be enabled on a volume with BitLocker Drive Encryption enabled.
    This is a fresh Windows install so I'm not even sure how to proceed.
    What does this message mean? Do what? Disable what?
      My Computer
    Quote Quote

  7. Zizzy
    Posts : 2
    Windows 10
       New #75

    Pentagon said:
    What does this message mean? Do what? Disable what?
    This is what command prompt shows when I try to run "reagentc /enable" at the end of your list
      My Computer
    Quote Quote

  8. Bree
    Posts : 31,700
    10 Home x64 (22H2) (10 Pro on 2nd pc)
       New #76

    Zizzy said:
    ...when I get to the end and try to enable reagentc, I get an error saying:

    Windows RE cannot be enabled on a volume with BitLocker Drive Encryption enabled. This is a fresh Windows install so I'm not even sure how to proceed.
    Welcome to Ten Forums.

    This error may be seen if the recovery partition is still too small. Assuming that is not the case, use diskpart to check the ID of your recovery partition, resetting it if necessary. In Diskpart select the recovery partition and use the command detail partition.For MBR it should be 27, for GPT it's DE94BBA4-06D1-4D40-A16A-BFD50179D6AC. To reset a partition ID use the Setid command.
    After 3 months since KB5034441 was released, it still won't install-image.png


    ... I got an error:
    REAGENTC.EXE: Windows RE cannot be enabled on a volume with BitLocker Drive Encryption enabled.

    ... as it couldnt find a suitable partition. In the log (C:\Windows\Logs\ReAgent\ReAgent.log) I could see:

    failed to find target partition: 0x2

    Using diskpart (selecting the correct partition) I was able to fix the issue using:

    set id=27
    KB5034441 Security Update for Windows 10 (21H2 and 22H2) - Jan. 9 - post #40

    Windows Recovery Environment....
    This partition must use the Type ID: DE94BBA4-06D1-4D40-A16A-BFD50179D6AC
    https://learn.microsoft.com/en-us/wi...ools-partition
      My Computers
    Quote Quote

  9. Pentagon
    Posts : 697
    WIN 10 19045.4291
       New #77

    This is definitely not an id-problem.
    The message says that it is impossible when bitlocker is enabled.
      My Computer
    Quote Quote

  10. Bree
    Posts : 31,700
    10 Home x64 (22H2) (10 Pro on 2nd pc)
       New #78

    Pentagon said:
    This is definitely not an id-problem.
    The message says that it is impossible when bitlocker is enabled.
    It still could be an ID problem, it certainly was in the example I quoted. The ID was incorrect, so reagentc /enable couldn't find a suitable recovery partition. In that case it's fall-back position is to put the recovery environment in C:\Recovery\WindowsRE instead - which of course it could not do if C: is bitlocker encrypted.
    After 3 months since KB5034441 was released, it still won't install-image.png
      My Computers
    Quote Quote

  12. Pentagon
    Posts : 697
    WIN 10 19045.4291
       New #79

    I would bet 1000 $

    With some background knowledge you can configure a reliable Recovery Environment without a single reagentc-command!
    But when Zizzy can't interpretate the message, I can't help.
      My Computer
    Quote Quote

  13. Nikol
    Posts : 2
    Windows10
       New #80

    Pentagon said:
    @benherrmann
    Your problem is not easy - it's very easy and not a single 3rd-party tool is needed!
    You only have to know how to run "Command Prompt" as Administrator.
    when you see this:
    C:\WINDOWS\system32>
    you are on the right way.

    Then copy the following commands and paste into command prompt:
    step by step
    reagentc /disable
    diskpart
    sel disk 0
    sel par 5
    delete partition override
    sel par 4
    extend
    shrink minimum=1024
    create partition primary
    format quick fs=ntfs label="Recovery"
    set id="de94bba4-06d1-4d40-a16a-bfd50179d6ac"
    gpt attributes=0x8000000000000001
    exit
    reagentc /enable

    The update will be installed successfully!

    Hello Master,

    I am getting an error while entering the last commands, can you please help me? Thank you

    OLD: https://i.imgur.com/pgHUg2D.png
    NEW: https://i.imgur.com/xOCym5H.png
    Commands: https://pastebin.com/raw/csPrc6mr

    set id="de94bba4-06d1-4d40-a16a-bfd50179d6ac"
    gpt attributes=0x8000000000000001

    I can't enter these two commands :-/


    EDIT:
    OK, it was enough just to enter the change to ID 27 for MBR, @Bree thank you
    https://i.imgur.com/wTz5UUs.png

    WORK: https://i.imgur.com/icSjemY.png
    Last edited by Nikol; 1 Week Ago at 05:32.
      My Computer
    Quote Quote

 

  Related Discussions
KB5034441 rabbit hole
in Windows Updates and Activation

I have a recent clean install of 10P on MBR with the basic partitions: 1)system, 2)OS, 3)recovery. I thought getting past the KB5034441 update error would be simple since I had managed similar awhile ago on a different PC. I tried the manual...
Regarding KB5034441 with 0x80070643 Error
in Windows Updates and Activation

Hi all Generally, Windows Update works well on my WIndows 10, and I frequently update. Several weeks ago, I got a problem with KB5034441, with Error 0x80070643.
Hi. Some background. Two desktop pcs. One with a single 250Gb SSD disk. Encountered the KB5034441 / 0x80070643 error and fixed it by disabling reagentc, resizing the OS partition, deleting and re-creating the WinRE partition, then enabling...
Windows Update KB5034441
in Windows Updates and Activation

Hi guys, after successfully installing KB5034441 on windows 10 22H2 19045.3930 via windows update I got the following WINRE version: 403401 Just wanted to check the version is correct and is the most current? Shouldn't the service pack build...
HP EliteDesk 705 G5 Desktop Mini PC running Windows 10 Pro 64-bit v20H2, Build 19042.985. New from Cheap Laptops, Chromebooks, and Desktop deals | Technoworld and first setup on 12th January 2021. Looking at the installed programs list I see...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

 © Designer Media Ltd
All times are GMT -5. The time now is 12:36.
Find Us




Windows 10 Forums