Your Device Is not Ready Vs 2004

Page 1 of 12 12311 ... LastLast

  1. Posts : 3,643
    Windows 11 Pro 64 Bit 21H2
       #1

    Your Device Is not Ready Vs 2004


    I have 2 desktop computers. Speccy reports on each one attached.
    The Old computer, computer A is about 10 years old. The new computer, Computer B is about 6 months old. I made an image of Computer A when it was on Windows 10 1903. I restored this image to Computer B, I then upgraded both computers to 1909 with no issues using the same ISO image file. Both computer working flawlessly.
    I am trying to install 2004. Using the latest ISO image downloaded from the Microsoft site v 34201 3 other laptops have been upgraded with this image with no problem and 2 other laptops have had a Clean install with this same ISO image with no issues.
    Computer A has a message in Windows Update that says, Your Device Is Not Ready. (See attached) Computer B does not have this message. Using the same ISO image 2004 as other computers that were successful, upgrading each desktop, both fail with the error
    0xC1900101-0x40017 Installation failed in the Second_Boot phase
    I have Updated each nVidia driver from the nVidia page to the latest driver for each computer. There is 104GB Free space on each C: drive.
    I have also done the following
    All Windows Updates
    Disable Memory Integrity
    Use DISM Tool and SFC /scannow
    No Yellow flags in Device Manager. All drivers updated to latest Gigabyte drivers for these boards.

    Computer A http://speccy.piriform.com/results/h...emGq3rdE8OWxKj
    Computer B http://speccy.piriform.com/results/M...tsBh6gohMUZ1xm

    I do not know what Microsoft is waiting for and what it needs to do to Computer A.to make it Ready. I also don't know what to do with Computer B to do the Upgrade. Any help would be welcomed.
    Attached Thumbnails Attached Thumbnails Your Device Is not Ready Vs 2004-2020-06-20-not-ready.png  
      My Computer


  2. Posts : 19
    Windows 10 Professional Version 10.0.18363 Build 18363
       #2

    I'm no expert, but I've been reading a lot about Windows10 2004. From what I understand, 2004 still has some issues, and so MS is withholding the update for machines it knows aren't going to be compatible. Once they get the bugs ironed out, you'll get the upgrade. Note in their message to you "there's nothing you need to do at this time".

    Now for the truly knowledgeable folks to weigh in....
      My Computer


  3. Posts : 39,953
    windows 10 professional version 1607 build 14393.969 64 bit
       #3

    The upgrade error code: 0xC1900101-0x40017 is typically caused by a problematic driver.

    Please run V2 and upload directly into this thread:
    BSOD - Posting Instructions

    Run this script and post a share link into the thread:

    Code:
    function wh   
        {  
            Param ( [parameter (Mandatory = $true)][string]$txt )  
            Write-Host $txt -ForegroundColor Green -BackgroundColor Black -NoNewline  
            ##Example usage wh "Alias for `n Write-Host"  
      
        } ## End function wh  
      
      
    function StartScript   
        {  
            ##Locating Temp Dir and writing Transcript  
            $global:tempDir = [System.IO.Path]::GetTempPath()   
            MD $tempDir\LOGS -EA SilentlyContinue   
            CD $tempDir\LOGS  
            $txtCount = Get-Item $tempDir/LOGS/*.TXT -EA SilentlyContinue  
            if((Get-Host).Version.Major -cge 5) ##WIN7 Not Supported  
                {  
                    if($txtCount.Count -cge 1)   
                    {Start-Transcript -Append -Path $tempDir/LOGS/Event-Search.TXT}   
                    Else{Start-Transcript -Path $tempDir\LOGS\Event-Search.TXT}   
                }  
      
            $global:explore = $tempDir + "LOGS\"  
            $global:Ver = "1.6.3"  
            wh "`nLog Collection... (V$Ver)`n"  
      
            #clearing previous actions  
            Stop-Job *  
      
            #Initialize CheckBox Vars to $True/$False  
                $Global:EventsCollect = $true; $Global:SetupDiagCollect = $true  
                    $Global:UpdatesCollect = $true; $Global:WLANCollect = $true  
                        $Global:PowerCollect = $true; $Global:GPCollect = $true  
                            $Global:miscCollect = $true; $Global:bingCollect = $true  
                                $Global:eventOut = $false        
            #Clear Jobs  
            Stop-Job *  
            Remove-Job *  
                                              
