Windows 10: Windows 10 Recovery Tools - Bootable Rescue Disk
I was just wondering about that , as I just noticed the Free Version also has the ReDeploy Option too that Kyhi mentioned isn't in Pro too, thanks.
On the new Iso, Macruim Free eventually loads after 2-3 mins? , with what looks like, it trying to install/load a generic USB3 (hub?) driver , (Snipping Tool not on ISO ( or I missed it) or I would of got image for you)
Minitool Partition Pro is loading fine too now for me , tried it after Macrium Free.
Last edited by Kbird; 07 Jul 2016 at 18:32.
FSCapture - replaced snipping tool
You may also want to try and pre-load your raid driver into pese image
OK - so have one program request = add back snipping tool...
OK - so have second program request = add back MR Home...
YES, I'm taking requests and suggestions...
For Next release...
Thanks again.... it does sound like I need to do a MRF iso and intergrate it instead.
I guess MR Home is a Trail version ? you don't need a Key / license to run it do you ? I was wondering if that is why it wont load on .125 as MRF runs on .707
I was not aware of FS Capture actually......
.125 may not have all the drivers that are in .707
PE development over time
Angels have the Phone Box
All links and hashes checked out for me. Thanks!
Always advisable to format wih FAT32 so that it will be compatible with earlier version of EFI firmware.
Should the USB Drive be Fat32 or NTFS Formatted? does it matter?
Thanks for following up Topgun , I decided to go the Fat32 route for now as I have mixed UEFI/Legacy/EFI systems...
My first post on Forum, will try to endovour to do my best within guidelines. I am working on a Win10 installation for my neighbour on ASUS TP200SA. The job has just about gone over my head. Main problem I have had, system would not upgrade to the November ISO, to me it looked like it did.
I am however not very familiar with Win10, though I believe I am past this stage and now trying to use MacriumReflect Free to work out a simple recovery system for the owner when I discovered that Macrium Reflect Repair stick lost the keyboard and touchpad.
Searching for some help, I stumbled on this thread. The WinPE boot system seems perfect to experiment with Macrium and see how keyboard/touchpad perform. If need be export drivers from host system if I understand correctly.
During the download of WinPESE-64 around 70% we had a power blackout for an hour, unfortunately Firefox was unable to resume, using the trick to remove the *iso.part to another directory then restart download. As I have blown my download quota I will have to wait another 24 hours before starting over again.
My question the download link in post #1 is that "resumable" or is it Firefox that fails the operation. Firefox is very basic, I have not customised it in any way yet.
My post above is now of less interest as I have downloaded a new copy, WinPESE-64 and made a boot stick. Seems I have been caught out as the ASUS TP200SA running Win10, response is "Not enough memory to make a RAM disk" ooops this pc has only 2 GB or RAM.
When reading the whole thread I must have missed the specs needed to run the WinPE.
Question: How much RAM is needed to run the WinPESE-64?
Does anyone know how this software can be configured to boot from usb on uefi/gpt.
I formatted usb using rufus on the relevant mode then dragged over the contents of another usb where it does work on bios/mbr set up.
But when booting...
Have a new Double Power 8.1 Tablet that I've upgraded to Win 10. Now I've got it set up just right, I'm attempting to create a Rescue Disk. Purchased a 16gb micro-usb drive which is successfully recognized. Ran 'Create Rescue Disk' from Windows...
I have a new laptop with win 7 pro installed. Once Win 10 is installed in July how will I be able to create a system restore disk?
Just sharing this.
I made another boo-boo today and deleted 500GB worth of media files (just movies and music). Don't ask me how because that's something nobody wants to do. :)
I don't keep a backup of these files. For me these are disposable...