Move Users Folder Location in Windows 10  


  1. Posts : 9
    windows 10 edu x64
       #180

    yep, i read about drive letter warning. i relocated the folder to d:\ which is my data partition. i think i typed everything right and i doubt my dvd is corrupted. i namely upgraded from this dvd. i went to recovery and used command prompt to rename the drive letters, the process changed my data partition to something else. the loop is although still there. is there other solution than reinstalling? i dont want to lose my apps and settings, system restore was disabled and i didnt make an image of the system yet. thanks. o yea, i had a users folder on d: from before, when i used windows 7.
      My Computer


  2. Posts : 17,661
    Windows 10 Pro
    Thread Starter
       #181

    The big blueish note box telling how to create a system image before proceeding at the beginning of the tutorial is just because of this, to avoid the loss of your data and installed software.

    I am sorry but if the Windows goes to reboot loop after the sysprep it always indicates a user caused error. In these cases there's nothing to do but to either restore a system image, or to reinstall.
      My Computer


  3. Posts : 9
    windows 10 edu x64
       #182

    what if i move d:users back to c: ? red flame says he did it and it worked.

    my dvd medium is ok , i have install.wim in sources folder

    but i might have forgotten to change the #windows 10 pro line to education, i am not sure
      My Computer


  4. Posts : 17,661
    Windows 10 Pro
    Thread Starter
       #183

    How will you move your Users folder back if you can't boot?
      My Computer


  5. Posts : 9
    windows 10 edu x64
       #184

    run command prompt from windows 10 cd? repair windows. but i still dont understand this drive letter renaming. when exactly do i rename my data partition (to be the location of users folder)? i dont see any meaning in your procedure with renaming the volume to something else and then immediately back to D before sysprep is run. can you explain this please?
      My Computer


  6. Posts : 17,661
    Windows 10 Pro
    Thread Starter
       #185

    You can try but as there's a failed sysprep "under the hood" I doubt if it will work. Please post about how it went!
      My Computer


  7. Posts : 9
    windows 10 edu x64
       #186

    ok, i'll try. read my previous post again, please, i added something
      My Computer


  8. Posts : 17,661
    Windows 10 Pro
    Thread Starter
       #187

    When you change the drive letters manually, they stick. If you don't do it, sysprep defaults them. I cannot explain it any simpler way than what I have already done in the tutorial:

    warning   Warning
    If you intend to use drive D: as the location for the relocated Users folder, please read this before proceeding!

    When Windows is sysprepped it resets the drive ID letters to default:
    • Drive C: > The system drive where Windows will be installed
    • Drive D: > First optical drive (CD / DVD drive)
    • Drive E: > Second partition on the same disk where the C: is located, or in case that disk only has one partition, the first partition on the secondary disk

    Now when you sysprep telling it to move the Users to D: drive, after the reboot Windows finds that the D: is an optical drive and your intended drive D: is now E:, sysprep fails and you have to reinstall.

    To be able to use drive D: for the relocated Users folder you need to set the drive letters manually before the sysprep is run. In Audit Mode you can do this for instance with Disk Management by manually changing the drive letters:
    • Change the optical drive letter to something at the end of the alphabet, I use X:
    • Change the drive letter of the partition or disk you intend to use for the Users folder to D:
    • If the partition or disk you want to use already has a letter D:, change it to something else, close the Disk Management, open it again and change the letter back to D:

    See the tutorial at our sister site the Seven Forums: Drive Letter - Add, Change, or Remove in Windows - Windows 7 Help Forums

    I recommend to always set drive letters manually to override the defaults but this is extremely important for those wanting to use drive D: for relocated Users folder.
      My Computer


  9. Posts : 9
    windows 10 edu x64
       #188

    that is not true in my case. i definitely changed my data partition letter manually but sysprep messed it up obviously
      My Computer


  10. Posts : 9
    windows 10 edu x64
       #189

    ok, i ran this procedure once again on my laptop, point to point, i followed every step in detail. renamed the d partition twice, empty d drive, now it starts looping when the "defaultuser01" appears on the screen. i think this procedure is a rulete. it practically isnt safe and appropriate like it was in win 7 when it could be done failproof. both my install dvds are ok, i checked. im not using this anymore. is there any other, working solution?
      My Computer


 

Tutorial Categories

Move Users Folder Location in Windows 10 Tutorial Index Network & Sharing Instalation and Upgrade Browsers and Email General Tips Gaming Customization Apps and Features Virtualization BSOD System Security User Accounts Hardware and Drivers Updates and Activation Backup and Restore Performance and Maintenance Mixed Reality Phone


  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 08:08.
Find Us




Windows 10 Forums