        } ## End function Start-Script  
      
      
    function SetupDiagFunc  
        {  
            wh "`n Grabbing SetupDiag.exe ..."       
            Invoke-WebRequest https://go.microsoft.com/fwlink/?linkid=870142 -OutFile $tempDir\SetupDiag.exe -TimeoutSec 3 -UseBasicParsing  
                #check for successful download  
                if((Get-Item $tempDir\SetupDiag.exe).length -gt 100000)  
                    {  
                      wh "`nSuccessful DL!"  
                      wh "`n Invoking SetupDiag.exe ..."  
                      $SetupDiag = {CMD.EXE /C "%temp%\setupdiag.exe /Verbose /Output:%temp%\SetupDiag-Log.txt"}  
      
                      ## Kick-Off SetupDiagJob  
                      Start-Job -Name SetupDiagJob -ScriptBlock $SetupDiag                     
                      
                    }Else{Write-Host "`nDownload of SetupDiag.exe Failed!" -BackgroundColor RED }  
      
        } ## End Function SetupDiagFunc  
      
      
    function EventSearch  
        {  
        wh "`n Starting EventSearch Job-Function ...`n"  
        ## Gathering Events from System using Get-WinEvent via Job  
        $EventSearchJob =   
            {  
            $evtPaths = Get-Item C:\Windows\System32\Winevt\Logs\*.evtx -Exclude "*PowerShell*",   
                "*known folders*" | Select-Object FullName  
            $i = $evtPaths.Count  
      
            $x = 0 ##For 1st Loop do Until x = i  
            $events = @()  
            $gatherEvents = @()  
            $eventsArray = @()  
            $searchResult = @()  
            $MaxEvents = 99  
      
            #Loading/Gathering Events Loop...  
            do {  
           
                ##Getting Events w/ Get-WinEvent         
                $gatherEvents = Get-WinEvent -Path $evtPaths[$x].FullName -MaxEvents $MaxEvents -EA SilentlyContinue  
                $events = $events + $gatherEvents             
      
                $x++  
                  
                }  
                 Until ($x -eq $i)      
      
            $x = $x +1 ##Total Events Found!  
              
            $eventsLength = $events.Length ##Total events catalogged!  
              
            $xx = 0  
                   
            # Write Event Properties to a row and roll it out - Collapsing Array ...   
            do {  
                   $date = $events[$xx].TimeCreated | Get-Date -Format "yyyyMMdd".ToString() -EA SilentlyContinue ##EA SC for Blank Entries  
                      
                    $eventRow = new-object PSObject -Property @{  
                    Date = $date;  
                    Id = $events[$xx].Id;  
                    Level = $events[$xx].LevelDisplayName;  
                    Provider = $events[$xx].ProviderName;  
                   Message = $events[$xx].Message;  
                    }  
      
                    $cRow = $date + " " + "ID:" +  $events[$xx].Id + " " + "Level:" + $events[$xx].LevelDisplayName + " " + "Provider:" + $events[$xx].ProviderName + " " + "Message:" + $events[$xx].Message   
                    $eventsArray += $cRow  
                   
                    $xx++  
                    $d++  
            }  
            Until ($xx -eq $events.Length)  
     
            ##Looking for patterns error or fail in $eventsArray  
            $search = $eventsArray | Select-String -pattern ("error|fail") 
     
            Return $search ## | Write-Output ##Output for job  
      
            } ## End $EventSearchJob  
      
        Start-Job -Name EventSearchJob -ScriptBlock $EventSearchJob  
      
        } ## End function Event-Search  
      
      
    function writeSearch  ##   
        {  
            ##Event Logs Cont.  
            MD $tempDir\LOGS\EVTX\ -EA SilentlyContinue 
     
            ##output to file  
            $search | Group-Object | Sort-Object Count -Descending | Format-Table Count, Name -Wrap > TOP-ERRORS.TXT  
            $search > $tempDir\LOGS\SEARCH.TXT  
      
        if($Global:eventOut -eq $True)  
            {  
            $search | Group-Object | Sort-Object Count -Descending |   
                Select-Object -Property Count, Name | Out-GridView -Title "Top `"Errors`" via EVTX - V-$Ver"  
            }  
      
            wh "`n Collecting Matching EVTX Entries ...`n"     
            #Collecting all prev matching EVTX  
            #$evtx = Get-ChildItem C:\Windows\System32\Winevt\Logs\*.evtx  
            $evv = 0  
                      
