409952
Pictures not the best, my camera blooms a bit on light sources like LED's.
The OLED display is showing
Battery Status
4.08V 92%
Something like that, I'm typing in what it's displaying...

Having some issues with the weather station mockup. Not exactly sure what's going on? It's just freezing / locking up. I have to do a reset to get back in with Thonny. I think it might be my ICP10125...

This is a second build based on an Inventor 2040 W. It's going to be a test station for servos and motors.
409842
It has a 1.12" Mono OLED (128x128, white/black) Breakout – I2C, and an i2c RGB...

This the current state of my Inventor 2040 W (Pico W Aboard) Rover project.
409841

It's a bit hard to see but there is a VL53L5CX 8x8 Time of Flight (ToF) Array Sensor Breakout mounted up front...

Also tinkered a bit with these.
409840
The top one is an Omnibus With a Display Pack, Pico, and Proto Pack board. Something to mess with when I'm board.
The bottom one is an Adafruit Can Bus...

Was tinkering with this. It's a mock up of what will be an outdoor weather station / system. I've been working on this thing for ages. Hopefully this summer i get it finally all installed outside....

Bought some stuff from Adafruit a while back. And got a free KB2040.
Adafruit KB2040 - RP2040 Kee Boar Driver : ID 5302 : Adafruit Industries, Unique & fun DIY electronics and kits
As shipped I...

I hate it when that happens. I've been in similar situations. You hammer away at code and all seems good. Then the one step forward two steps back hits you. :(

Boy does my Pico Breakout Garden Base makes life a lot easier when I buy new Breakouts. Plug then in, run some code, verify all is good. No having to solder on headers or actually wire them up to...

Spied this on the Pimoroni Github.
ST7701 Display Driver for Pimoroni LCDs
The ST7701 driver supports both Parallel and Serial (SPI) ST7701 displays and is intended for use with:

Redacted...

I buy the CBD oil. It's easy to take and easy on the lungs. ;) And you can select how strong you want it.

I have one of those. I'll soon be setting up. I'll be using cannabis seeds with mine. :-)

I'm still quit active. I have days where I don't do didly squat. But on days that I'm not feeling bad I have at it. Mostly Pi stuff at the moment. I'm putting together stuff I haven't used in a while...

If your using the Official Pi 7 inch touch screen, with a Pi 4 or Pi 3, don't use Bookwork. I installed 64 bit Bookworm and had issues with the graphics on my two touch screens. One is on a Pi 4B 8...

I have dozens of Raspberry Pi Single Board Computers here. Some run headless, some command line only, and some with a full Desktop GUI. They run Pi OS, which was originally based on Debian and was...

I can remember when a floppy disk, was floppy and only held 360 kilobytes. :eek:

Bigger Smaller Better Faster works for me. My Raspberry Pi SBC's use a Micro SD Card as a Hard Drive.

I have no intension of retiring any hardware as a result of Windows 10 lack of support. I'll just keep running Windows 10 as is anyway. Just my personal choice. It's not like I haven't done it...

Monitors are one thing I am in short supply of. My main Windows PC is using three monitors. And I'm in no hurry to reallocate any of those to something else. My one spare HDMI monitor gets cycled...

Spotted a link to this on the Pi Forum.
Raspberry Pi showcase AI camera kit, new screen and long awaited M.2 HAT at Embedded World conference | Tom's Hardware

Just a moment...

There is a...

Missed this the first time through this guide.
Scroll to the bottom, object tracking and following.
MicroPython and VL53L5CX
I should be able to edit / tweak it to run on my Inventor....

Catnip
It's early days yet. Took a break from it today. The pain in my neck and shoulders is brutal. And a pinched nerve in my neck is causing pain all the way down my left arm. Little finger and...

The guy that helped me sort out the encoders did up a custom test build for the Inventor 2040W with ULAB in it. That has got it working. I just finished soldering it in place on the front of my...

I have my speed sensing code sorted out thanks to ZodiusInfuser on GitHuB
Inventor 2040 W, some examples don't work correctly? . Issue #922 . pimoroni/pimoroni-pico . GitHub
New problem, the...

I measured it, it was 3.141592653589793238462643 inches long. Definitely a Micro Python. ;)

On a more serious note. Decided to have a salad today. Needed a bit of a change from the usual something and French fries. Ripped the plastic bag open and and dumped it into a bowl and a bloody snake...