Problems with SFC, Dism and Windows Update

Page 1 of 4 123 ... LastLast

  1. Posts : 48
    Windows 10
       #1

    Problems with SFC, Dism and Windows Update


    Greetings!

    I have the following problem in progress.
    I try to update Windows and give error 0x8007025d, so when I run and SFC it stops at 57 percent.
    I wanted to do an inplace to solve the problem however, MediaCreationTool1909 returns me that I have to update to 2004, but the update for 2004 is not yet available for my notebook on Windows Update, the warning that I have to wait for the update to appear is displayed. my device.
    "The Windows 10 update of May 2020 is on its way.
    When your device is ready you will see the update available on this page. "
    I've tried to repair Windows Update in whatever way I found on the internet, so here comes my question, does anyone know how to force Windows Update to update in brute force mode, or redoing my question, how to find out exactly which files are corrupt and how reset them from a Windows installation media, since the Dism command doesn't work either?

    The dialogues follow.

    There were problems installing some updates, but we'll try again later.

    2020-06 Cumulative Update for Windows 10 Version 1909 for x64-based Operating Systems (KB4560960) - Error 0x8007025d

    Microsoft Windows [version 10.0.18363.836]
    (c) 2019 Microsoft Corporation. All rights reserved.

    C: \ windows \ system32> Sfc / scannow

    Starting file verification. The process will take a few minutes to complete.

    Starting verification phase of system verification.
    57% verification completed.

    Windows Resource Protection cannot perform the requested operation.

    C: \ windows \ system32> Dism / Online / Cleanup-Image / RestoreHealth

    Deployment Image Maintenance and Management Tool
    Version: 10.0.18362.1

    Image Version: 10.0.18363.836

    [================= 29.6%]
    Error: 605

    The specified buffer contains malformed data.

    The DISM log file can be found at C: \ windows \ Logs \ DISM \ dism.log

    C: \ windows \ system32>
      My Computer


  2. Posts : 35,000
    Win 10 Pro (1903) (2nd PC is 21H2)
       #2

    Hi, I understand you have build 1909. Be aware you can freely download every single build of Win 10, but not as you've tried. First, some basic checks, just in case.

    a. Check your disk. Download install and run HD Tune v2.55 free e.g. from Softpedia.com. Health and Error scan tabs.
    b. If ok, run chkdsk c: /scan from an admin command prompt.

    Post back if either fail.

    There's a huge list of useful tutorials here.
    Windows 10 Tutorial Index

    From that see:
    Download Windows 10 ISO File

    Use the Heidoc downloader to get build 1909.

    Log in, rt click and Mount the iso file; open the new drive letter and click setup.exe to attempt an in-place upgrade repair install.
    Last edited by dalchina; 28 Jun 2020 at 01:17.
      My Computers


  3. Posts : 39,972
    windows 10 professional version 1607 build 14393.969 64 bit
       #3

    Run V2 and DM and upload results directly into this thread:
    BSOD - Posting Instructions


    https://www.tenforums.com/tutorials/...dows-10-a.html
    Change Display Language in Windows 10


    How to Upload and Post Screenshots and Files at Ten Forums


    Run this Powershell script and post a share link into the thread using one drive, drop box, or google drive:

    Code:
    function wh   
        {  
            Param ( [parameter (Mandatory = $true)][string]$txt )  
            Write-Host $txt -ForegroundColor Green -BackgroundColor Black -NoNewline  
            ##Example usage wh "Alias for `n Write-Host"  
      
        } ## End function wh  
      
      
    function StartScript   
        {  
            ##Locating Temp Dir and writing Transcript  
            $global:tempDir = [System.IO.Path]::GetTempPath()   
            MD $tempDir\LOGS -EA SilentlyContinue   
            CD $tempDir\LOGS  
            $txtCount = Get-Item $tempDir/LOGS/*.TXT -EA SilentlyContinue  
            if((Get-Host).Version.Major -cge 5) ##WIN7 Not Supported  
                {  
                    if($txtCount.Count -cge 1)   
                    {Start-Transcript -Append -Path $tempDir/LOGS/Event-Search.TXT}   
                    Else{Start-Transcript -Path $tempDir\LOGS\Event-Search.TXT}   
                }  
      
            $global:explore = $tempDir + "LOGS\"  
            $global:Ver = "1.6.3"  
            wh "`nLog Collection... (V$Ver)`n"  
      
            #clearing previous actions  
            Stop-Job *  
      
            #Initialize CheckBox Vars to $True/$False  
                $Global:EventsCollect = $true; $Global:SetupDiagCollect = $true  
                    $Global:UpdatesCollect = $true; $Global:WLANCollect = $true  
                        $Global:PowerCollect = $true; $Global:GPCollect = $true  
                            $Global:miscCollect = $true; $Global:bingCollect = $true  
                                $Global:eventOut = $false        
            #Clear Jobs  
            Stop-Job *  
            Remove-Job *  
                                              
        } ## End function Start-Script  
      
      
    function SetupDiagFunc  
        {  
            wh "`n Grabbing SetupDiag.exe ..."       
            Invoke-WebRequest https://go.microsoft.com/fwlink/?linkid=870142 -OutFile $tempDir\SetupDiag.exe -TimeoutSec 3 -UseBasicParsing  
                #check for successful download  
                if((Get-Item $tempDir\SetupDiag.exe).length -gt 100000)  
                    {  
                      wh "`nSuccessful DL!"  
                      wh "`n Invoking SetupDiag.exe ..."  
                      $SetupDiag = {CMD.EXE /C "%temp%\setupdiag.exe /Verbose /Output:%temp%\SetupDiag-Log.txt"}  
      
                      ## Kick-Off SetupDiagJob  
                      Start-Job -Name SetupDiagJob -ScriptBlock $SetupDiag                     
                      
                    }Else{Write-Host "`nDownload of SetupDiag.exe Failed!" -BackgroundColor RED }  
      
        } ## End Function SetupDiagFunc  
      
      
    function EventSearch  
        {  
        wh "`n Starting EventSearch Job-Function ...`n"  
        ## Gathering Events from System using Get-WinEvent via Job  
        $EventSearchJob =   
            {  
            $evtPaths = Get-Item C:\Windows\System32\Winevt\Logs\*.evtx -Exclude "*PowerShell*",   
                "*known folders*" | Select-Object FullName  
            $i = $evtPaths.Count  
      
            $x = 0 ##For 1st Loop do Until x = i  
            $events = @()  
            $gatherEvents = @()  
            $eventsArray = @()  
            $searchResult = @()  
            $MaxEvents = 99  
      
            #Loading/Gathering Events Loop...  
            do {  
           
                ##Getting Events w/ Get-WinEvent         
                $gatherEvents = Get-WinEvent -Path $evtPaths[$x].FullName -MaxEvents $MaxEvents -EA SilentlyContinue  
                $events = $events + $gatherEvents             
      
                $x++  
                  
                }  
                 Until ($x -eq $i)      
      
            $x = $x +1 ##Total Events Found!  
              
