Problems with SFC, Dism and Windows Update

Greetings!

In-place does not work, the installer goes all the way and Windows 10 fails to install.

The antivirus has been uninstalled.

1) For all steps / tests please post images into the thread:

Take Screenshot in Windows 10
https://support.microsoft.com/en-gb/...re-screenshots
How to Upload and Post Screenshots and Files at Ten Forums
For any problems posting images please use share links (one drive, drop box, or google drive)

2) For disk management > see instructions and tutorial > post a new image
a) widen each column as necessary so that the contents in the parenthesis are not cutoff
b) widen row disk 0 as necessary so characters are not cutoff

3) For Memtest86 > when available post the second test result images

4) Were the RAM modules replaced at any time?


5) Update the progress with each step in post #21 by displaying the step number

6) For in place upgrade failures:
a) post the error message and code
b) post a new V2
c) post a new powershell result share link using the script in post #3

Greetings!

Follow the new link for the new tests done.

Dropbox - Thunderbird Tests Results #2.zip - Simplify your life

As for the error that occurs when trying to perform the In-Place, not the error code, the Windows setup goes to the end when the phrase is displayed your computer will be restarted, but the computer will not restart and a window is displayed that says: installation failed and that's it.

- - - Updated - - -

Images of the In-Place failure.



Your PC will restart in a few moments


Windows 10 installation failure

I tried to run this script for Windows Update and it is against this Spupdsvc.exe file, does this have anything to do with it?

Script: Wufix.bat

sc config wuauserv start = auto

sc config bits start = auto

sc config cryptsvc start = auto

sc config trustedinstaller start = auto

net stop wuauserv

net stop bits

ren% systemroot% \ System32 \ Spupdsvc.exe Spupdsvc.old

cd% windir%

Ren SoftwareDistribution SoftwareDistribution.old

dism / online / cleanup-image / restorehealth

It gave error, first for not having found Spupdsvc.exe and then Dism.

-------------------------------------------------- ----------


C: \ windows \ system32> sc config wuauserv start = auto
[SC] ChangeServiceConfig SUCCESS

C: \ windows \ system32> sc config bits start = auto
[SC] ChangeServiceConfig SUCCESS

C: \ windows \ system32> sc config cryptsvc start = auto
[SC] ChangeServiceConfig SUCCESS

C: \ windows \ system32> sc config trustedinstaller start = auto
[SC] ChangeServiceConfig SUCCESS

C: \ windows \ system32> net stop wuauserv
The Windows Update service has not started.

For more help, type NET HELPMSG 3521.


C: \ windows \ system32> net stop bits
The Background Intelligent Transfer Service service has not started.

For more help, type NET HELPMSG 3521.


C: \ windows \ system32> ren C: \ windows \ System32 \ Spupdsvc.exe Spupdsvc.old
The system cannot find the file specified.

C: \ windows \ system32> cd C: \ windows

C: \ Windows> Ren SoftwareDistribution SoftwareDistribution.old
A file with the same name already exists
or the file cannot be found.

C: \ Windows> dism / online / cleanup-image / restorehealth

Deployment Image Maintenance and Management Tool
Version: 10.0.18362.1

Image Version: 10.0.18363.836

[===== 10.0%]

The window closes on approximately 22% of the Dism.

- - - Updated - - -

Greetings!

I gave up and did a clean install.
No error codes during installation, all as expected.
After the installation was finished, all the drivers were installed, I started to install the updates, without error codes the system left to reboot, and that's when this new chapter starts, at 7% of the update the notebook restarts and when it returns a screen says that the update was not successful, it restarts again and then the phrase is displayed, do not turn off the updates are being undone and it loads the system and when entering the system and go to the settings screen, in updates the error 0x80070003 is displayed, well I'm hot-headed ...

Does anyone have any ideas?..

C: \ Windows \ system32> SFC / Scannow

Starting file verification. The process will take a few minutes to complete.

Starting verification phase of system verification.
100% verification completed.

Windows Resource Protection found no breaches of integrity.

C: \ Windows \ system32> DISM / Online / Cleanup-Image / ScanHealth

Deployment Image Maintenance and Management Tool
Version: 10.0.18362.1

Image Version: 10.0.18363.418

[========================== 100.0% ======================= =====] No component repository corruption detected.
The operation was successfully completed.

C: \ Windows \ system32> DISM / Online / Cleanup-Image / RestoreHealth

Deployment Image Maintenance and Management Tool
Version: 10.0.18362.1

Image Version: 10.0.18363.418

[========================== 100.0% ======================= =====] Restore operation completed successfully.
The operation was successfully completed.

C: \ Windows \ system32>

Greetings!
After trying and trying, I was unable to solve anything with the Windows installation, leaving no other path but formatting, followed by a clean installation.
Everything went back to normal after installing build 1909 on 7/3 and yesterday 7/26 updating via Windows Update for 2004.
I am grateful to all those who tried to help me with my problem, which proved to be insoluble and I just didn't choose to format it because I didn't have enough disk space to store all my files since my USB disks are full, requiring the purchase of a new unit to carry out this operation.
Everything went well, even the Apps that I was afraid of losing because they were no longer available for download on the Microsoft Store page, I managed to recover with the help of Tenforums members, which can be read on this page, Reinstall SpotBright and DailyPic ...

I look for any questions, but I hope it will take a long time for this to happen. ha ha

Thank you all.