Windows 10: Add OEM Provisioning Package to clean install Solved

Page 1 of 2 12 LastLast
  1.    25 Mar 2017 #1

    Add OEM Provisioning Package to clean install


    I have the following OEM customization and provisioning package on my C: drive:

    Click image for larger version. 

Name:	Capture.JPG 
Views:	54 
Size:	49.9 KB 
ID:	126687

    Where would I copy these files to the standard Windows 10 installation USB flash drive to have them applied during a clean install of Windows 10?

    My current install is a clean install without the customizations or provisioning package applied, the C:\Recovery folder was retrieved from an image backup I made before doing the current clean install.

    @Kari <attention getter. You're probably the everything Windows recovery and installation expert that knows the answer!
      My ComputerSystem Spec


  2. Posts : 6,412
    10 Home x64 (1709) (10 Pro on 2nd pc)
       25 Mar 2017 #2

    NavyLCDR said: View Post
    Where would I copy these files to the standard Windows 10 installation USB flash drive to have them applied during a clean install of Windows 10?
    I too will await an expert opinion with interest but as I undertand it, if you make a Recovery Drive and tick the box for 'include system files' the provisioning package gets copied too. The recovery drive should then have everything needed to do a 'factory reset' clean install to manufacturer's original condition.
      My ComputersSystem Spec

  3.    25 Mar 2017 #3

    Bree said: View Post
    I too will await an expert opinion with interest but as I undertand it, if you make a Recovery Drive and tick the box for 'include system files' the provisioning package gets copied too. The recovery drive should then have everything needed to do a 'factory reset' clean install to manufacturer's original condition.
    Yes, I thought about that. I might give that a go in the meantime.
      My ComputerSystem Spec


  4. Posts : 13,756
    Windows 10 Pro
       25 Mar 2017 #4

    Bree said: View Post
    I too will await an expert opinion with interest but as I undertand it, if you make a Recovery Drive and tick the box for 'include system files' the provisioning package gets copied too. The recovery drive should then have everything needed to do a 'factory reset' clean install to manufacturer's original condition.
    Nothing to add to that.
      My ComputerSystem Spec

  5.    25 Mar 2017 #5

    Kari said: View Post
    Nothing to add to that.
    So, I can't add it to the standard Windows 10 installation USB flash drive? I have to do it via creating a recovery drive?
      My ComputerSystem Spec


  6. Posts : 13,756
    Windows 10 Pro
       26 Mar 2017 #6

    NavyLCDR said: View Post
    So, I can't add it to the standard Windows 10 installation USB flash drive? I have to do it via creating a recovery drive?
    If you have a provisioning package as standard provisioning package file (.ppkg) you can add it to an offline image (install.wim) with DISM. Simple straight forward instructions: https://blogs.msdn.microsoft.com/bea...ge-using-dism/
      My ComputerSystem Spec

  7.    26 Mar 2017 #7

    Thank you for all the help and info!
      My ComputerSystem Spec


  • Posts : 1,981
    Windows 3.1 to Windows 10
       26 Mar 2017 #8

    If it was Recovery Media > you would copy those Folders into the SOURCES Folder
    Along with the Factory Install.wim or Install.swm(s) from the Image Partition
    And Along with the Factory WinRE.wim from the Recovery Tools Partition (Renamed Boot.wim)
      My ComputerSystem Spec

  •    26 Mar 2017 #9

    Kyhi said: View Post
    If it was Recovery Media > you would copy those Folders into the SOURCES Folder
    I looked and they are on the recovery drive I created from the built-in Windows create recovery media function. Going to do the recovery later this morning and see what I get as a result. I'm usually not a big fan of factory recoveries but I just bought a refurbished laptop that came with Windows 10 installed by the refurbishing company but has no OEM support of Windows 10 from HP. They did a bad job of it, though. Windows 10 was installed in legacy CSM mode instead of UEFI and when I went to install the second HDD in the laptop I found that the SSD had one screw not tightened at all (luckily it is in a caddy with captive screws) and the internal door over the SSD caddy was also not screwed down (again, captive screw there, thank goodness).

    So, I'm just curious if the provisioning package had some drivers in it that would make all the function keys work which didn't work after I did a clean install in UEFI mode.
      My ComputerSystem Spec


  • Posts : 1,981
    Windows 3.1 to Windows 10
       26 Mar 2017 #10

    make an Image of your clean Install..
    Then double click the apps.ppkg to install factory customizations...

    see if that works...

    that ppkg will get applied if included in the c\recovery folder when doing a reset
    and will be copied to recovery media - using recovery media tool

    all the other files in those folders - are for Factory OEM Recovery, partitions, customizations, etc..

    What you want to KEEP and USE is the Factory WinRE.wim (Recovery Media - Boot.wim)
    As it has been customized with boot and system drivers.. vs Clean Install winre.wim
      My ComputerSystem Spec


  •  
    Page 1 of 2 12 LastLast

    Related Threads
    Provisioning package fails to install in Installation and Upgrade
    Hello I have setup a test machine with all the settings and apps I need, I have then created a provisioning package Called 'capturedSettings' using the ICD but when I try to install it I get the following error I use the following tutorial on...
    Installation & Upgrade Create Provisioning Package in Windows 10 in Tutorials
    Create Custom Provisioning Package used to Reset Windows 10 or Create Recovery Drive If you're having problems with Windows 10 on your PC, in some cases you may want to reset it or use a recovery drive which you have created. If you have...
    Hello. I have upgrated my ASUS ROG G55W laptop to WIndows 10, and ATK Package ver 1.0.0017 is installed by default. After checking some of the new stuff, I found a "ASUS Welcome" app. In this app some updates are poposed, and I found a newer ATK...
    When I upgraded to windows 10 from windows 7, it worked fine for the next few hours then i couldnt acess the log in screen it was just stuck on the slider and then it flickers. tried to trouble shoot, system restore, clean installed (using...
    Solved Best codecs package to install? in Installation and Upgrade
    What's the best video/audio codecs package to install for Window 10? I can't even get the "get started" video to play. Just black, and some of web video black as well.
    Our Sites
    Site Links
    About Us
    Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

    Designer Media Ltd
    All times are GMT -5. The time now is 10:30.
    Find Us