            $eventsLength = $events.Length ##Total events catalogged!  
              
            $xx = 0  
                   
            # Write Event Properties to a row and roll it out - Collapsing Array ...   
            do {  
                   $date = $events[$xx].TimeCreated | Get-Date -Format "yyyyMMdd".ToString() -EA SilentlyContinue ##EA SC for Blank Entries  
                      
                    $eventRow = new-object PSObject -Property @{  
                    Date = $date;  
                    Id = $events[$xx].Id;  
                    Level = $events[$xx].LevelDisplayName;  
                    Provider = $events[$xx].ProviderName;  
                   Message = $events[$xx].Message;  
                    }  
      
                    $cRow = $date + " " + "ID:" +  $events[$xx].Id + " " + "Level:" + $events[$xx].LevelDisplayName + " " + "Provider:" + $events[$xx].ProviderName + " " + "Message:" + $events[$xx].Message   
                    $eventsArray += $cRow  
                   
                    $xx++  
                    $d++  
            }  
            Until ($xx -eq $events.Length)  
     
            ##Looking for patterns error or fail in $eventsArray  
            $search = $eventsArray | Select-String -pattern ("error|fail") 
     
            Return $search ## | Write-Output ##Output for job  
      
            } ## End $EventSearchJob  
      
        Start-Job -Name EventSearchJob -ScriptBlock $EventSearchJob  
      
        } ## End function Event-Search  
      
      
    function writeSearch  ##   
        {  
            ##Event Logs Cont.  
            MD $tempDir\LOGS\EVTX\ -EA SilentlyContinue 
     
            ##output to file  
            $search | Group-Object | Sort-Object Count -Descending | Format-Table Count, Name -Wrap > TOP-ERRORS.TXT  
            $search > $tempDir\LOGS\SEARCH.TXT  
      
        if($Global:eventOut -eq $True)  
            {  
            $search | Group-Object | Sort-Object Count -Descending |   
                Select-Object -Property Count, Name | Out-GridView -Title "Top `"Errors`" via EVTX - V-$Ver"  
            }  
      
            wh "`n Collecting Matching EVTX Entries ...`n"     
            #Collecting all prev matching EVTX  
            #$evtx = Get-ChildItem C:\Windows\System32\Winevt\Logs\*.evtx  
            $evv = 0  
                      
               $providerName =   
                   (($search | Select-String "Provider:.*Message:").Matches.Value -Replace   
                          " Message:", "" -Replace "Provider:", "" | Group-Object ).Name  
                  
                #Converting Provider Name to Log Name                 
                $providerName = (($providerName | ForEach-Object {Get-WinEvent -ProviderName $_ -MaxEvents 1 -EA SilentlyContinue}).LogName | Group-Object).Name     
                   $providerName = $providerName -replace "Microsoft.", ""  
                      $providerName = $providerName -replace "Windows.", ""  
                         $providerName = $providerName -replace "`/.*$", ""  
                               
                               
                             $evtx = $providerName | foreach{Get-ChildItem "C:\Windows\System32\winevt\logs\*$_*"}  
      
                    Do{  
                        COPY $evtx[$evv].PSPath $tempDir\LOGS\EVTX\ 
                           $evv++  
                      }  
                      Until($evv -eq $evtx.Count)  
      
        } #End function writeSearch  
      
      
    function GetUpdates  
        {  
            wh "`n Starting Get-WindowsUpdateLog Job-Function ...`n"  
            $updateJob = {get-WindowsUpdateLog}  
             
            if((Get-Host).Version.Major -cge 5) ##Modern Gatherer  
            {  
                Start-Job -Name GetUpdates -ScriptBlock $updateJob  
            }  
              
            ##Legacy Gatherer  
            CP C:\Windows\WindowsUpdate.log $tempDir\LOGS\WindowsUpdate.log  
      
            ##Installed-Updates/Packages 
            Get-WmiObject win32_quickfixengineering > $tempDir\LOGS\Installed_Updates.TXT  
            Get-WmiObject Win32_OperatingSystemQFE >> $tempDir\LOGS\Installed_Updates.TXT  
        DISM /Online /Get-Packages /Format:Table >> $tempDir\LOGS\Installed_Updates.TXT 
      
        } ## End function Get-Updates  
      
           
    function PrinterCheck  
        {  
            wh "`n Getting Printer Information ..."  
            get-printer | ft Name, ComputerName, Type, DriverName, PortName, Datatype, Location, DriverName > $tempDir\LOGS\Printers.TXT  
            get-printerDriver | fl >> $tempDir\LOGS\Printers.TXT  
            Get-ChildItem -Recurse Registry::"HKLM\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows NT x86\Drivers" | Out-File $tempDir\LOGS\Printers.TXT -Append  
            Get-ChildItem -Recurse Registry::"HKLM\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows x64\Drivers" | Out-File $tempDir\LOGS\Printers.TXT -Append  
            Get-ChildItem -Recurse Registry::"HKLM\SYSTEM\CurrentControlSet\Control\Print\Monitors" | Out-File $tempDir\LOGS\Printers.TXT -Append  
            write-output "## CBS ntprint CHECK ##" >> $tempDir\LOGS\Printers.TXT  
            $cbsCheck = (Get-ChildItem C:\Windows\Logs\CBS\*cbs* -Recurse | select-string -Pattern "E_INVALIDARG in eventsXml.*Microsoft-Windows-PrintService")  
            if($cbsCheck.Count -eq 0){Write-Output "## NO MATCHES IN CBS ##" >> $tempDir\LOGS\Printers.TXT} Else{$cbsCheck | Group-Object  >> $tempDir\LOGS\Printers.TXT}  
            write-output "## ntprint.dll CHECK ##" >> $tempDir\LOGS\Printers.TXT  
            (Get-ChildItem C:\Windows\System32\ntprint.dll).VersionInfo | ft -AutoSize >> $tempDir\LOGS\Printers.TXT  
            (Get-ChildItem C:\Windows\SysWOW64\ntprint.dll).VersionInfo | ft -AutoSize >> $tempDir\LOGS\Printers.TXT  
      
