Windows 10: NVIDIA GRAPHICS FIRMWARE UPDATE TOOL FOR DISPLAYPORT 1.3 AND 1.4

Page 2 of 4 FirstFirst 1234 LastLast
  1. Cliff S's Avatar
    Posts : 21,752
    Win10 Pro, Win10 Pro N, Win10 Home, Win10 Pro Insider Fast Ring, Windows 8.1 Pro, Ubuntu
       06 Jun 2018 #10

    eLPuSHeR said: View Post
    Thanks Cliff. Sorry to hear about your back health issues. I really hope you get better soon.
    You're welcome, and thanks for the well wishing.
    On the 22nd they're going to stick me it the MRT tube and take a look, because not only the lower back hurts(possible lumbago), but also everything under my knee is slightly numb, like in the winter when you stand around in the cold too log with out moving.
      My ComputersSystem Spec

  2.    06 Jun 2018 #11

    Updated ok.
      My ComputersSystem Spec

  3.    06 Jun 2018 #12

    the vbios version in gpuz dont change.
    I found that it updates uefi nvidia gop!
      My ComputerSystem Spec

  4.    06 Jun 2018 #13

    Cliff S said: View Post
    You're welcome, and thanks for the well wishing.
    On the 22nd they're going to stick me it the MRT tube and take a look, because not only the lower back hurts(possible lumbago), but also everything under my knee is slightly numb, like in the winter when you stand around in the cold too log with out moving.
    I had the same issue a few years ago. Bad back and numbness down below knee on right leg. MRI revealed a couple bulging discs. Had scope surgery and back is fine but I let it go too long and some of the numbness remained in the leg as the nerves died. Good Luck
    Also my update went smooth also.
    Last edited by stealth2920; 06 Jun 2018 at 07:04.
      My ComputerSystem Spec

  5. Cliff S's Avatar
    Posts : 21,752
    Win10 Pro, Win10 Pro N, Win10 Home, Win10 Pro Insider Fast Ring, Windows 8.1 Pro, Ubuntu
       06 Jun 2018 #14

    stealth2920 said: View Post
    I had the same issue a few years ago. Bad back and numbness down below knee on right leg. MRI revealed a couple bulging discs. Had scope surgery and back is fine but I let it go too long and some of the numbness remained in the leg as the nerves died. Good Luck
    Also my update went smooth also.
    Thanks.
    Well at least it wouldn't hurt so damn much, when I bang my shin on the forklift's front wheel wells
      My ComputersSystem Spec

  6. Faith's Avatar
    Posts : 543
    Windows 10 Home October 2018 Update 64-bit
       06 Jun 2018 #15

    I'm using displayPort 1.2 monitors and I just updated without issues. In case I ever get a DP 1.3 or 1.4 monitor with crazy 4K, 120Hz, HDR and Gsync, my graphics card is now supported.
      My ComputerSystem Spec

  7. JGToy's Avatar
    Posts : 257
    Windows 10 Pro x64-bit Build Latest
       06 Jun 2018 #16

    @Brink
    Thanks for the info, I didn't even know about it.
      My ComputerSystem Spec

  8. ThrashZone's Avatar
    Posts : 3,882
    3-Win-7Prox64 2-Win10Prox64
       06 Jun 2018 #17

    essenbe said: View Post
    I just updated my firmwate and tried to update the graphics driver and ended up with nothing but a black screen.Nothing I tried would fix it. Maybe I could have fixed it eventually if I kept trying, but I just restored a Macrium image I had made yesterday. Now I am back up and running fine.

    It wasn't the firmware update that caused it. I rebooted twice after that update with no problems. I think it was DDU. After uninstalling the old drivers I used DDU to boot into safe mode which it refused to do. Besides, the FW update for the card has nothing to do with Windows or drivers if it did what I think it did, which is a BIOS update to the card. That part went smooth and worked fine.

    At any rate, Macrium to the rescue again.
    Hi, @essenbe
    I was thinking our firmware update might have to come from evga
    Seeing evga made our bios and there are 2 master and slave bios on the ftw3 ?
      My ComputersSystem Spec

  9. essenbe's Avatar
    Posts : 11,359
    Windows 10 Pro and Windows 10 Pro Insider
       06 Jun 2018 #18

    The update tool updated mine Mike. I'm pretty sure you would have to do it twice. It should update only the bios you are booted into.
      My ComputersSystem Spec

  10.    06 Jun 2018 #19

    I had never noticed any problems, but the tool said I needed the update. So I got it. All seems OK.
      My ComputerSystem Spec


 
Page 2 of 4 FirstFirst 1234 LastLast

Related Threads
Hi, forums I just updated my windows 10 to version 1803 and It has brought some issues. First, my HDMI port is not working, I am on a laptop btw so it's an integrated graphics card. I also can not access my Nvidia control panel because it gives...
I have a newly bought acer E 15 laptop with i5-8th gen 4GB RAM DDR3L Intel UHD 620 and a dedicated nVidia MX150 2GB GDDR5 Graphics Card. I wan't to use nVidia as my PRIMARY GRAPGICS CARD. 182864 All I can see here is Intel UHD 620 as my...
After the recent Win10 update, my nvidia graphics cards were updated too (Titan+1070) and since whenever I use Blender 3D (and I suppose any other graphics software including games but I haven't tried) audio (ie. background music) is making random...
One of the updates from today (KB3176495 or KB3176931) caused my DisplayPort monitors to be completely undetectable to Windows 10. I'm using an Nvidia 980 ti and the HDMI port appears to be working fine. The graphics drivers are up to date and have...
what is this update and it fails to install.

Tags for this Thread

Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 12:06.
Find Us