Windows 10: Boot loop after update no safe mode option-repair fails- restore fails

Page 4 of 11 FirstFirst ... 23456 ... LastLast
  1.    28 Jan 2018 #31

    Sorry I was responding while you were. Tried bcdedit export and it fails.
      My ComputerSystem Spec

  2.    28 Jan 2018 #32

    Have you executed below command to point Command Prompt to C: drive?

    Code:
    C:
      My ComputerSystem Spec

  3.    28 Jan 2018 #33

    Yes I did that before executing ecdedit /export.
      My ComputerSystem Spec

  4.    28 Jan 2018 #34

    Lets rebuild boot files again.


    Can you please post screenshot of below commands:


    Code:
    Diskpart
    
    List Volume
      My ComputerSystem Spec

  5.    28 Jan 2018 #35

    Click image for larger version. 

Name:	20180128_102733.jpg 
Views:	0 
Size:	977.8 KB 
ID:	174538
      My ComputerSystem Spec

  6.    28 Jan 2018 #36

    Please execute following command:

    Code:
    bcdboot E:\Windows /s C: /f  ALL
    Make sure to execute Exit command to exit Diskpart command before executing bcdboot command.

    You may need to replace E: drive letter with Windows OS installed partition drive letter.

    Restart your computer.
      My ComputerSystem Spec

  7.    28 Jan 2018 #37

    Ok executed it and it reported as successful but restart results in a rapid boot cycle. I shot a video to try and read the message that flashes on the screen. It says "working on updates 75% dont turn off your pc. This may take a while. Your pc will restart several times".
      My ComputerSystem Spec

  •    28 Jan 2018 #38

    Please boot your computer with Windows Setup Media and from Windows Recovery Environment start the Command Prompt.


    Please execute below command and reboot your computer to see issue resolves.


    Code:
    DISM    /Image:E:\     /Cleanup-Image   /RevertPendingActions
    Please replace partition letter E: with Windows installed partition letter. When computer boots into Windows Recovery Environment (WinRE) environment the drive letter assign to Windows partition may not be C: drive letter because Windows 7, 8 , 8.1 and 10 creates a separate system partition when it's installed from scratch. The system partition contains boot files WinRE assigns the system partition the C: drive letter and the Windows installed partition will be assign any other drive letter usually D: drive letter is assign to Windows installed partition. The Bcdedit /enum | find "osdevice" command can be use to find out the drive letter of the Windows installed partition the output of the Bcdedit command is similar to this osdevice partition=D:. The drive letter after partition= is the drive letter of the Windows partition.
      My ComputerSystem Spec

  •    28 Jan 2018 #39

    Fails
    Click image for larger version. 

Name:	20180128_111243.jpg 
Views:	1 
Size:	719.5 KB 
ID:	174540
      My ComputerSystem Spec

  •    28 Jan 2018 #40

    Restart your computer and try again please.


    Please execute following commands:

    Code:
    mkdir E:\scratch
    
       DISM /Image:E:\ /Cleanup-Image /RevertPendingActions /scratchdir:E:\Scratch
    Restart your computer.
      My ComputerSystem Spec


  •  
    Page 4 of 11 FirstFirst ... 23456 ... LastLast

    Related Threads
    Hi, I have a desktop Windows 10 x64 machine that's been working fine for months/years. It was automatically updated from Win7 last year. This morning I replaced the 2x4GB DDR3 memory with 2x8GB DDR3. This seemed to work though for some reason...
    My current windows 10 installation is too bogged down to play games properly. I've tried all the traditional solutions to speed up my PC but none of them made any noticeable difference, so I'd like to try a fresh OS. I'd prefer to avoid doing a...
    In MSconfig I set windows to boot into safe mode, now it will not boot at all. Previously it booted into normal mode. I used a Windows recovery disc from which the only option that works is the command prompt. From the cmd prompt I can see all of...
    Obviously I can't click on anything or type anything because the loop is constant. I've been reading forums etc for the past couple of days for a fix for this Automatic Repair loop..nothing that would help and I notice many others the past year also...
    Hello I have a laptop that I took the HDD out of and connected it to another Windows 10 machine. I ran the command Dism /Image:e:\ /Cleanup-Image /RestoreHealth but get the error Deployment Image Servicing and Management tool Version:...
    Our Sites
    Site Links
    About Us
    Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

    Designer Media Ltd
    All times are GMT -5. The time now is 06:27.
    Find Us