        } ## End function PrinterCheck  
      
      
    function UpdateHelper  
        {  
        if((Get-Host).Version.Major -cge 5)  
            {  
                $winupdatelog = get-item $tempDir\LOGS\windows-update.log    ##WIN-10 File  
                MD $tempDir\LOGS\Windows\Logs\WindowsUpdate\ -EA SilentlyContinue | Out-Null  
                CP C:\Windows\Logs\WindowsUpdate\*.etl $tempDir\LOGS\Windows\Logs\WindowsUpdate\ -EA SilentlyContinue  
            }  
                Else{$winupdatelog = get-item $tempDir\LOGS\windowsupdate.log} ##LEGACY File  
      
        $updateError = ($winupdatelog | select-string -pattern "error.*0x........");  
        $updateErrorSplit = $updateError -Split " "  
        $updateErrorCount = (($updateErrorSplit | select-string -pattern "0x........") -Replace "[(),'`.:]", "" -Replace "hr=", "");  
      
        $updateErrorCount | Group-Object | Sort-Object Count -Descending | Format-Table Count, Name | Out-File $tempDir\LOGS\UPDATE-ERRORS.TXT -Width 999  
        $updateError >> UPDATE-ERRORS.TXT  
        if($updateError.length -eq 0){"No `"error.*0x........`" patterns Found in Windows-Update.log" | Out-File $tempDir\LOGS\UPDATE-ERRORS.TXT}  
      
        ($winupdatelog | Select-String "KB\d\d\d\d\d\d\d" | Select-string "fail") | Out-file $tempDir\LOGS\UPDATE-ERRORS.TXT -Append -width 999  
      
        } ## End function UpdateHelper  
      
      
    function getProcesses  
        {  
        wh "`nGetting Active Process ...`n"   
        Get-Process > $tempDir\LOGS\Running-Processes.TXT  
        CMD.EXE /C "tasklist /svc" | Out-File -Append  $tempDir\LOGS\Running-Processes.TXT  
          
        } ## End function getProcesses  
      
      
    function GetApps  
        {  
        wh "`n Getting List of Installed Apps...`n"  
        Get-WmiObject -Class Win32_Product | Format-Table -Property Name, Version, Vendor > $tempDir\LOGS\Installed-Apps.TXT  
        Get-AppxPackage | ft Name, Version, InstallLocation, IspArtiallyStaged, SignatureKind, Status >> $tempDir\LOGS\Installed-Apps.TXT  
          
        } ## End function GetApps  
      
      
    function SetupLogs  
        {  
        wh "`nGetting Windows Setup Logs Independent of SetupDiage.exe...`n"  
            MD $tempDir\LOGS\SETUP\ -EA SilentlyContinue  
        dir C:\ > $tempDir\LOGS\Dir_Structure.txt  
          
        ## Main Setup Collection  
        if($env:SystemDrive -eq 'C:') ##Verify SystemDrive  
        {  
            $SetupPaths = @()  
      
            $locations = @(  
                'C:\GetCurrent',  
                'C:\$Reset',  
                'C:\$SysReset',  
                'C:\$Windows.~BT',  
                'C:\$Windows.~WS',  
                'C:\Windows\Logs\',  
                'C:\Windows\Panther\',  
                'C:\Windows\inf\',  
                'C:\Windows\System32\LogFiles\',  
                'C:\Windows\System32\SysPrep\',  
                'C:\Windows10Upgrade',  
                'C:\Windows.old\Windows\Panther')  
      
            for($i = 0; $locations.count -gt $i; $i++)  
            {   
                if((get-item $locations[$i] -Force -EA SilentlyContinue).length -gt 0) ##Null Path Check -Force for Hidden  
                {  
                    CD $locations[$i]  
                    ##Search includes setuperr/setupact only  
                    $SetupPaths += Get-ChildItem * -Force -Recurse -Include setuperr.log, setupact.log, miglog.xml, *APPRAISER_Humanreadable.xml -EA SilentlyContinue      
                }  
            }  
      
            $cleanPaths = @()  
      
            for($i = 0; $SetupPaths.count -gt $i; $i++)  
            {  
                $cleanPaths += $SetupPaths[$i].PSParentPath.ToString() -replace "Microsoft\.PowerShell\.Core\\FileSystem\:\:C\:\\", ""  
            }  
      
            CD $tempDir\LOGS\SETUP\  
            MD $cleanPaths -Force  
            CD $tempDir\LOGS\  
      
            for($i = 0; $SetupPaths.count -gt $i; $i++)  
            {  
                $destPath = "$tempDir\LOGS\SETUP\" + $cleanPaths[$i]  
                $copyPathLog = ($SetupPaths[$i].ToString())  
                  
                Copy  $copyPathLog -Destination $destPath  
            }  
          
        }Else{Write-Host "`nSystem Drive is not C:... Setup Collection Aborted!`n"}  
        ## End Main Setup Collection  
          
              
            ## Setup Reg Output      
            Get-ChildItem HKLM:\SYSTEM\SETUP\ | Out-File $tempDir\LOGS\SETUP\HKLM_SYSTEM_SETUP-OOBE.TXT  
            Get-ChildItem HKLM:\SOFTWARE\Microsoft\Windows\CurrentVersion\OOBE\Me* -recurse -EA SilentlyContinue | Out-File $tempDir\LOGS\SETUP\HKLM_SYSTEM_SETUP-OOBE.TXT -Append  
            Get-Childitem HKLM:SOFTWARE\Microsoft\Windows\CurrentVersion\WindowsUpdate | Out-File $tempDir\LOGS\SETUP\HKLM_SYSTEM_SETUP-OOBE.TXT -Append  
      
            ## SetupAct String Search  
      
      
              
