It's an old MB (Z68).
For some reason the SATA mode was set as IDE on BIOS. Changed to AHCI and now it is working.
Thanks to all.

On my MB, the M.2 shares the PCIe lane with SATA 5 (last out of 0, 1, ...5) so when one is in use, the other can't be.
You should read the MB manual

No, there isn't.

Never had any of your mentioned problems. It may be a hardware issue.
There is a dedicated page at the forum to treat BSOD etc
https://www.tenforums.com/bsod-crashes-debugging/

Going to ask to...

If the cell phone isn't 100% charged, when you connect the USB cable to transfer data it also charges the phone and that is the situation where it can overload the USB port

sorry, I can't think of anything else

Modern cell phones charge drain's a high current from the USB that can easily damage the MB USB port.
What I do is to charge my cell phone on an external charge and only connect the cell phone to...

If drive 0 has no data, do a win 11 clean install, deleting all partitions on the drive and then proceed.
You must detach (power or SATA cable) drive 1 (win 10) or you will end with Win 11 on drive...

You are probably using one 16G stick and one 8G and this configuration can cause a lot of issues.

Are they are same brand, same type, speed, latency etc?

Using different sizes, even same brand,...

You have to find out what is using almost all your memory.
Are you overclocking?
Why, on OpenHardwareMonitor it isn't showing the minimum column?

The front panel female USB connectors should be connected to the MB USB headers by a cable so there should be no issues.
Can only think of corrosion on the contacts on the MB USB headers. Spray a...

Is the CPU fan running properly?
Why is memory almost all being used (99.8%)?
Is virtual memory enabled?

I would say it is overheating
Use OpenHardwareMonitor to see your temperatures
Extract to C:\Program Files (x86)\HardwareMonitor and run OpenHardwareMonitor.exe
Under options you can set to start...

Use OpenHardwareMonitor to see your temperatures
Extract to C:\Program Files (x86)\HardwareMonitor and run OpenHardwareMonitor.exe
Under options you can set to start with Windows and what to show...

Temperatures should never exceed 85ºC or 185ºF.

sfleury, did you succeeded in upgrading to Win 11?

gabrielsmit did you run CrystalDiskInfo?

Good job. You automated the instructions I posted above. You only didn't give the last partition (Data) the label.

Leave the 1T drive where it is now

To create a MBR partitions on drive 1

Open a CMD window as administrator and type:

diskpart
select disk 1
clean (this will erase all partitions)
convert...

So you did a clean install not to a unallocated space but on a configured partition.

Check if you have WinRE.wim on C:\Windows\System32\Recovery

Just create the partitions and I will instruct how to load the boot manager on the System partition and create a recovery environment on the Recovery partition.
If you tell me how big you want the...

The issues you're facing are related to a non standard installation. In this case you can't complain against M$.
I hope you disabled the recovery environment on the Recovery partition (reagentc...

In my opinion, good thermal paste never needs to be replaced.
Try to find a Asus S530FA service manual.
Open the back cover. My Asus has tork screws so you may need small tork screwdriver.
Try to...

On a MBR drive:
- System partition - NTFS - 100M
- C: partition - NTFS - 80G (if it will have no data, otherwise as big as you wish)
- Recovery - partition - NTFS -1G
- Data Partition - NTFS - As...

There is no Recovery partition on the drive.
Why did you deleted the partition?
Did you disabled the recovery environment on the Recovery partition (reagentc /disable) before the delete partition?...