Windows 10: BIOS and DOCP (XPM on some)

  1.    26 Mar 2018 #1

    BIOS and DOCP (XPM on some)


    I emailed asus about their Prime 350+ MB and the new chips Corsair Vengeance 3200mhz (2 x 8GB) and they told me the reason it was still running on 2133mhz as its the normal speed for the MB. If I wanted to up to 3200mhz I had to activate something known as DOCP on AI page in BIOS, so I did. Saved and exit = reboot.

    At reboot I got 2-3 bleeps each time as the pc tried to reboot 2-3 times. Then I got a b/w screen telling me it was going to load in safe mode. I pressed noted F1 key and entered BIOS again and checked setting, still on 3200mhz so left BIOS without saving (it was already saved) and it booted into windows with all access apparent.

    I dont pretend to understand much of this and probably never will, so later, I will shut down and see if pc runs 'normally'
      My ComputerSystem Spec


  2. Posts : 11,901
    Windows 10 Pro X64
       26 Mar 2018 #2

    While the RAM is rated to run 3200, it may require slight adjustments to the DRAM Voltage and Vccio and System Agent Voltages. That is how it is for Intel, I would wait for some Ryzen users to respond too like @CountMike
      My ComputerSystem Spec

  3.    26 Mar 2018 #3

    Chip is Ryzen quad; see specs. I adjusted DOCP but did not reboot pc until a few mins ago, it opened normally. In the a.m. if I remember, I will open BIOS and see if setting have remained 3200mhz.

    dude, so what voltage should I see if DRAM is running on/set to????

    with a name like dude, you've got to be a Texican!!

    Once upon a time I would not touch BIOS with a 200 mile pole!! Its a lot more user friendly than it was 3000 years ago
      My ComputerSystem Spec


  4. Posts : 11,901
    Windows 10 Pro X64
       26 Mar 2018 #4

    Yep, Im in Texas..not sure about AMD voltages as Im on Intel
      My ComputerSystem Spec

  5.    27 Mar 2018 #5

    elbmek said: View Post
    I emailed asus about their Prime 350+ MB and the new chips Corsair Vengeance 3200mhz (2 x 8GB) and they told me the reason it was still running on 2133mhz as its the normal speed for the MB. If I wanted to up to 3200mhz I had to activate something known as DOCP on AI page in BIOS, so I did. Saved and exit = reboot.

    At reboot I got 2-3 bleeps each time as the pc tried to reboot 2-3 times. Then I got a b/w screen telling me it was going to load in safe mode. I pressed noted F1 key and entered BIOS again and checked setting, still on 3200mhz so left BIOS without saving (it was already saved) and it booted into windows with all access apparent.

    I dont pretend to understand much of this and probably never will, so later, I will shut down and see if pc runs 'normally'
    DOCP is AMD "speak" for XMP (Intel invention). It should read XMP profile in RAM controller and set it accordingly.
    Under DOCP heading you should have another "Memory frequency" with which you can alter the RAM frequency further.
    Click image for larger version. 

Name:	170916112102.jpg 
Views:	1 
Size:	275.9 KB 
ID:	182461
    Behavior you described is called "Memory training" and is usual when changing memory settings. To make sure what and how memory is running, you can use CPU-Z CPU-Z | Softwares | CPUID under headings Memory and SPD.
      My ComputersSystem Spec


  6. Posts : 3,432
    3-Win-7Prox64 2-Win10Prox64
       27 Mar 2018 #6

    Hi,
    1.525v is a lot of voltage @CountMike :)
      My ComputersSystem Spec

  7.    27 Mar 2018 #7

    ThrashZone said: View Post
    Hi,
    1.525v is a lot of voltage @CountMike :)
    That was just a first time I started setting new BIOS, stupid automatic voltage control on first BIOS version. Now it's staying at ~1.375v @ 3.9GHz and that's only when LLC5 kicks in at full load. Normally voltage stays at about 1.325v. Nothing my cooler can't handle at low '60c.
      My ComputersSystem Spec

  8.    30 Mar 2018 #8

    I have reset BIOS to default and setting returned to auto. Reason being I started getting crashes and screen locks and staggering frames. ASUS I suspect have not been fully explanatory and I began to think I might need to upgrade the MB but decided it would be best to go backwards, so all is reset to 2133mhz. The chips I took out and went to exchange them only to find damn place (box.co.uk) was shut for Easter. Chips back in but running 2133mhz, the pc seems happier. Fallout4 was doing all the above mentioned but now its running smoothly.

    CM: on your diagram which is identical to mine, the DDRAM was set under DCOP at 3200mhz; the MB still said 2133mhz. I dont recall voltage, having not touched it. As far as I can recall the CPU is 3200mhz, so two components seems not to tie in with the MB mhz???
      My ComputerSystem Spec

  9.    30 Mar 2018 #9

    This is how it's set up now:
    Click image for larger version. 

Name:	bios1.jpg 
Views:	1 
Size:	148.7 KB 
ID:	182834
    And after some more settings:
    Click image for larger version. 

Name:	image.png 
Views:	9 
Size:	73.4 KB 
ID:	182835
    Is result.
      My ComputersSystem Spec


 

Related Threads
Solved Can't get into the Bios in Performance & Maintenance
I have a Gateway NE56R52u that I upgrade from Windows 7 Home to Windows 10 Home and I can't get into the Bios. I've been on google all afternoon and tried everything but no luck. I have a HP desktop that I upgrade from Windows 7 Pro to Windows 10...
bios help in Installation and Upgrade
hi,guys my laptop is a lenovo g50-30, I want to do a fresh install of windows 10 using a DVD, I note in the bios menu there is (UEFI ) and (legacy support) not sure what this is? can the laptop run in (UEFI )mode or(legacy support) if so...
Bios Help in Drivers and Hardware
Hello All Insider users :) I cannot access to the Bios to make some boot sequence order changes. The usb hub doesn't let the computer to restart any time needed because sequence order is wrong. Can some one help me please ? Thank you.
Bios in General Support
Hi, In case Windows fails to load, can you still enter BIOS in order to change boot device priority etc. Yes or no. Thanx. Edwin
Solved Bios again in Drivers and Hardware
Hi, Does Bios get automatically updated like Windows or do I have to do it manually? If so, how do I check if my Bios needs upgrading? I see the version/date, American Megatrend inc v10.7, 22.07.2014, but have no idea whether it is outdated or...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 13:21.
Find Us