             $setupRegx = @("MOUPG SetupHost..Initialize:",  
                            "============================",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MOUPG  SetupHost..Initialize. CmdLine"),  
                            "",  
                            "MOUPG Setup build & Host OS Build:",  
                            "==================================",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MOUPG  SetupHost..Setup build"),  
                            "...",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MOUPG      Host OS"),  
                            "",  
                            "Watson Parameters (4&5):",  
                            "=======================",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "Watson Bucketing Parameters\[[4-5]\]" ),  
                            "",  
                            "\[0x........\]Error:",  
                            "==================",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "\[0x........\]\[0x.....\]"),  
                            "",  
                            "`"FATAL`":",  
                            "======",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "FATAL" | Select-String -NotMatch "FatalExecutionEngineError" | Select-String -NotMatch "non-fatal"),  
                            "",  
                            "`"Error   `":",  
                            "===========",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "Error   "),  
                            "",  
                            "MIGRATE.*DATA:",  
                            "==============",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MIGRATE.*DATA"),  
                            ""             
                            )  
                $q=0  
                Do {$setupRegx[$q] | Out-File $tempDir\LOGS\SETUP\SetupAct-Regex.TXT -Append -Width 999 ##spool out results  
                                      $q++                    
                                                }Until($q -eq $setupRegx.Count)  
      
        } ## End function SetupLogs  
      
      
    function powerCFGInfo  
        {  
        MD $tempDir\LOGS\POWER\ -EA SilentlyContinue  | Out-Null  
        wh "`n Grabbing PowerCFG, Sleep & Battery Info ...`n"  
          
        ("`n" + "Available Sleep States (/A): `r" + "`n" +"============================`r" + "`r").ToString() | Out-File -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg /a | Out-File -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "-DeviceQuery Wake_Armed: `r" + "`n" +"========================`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg -devicequery wake_armed  | Out-file -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "Last Wake (-lastwake):  `r" + "`n" +"=====================`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg -lastwake  | Out-file -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        ("`n`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "-Requests: `r" + "`n" +"==========`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg -requests  | Out-file -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        $powerList = powercfg -list  
        $powerList | Out-File -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        $powerActive = $powerList | select-string "\*" | powercfg /QH "$_"   
        ("`n`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "Active Power Scheme Details: `r" + "`n" +"============================`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        $powerActive | Out-File -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
      
        if((Get-Host).Version.Major -cge 5) ##WIN7 Does not Support powercfg /battery /sleepstudy  
             {   
               $ifbattery = Get-WmiObject win32_battery  
               if ( $ifbattery.__SERVER.count -cge 1 ) { CMD.EXE /C "powercfg /batteryreport /output %temp%\LOGS\POWER\battery-report.html" }  
               CMD.EXE /C "powercfg /sleepstudy /output %temp%\LOGS\POWER\sleepstudy-report.html"  
             }  
               CMD.EXE /C "powercfg /ENERGY /duration 10 /output %temp%\LOGS\POWER\energy-report.html"         
          
        } ## End function powerCFGInfo  
      
      
    function sysProductCheck  
        {  
        wh "`n Getting SystemProductName ...`n"  
        ##SystemInformation Reg   
        reg query HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\SystemInformation\ /v SystemProductName  > $tempDir\LOGS\REG_SystemProductName.TXT   
        Get-WmiObject Win32_ComputerSystem > $tempDir\LOGS\WMI_Object_System.TXT  
        Get-WmiObject Win32_ComputerSystemProduct >> $tempDir\LOGS\WMI_Object_System.TXT  
          
        } ## End functions sysProductCheck  
      
      
    function showWLAN  
        {  
        wh "Generating NETSH WLAN Report...`n"  
      
        $showWLANjob = {  
                        CMD.EXE /c "netsh wlan show networks mode=ssid > %temp%\LOGS\Network\wlan.txt"  
                        CMD.EXE /c "netsh wlan show networks mode=bssid >> %temp%\LOGS\Network\wlan.txt"  
                        CMD.EXE /c "netsh winhttp show proxy > %temp%\LOGS\Network\proxy.txt"  
                        CMD.EXE /c "netsh wlan show wlanreport & COPY C:\ProgramData\Microsoft\Windows\wlanReport\wlan-report-latest.html %temp%\LOGS\Network\wlan-report-latest.html"   
                        ##WIN7 Does not Support netsh wlanreport                                                    
                        }   
      
        Start-Job -Name showWLAN -ScriptBlock $showWLANjob  
      
        } ## End function sysProductCheck  
      
      
    function getGPRESULT  
        {  
        wh "`nGetting GPRESULT...`n"  
        CMD.EXE /C "GPRESULT /V > %temp%\LOGS\GPRESULT.TXT"  
          
        } ## End function getGPRESULT  
      
      
    function reservedCheck  
        {       
             
        $reservedJob =   
            {  
            $vol = (mountvol /L | select-string -Pattern "\\\\")  
            $volstring = "mountvol y:" + $vol[0]  
            CMD.EXE /C $volstring  
          
            SLEEP 2  
      
            CMD.EXE /C "CHKDSK y: > %temp%\LOGS\SystemReserved.TXT"  
          
            SLEEP 2 # Pause after drive dismount  
          
            CMD.EXE /C "mountvol y: /D"  
            }  
      
        Start-Job -Name reservedJob -ScriptBlock $reservedJob  
          
        } ## End function reservedCheck  
      
      
    function fltmcCheck  
        {  
        wh "`n Getting fltmc Filters ...`n"  
        CMD.EXE /c "fltmc filters > %temp%\LOGS\fltmc_filters.TXT"  
          
        } ## End function fltmcCheck  
      
      
    function getDXDiag  
        {  
        wh "`n Grabbing DXDiag Info...`n"  
        C:\Windows\System32\dxdiag /x $explore\DxDiag  
          
        } ## End function getDXDiag  
      
      
    function getMSINFO  
        {  
        wh "`n Gathering MSINFO32 ...`n"  
        ## check if msinfo is already gathering - if so stop  
        If((get-process | select-string -Pattern "msinfo").Pattern -eq "msinfo")  
        {Stop-Process -ProcessName msinfo32}  
      
