Windows 10: Fixing an inadvertent dual boot of Windows 10 Solved

  1.    15 Dec 2015 #1

    Fixing an inadvertent dual boot of Windows 10

    My original boot drive for this computer was failing. Apparently a memory chip had also gone bad, which certainly complicated things further. (I suffered through a day with one blue screen of death after another -- my computer could not stay booted for longer than 30 seconds before it would crash with a number of different error messages. Once I could get into safe mode, it was stable for a bit longer.) At any rate, I made a USB install disk for Windows 10 on another machine, but the only way I could get my computer to boot from the USB was to get to Windows first and THEN go into recovery mode and tell it to boot from the USB drive. Once I did that, I installed a fresh version of Windows 10 onto a new, much larger drive.

    Eventually I want to get rid of the old drive, since it's been unreliable (damaged sectors and files, can't be repaired through chkdsk, etc.). In fact, I'm ready to reformat it now. But I'm afraid that my computer is still using the old drive for booting and that Windows 10 -- when it was installed onto the new drive -- didn't install the necessary boot partition for my new drive to boot as a solo operation.

    I think this because my computer will not boot unless I force it to go to the BIOS first and then exit. If I don't go to the BIOS, it just sort of hangs there with no activity and never makes it as far as a Windows logon screen (or even a choice of boot options). If I press F10 to force it to bring up the BIOS set-up menu, once that loads I just need to exit without making any changes and then the computer will boot into the new Win10 partition on the new drive.

    When I look at disk management, it shows me one large partition for my new drive which is defined as "Healthy (Boot, Page File, Crash Dump, Primary Partition)". The old failing drive is subdivided into 6 partitions, 3 of which are labeled Recovery, one is Primary, and the other is the EFI System Partition. I'm thinking the EFI System Partition is what needed to be on my new drive.

    How do I fix this? Or do I need to fix this?

    This has been a saga of one headache after another... the failed boot drive, the failed memory, having to refresh Windows again on the newer hard drive (because apparently the memory fault corrupted both my Windows 10 new installation as well as totally trashed an external hard drive which was previously fine). So I want to make sure I don't cause any further headaches for myself by doing the wrong thing. If I can use the Windows Disk Management tool to fix things, I'll need step-by-step instructions since I've never partitioned (or re-partitioned) a hard drive before.

    Thank you in advance for any help you can give me.
      My ComputerSystem Spec

  2.    15 Dec 2015 #2

    I would install MiniTool Partition Wizard Free. Use that to shrink your Windows 10 partition on the new hard drive and create an empty space equal to the partition size of the EFI system partition on the old hard drive. Copy the EFI system partition from the old hard drive to the newly created empty space on the new hard drive. Make sure it gets marked as active on the new hard drive. After partition wizard finishes everything then just disconnect the cable from the old hard drive and see if your computer will boot to the new hard drive installed alone.

    An alternative method would be to install EasyBCD. There is a function in EasyBCD to move the boot files to a different hard drive/partition. You might be able to just point the new BCD location to the Windows partition on the new hard drive. Then disconnect the cable from the old hard drive and see what happens. I don't like having my boot files on my Windows partition myself, but that is just my personal preference.

    Best Free Partition Manager for Windows | MiniTool Partition Free

    EasyBCD - NeoSmart Technologies
      My ComputerSystem Spec

  3.   My ComputerSystem Spec

  4.    18 Dec 2015 #4

    Thank you, NavyLCDR, and thank you, whs, for both your suggestions to my dilemma. I've been offline for several days while my computer got sorted out and I've finally got a bare minimum Windows 10 installation completed. But at last it's working, and -- glory be! -- it's actually booting from my new hard drive now.

    I tried to use the EasyBCD first, but got an error message and was unable to do anything with it. I can't recall now what the exact message was -- something about the drive being locked, maybe? -- but even though it didn't help in this particular situation it seems like a good tool to know about for future reference.

    I did use the Mini Tool Partition Wizard Free to split my drive, but in the end I just didn't trust my failing hard drive to have reliable partitions to copy from so I opted to do yet another clean install of Windows 10. This time round I was greatly aided by the TenForums tutorial, in which the #13 section for those with UEFI systems was particularly helpful.

    I'm a little amazed at Windows 10's express installation that helped get me in this mess in the first place. It seems to me that an express set-up on a new drive ought to assume both that (1) the user doing the installation is likely more of a novice; and (2) if you're going to put Windows 10 on a completely new drive, the chances are extremely high that you'll want to boot off this new drive. Perhaps no one has looked too closely at the installation routines since the technical preview edition of Windows (when it was a lot more likely that people actually did want dual boot systems).

    At any rate, at last I seem to have a functioning system again. Now it's just the long road to rebuilding my computer -- reinstalling all my software and re-customizing all my programs... (sigh)

    Thanks again for your help! And best wishes for the holidays and the coming New Year.

      My ComputerSystem Spec


Related Threads
Today I installed Windows 10 on my machine (ASUS N55SF laptop) for the first time on a separate hard drive. Now I have Windows 7 on my main hard drive and Windows 10 on my new drive (the latter being an SSD one). After installing Windows 10, I got a...
Windows 10 & XP dual boot. Best way? in Installation and Upgrade
Hi, I have a PC running Windows 7 only at the moment. I want to end up with it running Windows XP (as default) and Windows 10 as a dual boot. What's the best way? I have an unused XPx64 installation disc and I have used "Windows 10...
I installed the 10 tech preview along side my win 7 ultimate, I reinstalled, the Windows 7 side of the HDD because after however many years the OS had a LOT of clutter, and even though windows update was a nightmare I finally got all the updates...
Recently I played around with dual booting Linux Mint on my system. I decided that I would delete it for the present as I have other things to focus on. However, after deleting partitions and fixing my MBR to only boot windows my UEFI BIOS still...
My laptop has dual boot - Windows 7 and Windows 10. My Win7 environment is my main working environment with lots of programs installed and important files. I installed the Win10 environnment just to play around with 10 during the technical...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 05:51.
Find Us