OK, I did as you said, the 0xc0000098 error came up with BIOS set to ACHI mode, the 0xc0000225 came up with BIOS set to IDE mode...
- - - Updated - - -
How do I run this file and what do I look for...
- - - Updated - - -
I ran it and found the files in the TEMP folder on the RamDrive!? Here ya go!
The following is the output from the OP's Windows PE.
Code:Microsoft DiskPart version 10.0.19041.1 Copyright (C) Microsoft Corporation. On computer: Win10XPE Disk ### Status Size Free Dyn Gpt -------- ------------- ------- ------- --- --- Disk 0 Online 447 GB 1024 KB Disk 1 Online 29 GB 0 B Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- Volume 0 C MAGICTHIGHS NTFS Partition 446 GB Healthy Volume 1 E RESERVED FAT32 Partition 451 MB Healthy Volume 2 Y FAT32 Removable 29 GB Healthy Disk 0 is now the selected disk. KINGSTON SH103S3480G Disk ID: 000163B6 Type : SATA Status : Online Path : 0 Target : 0 LUN ID : 0 Location Path : PCIROOT(0)#PCI(1F02)#ATA(C00T00L00) Current Read-only State : No Read-only : No Boot Disk : No Pagefile Disk : No Hibernation File Disk : No Crashdump Disk : No Clustered Disk : No Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- Volume 0 C MAGICTHIGHS NTFS Partition 446 GB Healthy Volume 1 E RESERVED FAT32 Partition 451 MB Healthy Partition ### Type Size Offset ------------- ---------------- ------- ------- Partition 1 Primary 446 GB 31 KB Partition 2 Primary 451 MB 446 GB Partition 1 is now the selected partition. Partition 1 Type : 07 Hidden: No Active: Yes Offset in Bytes: 32256 Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- * Volume 0 C MAGICTHIGHS NTFS Partition 446 GB Healthy Partition 2 is now the selected partition. Partition 2 Type : 0C Hidden: No Active: No Offset in Bytes: 479628099584 Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- * Volume 1 E RESERVED FAT32 Partition 451 MB Healthy Disk 1 is now the selected disk. Specific STORAGE DEVICE USB Device Disk ID: 00005BFC Type : USB Status : Online Path : 0 Target : 0 LUN ID : 0 Location Path : UNAVAILABLE Current Read-only State : No Read-only : No Boot Disk : No Pagefile Disk : No Hibernation File Disk : No Crashdump Disk : No Clustered Disk : No Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- Volume 2 Y FAT32 Removable 29 GB Healthy Partition ### Type Size Offset ------------- ---------------- ------- ------- Partition 1 Primary 29 GB 512 B Partition 1 is now the selected partition. Partition 1 Type : 0C Hidden: No Active: Yes Offset in Bytes: 512 Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- * Volume 2 Y FAT32 Removable 29 GB Healthy =============================================================================== =============================================================================== The boot configuration data store could not be opened. The requested system device cannot be found.
Agree! Although, my daughter's computer had the same problem a while ago. I took the hard drive out of here computer and put it in my desktop computer. I then used the dism command to "Revert Pending Actions". After that I was able to boot her hard drive in my desktop computer, do all the updates, then re-install the hard drive back into her computer. But that is certainly not guaranteed to work in this case.
Code:The boot configuration data store could not be opened. The requested system device cannot be found.
Code:Windows resource protection found corrupt files and was unable to repair some of them.
Which of these were found:
Code:%systemroot%\Minidump %systemroot%\memory.dmp %systemroot%\LiveKernelReports %windir%\Logs\CBS\CBS.log C:\WINDOWS\Logs\CBS\CBS.log C:\Windows\memory.dmp C:\Windows\Minidump C:\Windows\LiveKernelReports
Consider:
Custom Install Windows 10
How to Restore Files from Windows.old Folder in Windows 10
Clean Install Windows 10
Do what?
You wrote you have a Win PE. Is it from the Win 10 installation drive?
Do you have a data backup or a external HDD?
Clean Install
WinPE is installed on a 32Gb USB3 Memory Stick... You're talking about the Users Folder... how does that work... will all my installed Desktop and Start Menu Shortcuts still work...
- - - Updated - - -
Is there anyway I can do an inplace upgrade...
- - - Updated - - -
@zbook, can't find those files... anyway I can create them...
You didn't answer if you have an external HDD to store the backup from C:\users"name"
WinPE is very generic. There are some with a lot of tools and graphic interface and you also has the Win 10 installation that loads a WinPE to install or do maintenance.
A clean install you start from scratch and you will need to reinstall all your programs.
To do an in place upgrade you must be under working windows. Not your case.
There is a almost clean install over an existing installation. How big is your drive and how much free space you have on it?
An in place upgrade cannot be performed from Windows PE, RE, or safe mode.
It can be performed from normal or clean boot.
These text files should be available:
%windir%\Logs\CBS\CBS.log
or
C:\WINDOWS\Logs\CBS\CBS.log
Quote