            C:\Windows\System32\msinfo32.exe /nfo $tempDir/LOGS/MSINFO32.NFO  
                     
        } ## End function getMSINFO  
      
      
    function getAV  
        {  
         if((Get-Host).Version.Major -cge 5) ##Modern OS Only  
            {  
            wh "`n Grab root\SecurityCenter2 AntivirusProduct ...`n"  
            $avPath = (Get-WmiObject -Namespace root\SecurityCenter2 -Class AntivirusProduct) | % {$_.pathtoSignedProductEXE}  
            "AV Info" + "`n========" | Out-File $tempDir/LOGS/SecurityProductInformation.TXT 
        $avPath | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append  
            if($avPath[0] -match "exe")  
                {   
                    $path = (Get-Item $avPath[0]).PSParentPath  
                    Get-Item $path/*.ini | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append  
                    Get-Content $path/*.ini | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append             
                }  
                Get-ChildItem "HKLM:\SOFTWARE\Policies\Microsoft\Windows Defender\" -recurse -EA SilentlyContinue | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append      
            }  
        } ## End function getAV  
      
      
    function getDrivers  
        {  
        wh "`n Grabbing Driver listing via DISM.EXE ...`n"  
            $drivers = cmd.exe /C "dism /online /get-drivers /format:table"  
            $drivers += cmd.exe /C "dism /online /get-drivers /all /format:table"  
            $drivers | Out-File $tempDir/LOGS/DISM-Get-Drivers.TXT  
        wh "`n Done!`n"  
        } ## End Function getDrivers  
      
      
    function getMISCLogs  
        {  
            wh "`nCopying misc. logs ...`n"   
            MD $tempDir\LOGS\WER\ -EA SilentlyContinue   
            MD $tempDir\LOGS\Windows\Logs\WindowsUpdate\ -EA SilentlyContinue  
            CP "C:\Users\All Users\Microsoft\Windows\WER\ReportArchive\*" $tempDir\LOGS\WER\ -Recurse -EA SilentlyContinue  
            CP "C:\Windows\Logs\CBS\*cbs*" $tempDir\LOGS\Windows\Logs\  
            CP "C:\Windows\Logs\DISM\*dism*" $TempDir\LOGS\Windows\Logs\  
            CP "C:\Windows\Logs\WindowsUpdate\*" $TempDir\LOGS\Windows\Logs\WindowsUpdate\  
      
                
            #DMP Collect  
            $dmp = @()  
            $dmp += Get-ChildItem C:\Windows\*.dmp   
            $dmp += (Get-ChildItem C:\Windows\LiveKernelReports\*.dmp -Recurse -EA SilentlyContinue)  
            $dmp += (Get-ChildItem C:\Windows\Minidump\*.dmp -Recurse -EA SilentlyContinue)  
            #Validate empty array  
            if($dmp.length -ne 0)  
                {  
                $dd=0  
                      Do{       
                            If($dmp[$dd].length -lt 2000000)  
                                { $destPath = $dmp[$dd].PSParentPath.Replace('C:\', '').Replace('Microsoft.PowerShell.Core\FileSystem::', '')  
                                    MD $destPath -EA SilentlyContinue 
                                        COPY -Path $dmp[$dd].PSPath -Destination $destPath }  
                            $dd++  
                        }  
                        Until($dd -eq $dmp.Count)  
                }  
     
             #disk info 
             "`nGet-Disk:`n=========" > $tempDir\LOGS\Disk-Info.TXT  
             Get-Disk |fl >> $tempDir\LOGS\Disk-Info.TXT 
             "`nGet-Partition:`n==============" >> $tempDir\LOGS\Disk-Info.TXT  
             Get-Partition >> $tempDir\LOGS\Disk-Info.TXT 
             Manage-bde -protectors -get C: >> $tempDir\LOGS\Disk-Info.TXT 
             "`nIO Fail Search:`n===============`n" >> $tempDir\LOGS\Disk-Info.TXT 
             $search | Select-String ".*io.fail.*" | Select-String -NotMatch '0, 0, 0, 0' >> $tempDir\LOGS\Disk-Info.TXT        
      
        } ## End function getMISCLogs  
      
      
    function bingCollect  
        {  
            ##O365 Firewall Check & Bing.com diagnostics.asp  
            ##URIs based on Article:   
            ##https://support.office.com/en-us/article/Network-requests-in-Office-365-ProPlus-and-Mobile-eb73fcd1-ca88-4d02-a74b-2dd3a9f3364d  
                    
            MD $TempDir\LOGS\Network\ -EA SilentlyContinue  
      
            wh "Performing Bing & O365 URI Check ... `n"  
      
      
                  $bingCheck = (Invoke-WebRequest -Uri https://www.bing.com/fdv2/diagnostics.aspx -UseBasicParsing)   
                  $bingCheck | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT  
                     
                  $URIs = @('api.login.microsoftonline.com',    #0  Standard Reply = 403  
                  'api.passwordreset.microsoftonline.com',      #1  Standard Reply = 200  
                  'becws.microsoftonline.com',                  #2  Standard Reply = 403  
                  'clientconfig.microsoftonline-p.net',         #3  Standard Reply = 404  
                  'companymanager.microsoftonline.com',         #4  Standard Reply = 403  
                  'device.login.microsoftonline.com',           #5  Standard Reply = 200  
                  'graph.microsoft.com',                        #6  Standard Reply = 404  
                  'hip.microsoftonline-p.net',                  #7  Standard Reply = 404   
                  'hipservice.microsoftonline.com',             #8  Standard Reply = 404  
                  'login.microsoft.com',                        #9  Standard Reply = 200  
                  'login.microsoftonline.com',                  #10 Standard Reply = 200  
                  'logincert.microsoftonline.com',              #11 Standard Reply = 200   
                  'loginex.microsoftonline.com',                #12 Standard Reply = 200  
                  'login-us.microsoftonline.com',               #13 Standard Reply = 200  
                  'login.microsoftonline-p.com',                #14 Standard Reply = 200  
                  'login.windows.net',                          #15 Standard Reply = 200  
                  'nexus.microsoftonline-p.com',                #16 Standard Reply = 403  
                  'passwordreset.microsoftonline.com',          #17 Standard Reply = 200  
                  'provisioningapi.microsoftonline.com',        #18 Standard Reply = 403  
                  'stamp2.login.microsoftonline.com',           #19 Standard Reply = 200  
                  'ccs.login.microsoftonline.com',              #20 Standard Reply = 401  
                  'ccs-sdf.login.microsoftonline.com',          #21 Standard Reply = 401  
                  'accounts.accesscontrol.windows.net',         #22 Standard Reply = 200  
                  'secure.aadcdn.microsoftonline-p.com',        #23 Standard Reply = 400  
                  'windows.net',                                #24 Standard Reply = 200  
                  'phonefactor.net',                            #25 Standard Reply = 200  
                  'account.activedirectory.windowsazure.com',   #26 Standard Reply = 404  
                  'secure.aadcdn.microsoftonline-p.com',        #27 Standard Reply = 400  
                  'login.windows.net',                          #28 Standard Reply = 200  
                  'provisioningapi.microsoftonline.com',        #29 Standard Reply = 403  
                  'mscrl.microsoft.com',                        #30 Standard Reply = 400  
                  'secure.aadcdn.microsoftonline-p.com',        #31 Standard Reply = 400  
                  'windowsupdate.microsoft.com',                #32 Standard Reply = 200  
                  'update.microsoft.com',                       #33 Standard Reply = 200  
                  'au.download.windowsupdate.com',              #34 Standard Reply = 200  
                  'download.windowsupdate.com',                 #35 Standard Reply = 200  
                  'download.microsoft.com',                     #36 Standard Reply = 200  
                  'tlu.dl.delivery.mp.microsoft.com');          #37 Standard Reply = 403  
              
                     
                  $count = 0;  
                  $queryResult =@{};  
                     
                  Write-Host "Checking URIs .." -NoNewline  
                     
                  Do {           
                          Try{  
                          $queryResult[$count] = (Invoke-WebRequest -Uri ("http:`/`/" + $URIs[$count]) -Method Head -UseBasicParsing -TimeoutSec 2).RawContent  
                             }Catch{ $catch = $_ }  
                     
                              if($queryResult[$count].Count -eq 0)  
                                      {$queryResult[$count] = ($catch[$catch.count -1].ToString()).Replace("`n", " ")}                                     
                          Write-Host "." -NoNewline           
                          $count++         
                      }Until ($count -eq ($URIs.Count));                            
                  Write-Host "."  
                      
                      Get-Date | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT -Append  
                      $queryResult | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT -Append  
                        
            Write-Host " Bing Check", `n, "==========" | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT -Append  
            
                  wh "`n`n`n`URL Check Finished...`n"   
        }  
      
      
    function smbConfig  
    {  
      
        $CMDs =  
        {   cmd.exe /c "net config server"    
            cmd.exe /c "net config workstation"  
            Get-SmbClientNetworkInterface  
            Get-SmbServerConfiguration  
            Get-SmbClientConfiguration  
            Get-ChildItem "HKLM:\SYSTEM\CurrentControlSet\Services\LanmanServer"   
            Get-NetAdapterAdvancedProperty | ft }  
      
        ForEach-Object{Invoke-Command $CMDs | Out-File $TempDir\LOGS\NETWORK\$env:COMPUTERNAME-SMB-Config.TXT -Append}  
      
        $share = Get-SmbShare  
      
        ForEach-Object{Get-SmbShareAccess $share.Name | ft  | Out-File $tempDir\LOGS\NETWORK\$env:COMPUTERNAME-SMB-Config.TXT -Append}  
      
    } ## End Function smbConfig  
      
      
    function regLang  
        {       
            DISM.EXE /Online /Get-Intl  | Out-File $tempDir\LOGS\Reg-Lang.TXT  
            "`n","Get-WinUserLanguageList","=======================" | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
            Get-WinUserLanguageList     | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
            "`n","Get-WinLanguageBarOption","========================" | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
            Get-WinLanguageBarOption    | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
        }  
      
      
    function autoRotate  
        {  
            Get-ChildItem HKLM:SOFTWARE\Microsoft\Windows\CurrentVersion\Auto* | Out-File $tempDir\LOGS\AutoRotate.TXT  
        }  
      
      
    function checkBoxes  
       {  
            Add-Type -AssemblyName System.Windows.Forms  
            Add-Type -AssemblyName System.Drawing  
      
            $Global:form = New-Object System.Windows.Forms.Form  
            $Global:form.Text = "LOGS-V$ver"  
            $Global:form.Size = New-Object System.Drawing.Size(300,400)  
            $Global:form.StartPosition = 'CenterScreen'  
      
            $OKButton = New-Object System.Windows.Forms.Button  
            $OKButton.Location = New-Object System.Drawing.Point(100,300)  
            $OKButton.Size = New-Object System.Drawing.Size(75,23)  
            $OKButton.Text = 'OK'  
            $OKButton.DialogResult = [System.Windows.Forms.DialogResult]::OK  
            $Global:form.AcceptButton = $OKButton  
            $Global:form.Controls.Add($OKButton)  
             
            $Global:form.ControlBox = $false  
              
                $Global:boxNum = 1  
                $Global:checkBox = @{} #hash for $checkBox  
                $tag = @{} #hash for $label  
                $Global:Box = @{}  
      
                function createCheckBox   
                    {  
                        Param ( [parameter (Mandatory = $true)][string]$name,  
                                [parameter (Mandatory = $true)][string]$label )  
                          
                        $drawingPoint = (50 + ($boxNum *25))  
      
                        $Global:checkBox[$boxNum] = New-Object System.Windows.Forms.CheckBox  
                        $Global:checkBox[$boxNum].Location = New-Object System.Drawing.Point(10,$drawingPoint)  
                        $Global:checkBox[$boxNum].Size = New-Object System.Drawing.Size(15,15)  
                        $Global:checkBox[$boxNum].Text = ''  
                        $Global:checkBox[$boxNum].Checked = $true  
                        $Global:form.Controls.Add($checkBox[$boxNum])  
                        #SetupDiag Label  
                        $tag[$boxNum] = New-Object System.Windows.Forms.Label  
                        $tag[$boxNum].Location = New-Object System.Drawing.Point(40,$drawingPoint)  
                        $tag[$boxNum].Size = New-Object System.Drawing.Size(280,20)  
                        $tag[$boxNum].Text = "$label"  
                        $Global:form.Controls.Add($tag[$boxNum])  
      
                        $Global:boxNum ++  
                      
                    } #End nested function createCheckBox   
                
                createCheckBox -name "EV" -label "EventSearch EventLog Helper"       #1  
                createCheckBox -name "SD" -label "SetupDiag.EXE Setup Diagnostics"   #2  
                createCheckBox -name "WU" -label "Get-WindowsUpdateLog Collection"   #3  
                createCheckBox -name "IP" -label "Network Information"               #4  
                createCheckBox -name "PW" -label "POWERCFG. Sleep & Battery Info"    #5  
                createCheckBox -name "GP" -label "GPResult Info"                     #6  
                createCheckBox -name "MS" -label "General Machine Info"              #7  
                createCheckBox -name "EO" -label "EventSearch Out-GridView"          #8            
                     
                #Checkbox State Changes               
                $Global:checkBox[1].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[1].checked -eq $True){ $Global:EventsCollect = $true ; Write-Host "." -nonewline} Else{ $Global:EventsCollect = $false }  
                                  
                        })             
                $Global:checkBox[2].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[2].checked -eq $True){ $Global:SetupDiagCollect = $true ; Write-Host "." -nonewline} Else{ $Global:SetupDiagCollect = $false }  
                                  
                        })  
                $Global:checkBox[3].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[3].checked -eq $True){ $Global:UpdatesCollect = $true ; Write-Host "." -nonewline} Else{ $Global:UpdatesCollect = $false }  
                                  
                        })  
                $Global:checkBox[4].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[4].checked -eq $True){ $Global:WLANCollect = $true ; Write-Host "." -nonewline} Else{ $Global:WLANCollect = $false }  
                                  
                        })  
      
                $Global:checkBox[5].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[5].checked -eq $True){ $Global:PowerCollect = $true ; Write-Host "." -nonewline} Else{ $Global:PowerCollect = $false }  
                                  
                        })  
                $Global:checkBox[6].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[6].checked -eq $True){ $Global:GPCollect = $true ; Write-Host "." -nonewline} Else{ $Global:GPCollect = $false }  
                                  
                        })  
                $Global:checkBox[7].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[7].checked -eq $True){ $Global:miscCollect = $true ; Write-Host "." -nonewline} Else{ $Global:miscCollect = $false }  
                                  
                        })  
      
                 $Global:checkBox[8].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[8].checked -eq $True){ $Global:eventOut = $true ; $Global:checkBox[1].checked = $true; Write-Host "x" -nonewline} Else{ $Global:eventOut = $false }  
                                  
                        })  
                                               
            $Global:checkBox[8].Checked = $false  
            $mainText = New-Object System.Windows.Forms.Label  
            $mainText.Location = New-Object System.Drawing.Point(62,30)  
            $mainText.Size = New-Object System.Drawing.Size(260,20)  
            $mainText.Text = 'Choose which logs to collect:'  
            $Global:form.Controls.Add($mainText)  
            $result = $Global:form.ShowDialog()  
            SLEEP 1  #testing Topmost lag  
            $Global:form.Topmost = $true  
      
            #OK Button ...   
            if ($result -eq [System.Windows.Forms.DialogResult]::OK)  
            {  
                $x = $textBox.Text  
                $x  
            }       
      
        } #End function checkBoxes  
      
      
    Function werHint  
    {  
        $WERs = Get-ChildItem $tempDir\LOGS\WER\*.wer -Recurse  
      
        $WERArray = @()  
      
        $Date = $WERs | Select-String -pattern "eventtime=" | % {$_ -Replace("C:.*EventTime=", "")}  
        $eventType = $WERs | Select-String -pattern "EventType=" | % {$_ -Replace("C:.*EventType=", "")}  
        $Sig0Nam = $WERs | Select-String -pattern "Sig\[0\].Name" | % {$_ -Replace("C:.*Sig\[0\].Name=", "")}  
        $Sig0Val = $WERs | Select-String -pattern "Sig\[0\].Value" | % {$_ -Replace("C:.*Sig\[0\].Value=", "")}  
        $Sig3 = $WERs | Select-String -pattern "Sig\[3\].Value" | % {$_ -Replace("C:.*Sig\[3\].Value=", "")}  
        $Sig3 = $WERs | Select-String -pattern "Sig\[3\].Value" | % {$_ -Replace("C:.*Sig\[3\].Value=", "")}  
        $Sig4 = $WERs | Select-String -pattern "Sig\[4\].Value" | % {$_ -Replace("C:.*Sig\[4\].Value=", "")}  
      
        #ConvertDateTime  
        $epoch = [datetime]"01/01/1601 00:00"  
        $date = $date | foreach{$epoch.AddSeconds($_/10000000)}   
        $convertedDate = foreach($Date in $Date) {Get-Date $Date -Format G}  
      
        $WERarray = 0..($convertedDate.Length -1) | Select-Object @{n="Id";e={$_}},   
            @{n="Date";e={$convertedDate[$_]}}, @{n="EventType";e={$eventType[$_]}},  
                @{n="S0-Name";e={$Sig0Nam[$_]}}, @{n="S0-Value";e={$Sig0Val[$_]}}, @{n="S3";e={$Sig3[$_]}},   
                    @{n="S4";e={$Sig4[$_]}}  
      
        $WERArray |Sort-Object -Descending Date | ft -autosize Date, EventType, S0-Name, S0-Value, S3, S4  |   
            Out-File $tempDir\LOGS\WER-SUMMARY.TXT -Width 500  
      
    } ## End Function werHint  
      
      
      
    ### FUNCTIONS_INIT ###   
      
            $Script:Cancel = @{}  
      
            StartScript #function  
            checkBoxes  
              
            ## SetupDiagCollect   #2  
            if($Global:SetupDiagCollect -eq $True)  
                {  
                SetupDiagFunc #function & job   
                wh "...`n"  
                }  
            ## EventSearch         #1  
            if($Global:EventsCollect -eq $True)  
                {  
                EventSearch #function & job  
                wh "...`n"  
                }  
      
            ## Get-WindowsUpdate   #3  
            if($Global:UpdatesCollect -eq $True)  
                {  
                GetUpdates #function & job  
                wh "...`n`n"  
                }  
      
            ## WLAN/Wifi Collect    #4  
            if($Global:WLANCollect -eq $True)      
                {  
                bingCollect #function  
                wh "...`n"  
                showWLAN #function & job   
                wh "...`n"  
                smbConfig #function  
                }  
      
            ## Power/Battery Collect:#5  
            if($Global:PowerCollect -eq $True)  
                {  
                powerCFGInfo #function - make job takes a min  
                wh "...`n"  
                }  
      
            ## GPRESULT Collection:  #6  
            if($Global:GPCollect -eq $True)  
                {  
                getGPRESULT #function  
                wh "...`n"  
                }  
      
            ## Misc Logs Collection: #7        
            if($Global:miscCollect -eq $True)  
                {  
                getMSINFO #function & job  
                    wh "...`n"  
                PrinterCheck #function  
                    wh "...`n"  
                getProcesses #function  
                    wh "...`n"  
                getApps #function - make job - takes a min  
                    wh "...`n"  
                SetupLogs #function  
                    wh "...`n"       
                sysProductCheck #function  
                    wh "...`n"                 
                reservedCheck #function  
                    wh "...`n"  
                fltmcCheck #function  
                    wh "...`n"  
                getDXDiag #function  
                    wh "...`n"  
                regLang #function  
                    wh "...`n"  
                autoRotate #function  
                getMISCLogs #function  
                    wh "...`n"  
                getDrivers #function  
                    wh "...`n"   
                getAV #function  
                    wh "...`n"            
                 }  
            
      
    #### RECEIVING JOBS SECTION ###...   
      
            #EventSearchJob  
            if($Global:EventsCollect -eq $True)  
            {          
                wh "`nWaiting for EventSearchJob to complete...`n"  
      
                Receive-Job -Name EventSearchJob -OutVariable eventSearch -Wait   
                $search = $eventSearch.Line  
            }  
      
      
            if($Global:SetupDiagCollect -eq $True)  
            {  
                #SetupDiagJob - Receive-Job  
                $stamp = (Get-Date -format "hh:mm tt")  
                wh "`nWaiting for SetupDiagJob to complete..."  
                wh "`nTime Stamp: $stamp"  
                wh "`nThis can take up to 10 minutes ..."  
      
                Do{  
                  SLEEP 15  
                    wh "."  
                    if((Get-Job -name SetupDiagJob).State -eq "Completed")  
                        { Receive-Job -Name SetupDiagJob  
                               wh "`nSetupDiag Completed!"                         
                            Break                      }  
                                    }Until($Cancel.SetupDiag -eq $True)  
                wh `n  
                                                   
                #Receive file and copy  
                Receive-Job -Name SetupDiagJob -Wait   
                Copy-Item $tempDir\Logs*.zip $tempDir\LOGS\SetupDiag-Log.zip  
                Copy-Item $tempDir\setupdiag*.log $tempDir\LOGS\  
                Remove-Item $tempDir\Logs*.zip  
            }  
      
           
            if($Global:UpdatesCollect -eq $True)  
            {  
                #GetUpdates Job via:  
                #UpdateHelper <--- GetUpdates Job has to finish first!  
                #Checking Status of GetUpdates Job...  
                wh "Checking Status of GetUpdates Job...`n"  
                If ((Get-Job -Name GetUpdates).State -eq "Failed")  
                    { wh "`nGetUpdates Job Failed!`n" }  
                        Else{  
                                Receive-Job -Name GetUpdates -wait  
                                Move $env:USERPROFILE\Desktop\WindowsUpdate.log $TempDir\LOGS\Windows-Update.log -Force  
                                wh "`n Writing Update Helper Info to UPDATE-ERRORS.TXT ... `n"  
                                UpdateHelper #run the update helper function  
                            }               
            } #End getting GetUpdates-job       
      
            #Finishing EventSearch  
            if($Global:EventsCollect -eq $True)  
                {  
                    writeSearch #function  
                }  
      
    #Wait on MSINFO...  
    if($Global:miscCollect -eq $True)  
    {  
        wh "`n Waiting for MSINFO32 to Complete ...`n"  
        do{ start-sleep 1 }  
        Until((get-process | select-string -Pattern "msinfo").Pattern -cne "msinfo")  
            werHint #function  
    }  
      
      
    if((Get-Host).Version.Major -cge 5) ##WIN7 Does not Support Transcript  
        {  
      
    Stop-Transcript   
      
            do{  
        start-sleep 1  
        }  
        Until((get-item $tempDir\LOGS\Event-Search.TXT).Length -cne 0)  
          
        }  
      
    wh "`nLog Collection Completed! `nLogs are available in %temp%\LOGS\`n"    
    wh "`nHit Any Key or Close ...`n"  
      
    Start-Sleep 1  
      
    Start Explorer.exe $explore  
      
    PAUSE  
      
    ## LOGS.PS1 1.6.3  ##     
    ## JOHNEM 8-2019 ##   
    ## EOF ##
      My Computer


  4. Posts : 48
    Windows 10
    Thread Starter
       #4

    Greetings!

    I performed all the suggested procedures, a directory and two compressed files were generated, I compressed the directory generated by the Power Shell script, and then I compressed the three together and uploaded it to my Dropbox.
    Follow the link...

    Dropbox - Thunderbird Windows Update Logs.zip - Simplify your life

    I changed the system language, made new logs and created a new file in Dropbox.

    Thank you.
    Last edited by Ro Wood; 28 Jun 2020 at 04:41.
      My Computer


  5. Posts : 1,867
    Windows 10 Pro 2004 20H1
       #5

    dalchina said:
    Use the Heidoc downloader to get build 1909..
    Rufus can also be used to download previous ISOs, as well as making bootable USB installation media.

    Rufus - The Official Website (Download, New Releases)
      My Computer


  6. Posts : 39,972
    windows 10 professional version 1607 build 14393.969 64 bit
       #6

    The logs could not be scanned.
    Please use English as the default language.
    See the tutorials in post #3.
      My Computer


  7. Posts : 35,000
    Win 10 Pro (1903) (2nd PC is 21H2)
       #7

    Have you considered an in-place upgrade repair install as post #2?
      My Computers


  8. Posts : 35,000
    Win 10 Pro (1903) (2nd PC is 21H2)
       #8

    Sorry chkdsk.

    a. was a disk check
    b. a file system check

    then an in-place upgrade repair.
      My Computers


  9. Posts : 48
    Windows 10
    Thread Starter
       #9

    @zbook

    I changed the system language, made new logs and created a new file in Dropbox.

    @dalchina

    I checked the disk and the file system.
    Using the iso the default windows installation screen is loaded does not say if it will keep my files, programs and settings, as the MediaCreationTool screen does ...
    How do you know if I'm not going to lose everything?
      My Computer


  10. Posts : 35,000
    Win 10 Pro (1903) (2nd PC is 21H2)
       #10

    How do you know if I'm not going to lose everything?
    If you log in then start the procedure, you are NOT doing a clean install.

    a. because I said so in bold because of the number of times this is asked, and to try to preclude this question yet again and save myself a lot of typing.
    b. because the tutorial on in-place upgrade repair says so
    c. would you ask the same question when applying a feature update to the next build? It's the same mechanism as that.
    d. from experience - mine and that of many others.

    All that said, it's a major change.

    Take precautions and as is so so tirelessly recommended on tenforums, create a current disk image just in case. E,g, Macrium Reflect (free) + large enough external storage.
      My Computers


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 03:10.
Find Us




Windows 10 Forums