               $providerName =   
                   (($search | Select-String "Provider:.*Message:").Matches.Value -Replace   
                          " Message:", "" -Replace "Provider:", "" | Group-Object ).Name  
                  
                #Converting Provider Name to Log Name                 
                $providerName = (($providerName | ForEach-Object {Get-WinEvent -ProviderName $_ -MaxEvents 1 -EA SilentlyContinue}).LogName | Group-Object).Name     
                   $providerName = $providerName -replace "Microsoft.", ""  
                      $providerName = $providerName -replace "Windows.", ""  
                         $providerName = $providerName -replace "`/.*$", ""  
                               
                               
                             $evtx = $providerName | foreach{Get-ChildItem "C:\Windows\System32\winevt\logs\*$_*"}  
      
                    Do{  
                        COPY $evtx[$evv].PSPath $tempDir\LOGS\EVTX\ 
                           $evv++  
                      }  
                      Until($evv -eq $evtx.Count)  
      
        } #End function writeSearch  
      
      
    function GetUpdates  
        {  
            wh "`n Starting Get-WindowsUpdateLog Job-Function ...`n"  
            $updateJob = {get-WindowsUpdateLog}  
             
            if((Get-Host).Version.Major -cge 5) ##Modern Gatherer  
            {  
                Start-Job -Name GetUpdates -ScriptBlock $updateJob  
            }  
              
            ##Legacy Gatherer  
            CP C:\Windows\WindowsUpdate.log $tempDir\LOGS\WindowsUpdate.log  
      
            ##Installed-Updates/Packages 
            Get-WmiObject win32_quickfixengineering > $tempDir\LOGS\Installed_Updates.TXT  
            Get-WmiObject Win32_OperatingSystemQFE >> $tempDir\LOGS\Installed_Updates.TXT  
        DISM /Online /Get-Packages /Format:Table >> $tempDir\LOGS\Installed_Updates.TXT 
      
        } ## End function Get-Updates  
      
           
    function PrinterCheck  
        {  
            wh "`n Getting Printer Information ..."  
            get-printer | ft Name, ComputerName, Type, DriverName, PortName, Datatype, Location, DriverName > $tempDir\LOGS\Printers.TXT  
            get-printerDriver | fl >> $tempDir\LOGS\Printers.TXT  
            Get-ChildItem -Recurse Registry::"HKLM\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows NT x86\Drivers" | Out-File $tempDir\LOGS\Printers.TXT -Append  
            Get-ChildItem -Recurse Registry::"HKLM\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows x64\Drivers" | Out-File $tempDir\LOGS\Printers.TXT -Append  
            Get-ChildItem -Recurse Registry::"HKLM\SYSTEM\CurrentControlSet\Control\Print\Monitors" | Out-File $tempDir\LOGS\Printers.TXT -Append  
            write-output "## CBS ntprint CHECK ##" >> $tempDir\LOGS\Printers.TXT  
            $cbsCheck = (Get-ChildItem C:\Windows\Logs\CBS\*cbs* -Recurse | select-string -Pattern "E_INVALIDARG in eventsXml.*Microsoft-Windows-PrintService")  
            if($cbsCheck.Count -eq 0){Write-Output "## NO MATCHES IN CBS ##" >> $tempDir\LOGS\Printers.TXT} Else{$cbsCheck | Group-Object  >> $tempDir\LOGS\Printers.TXT}  
            write-output "## ntprint.dll CHECK ##" >> $tempDir\LOGS\Printers.TXT  
            (Get-ChildItem C:\Windows\System32\ntprint.dll).VersionInfo | ft -AutoSize >> $tempDir\LOGS\Printers.TXT  
            (Get-ChildItem C:\Windows\SysWOW64\ntprint.dll).VersionInfo | ft -AutoSize >> $tempDir\LOGS\Printers.TXT  
      
        } ## End function PrinterCheck  
      
      
    function UpdateHelper  
        {  
        if((Get-Host).Version.Major -cge 5)  
            {  
                $winupdatelog = get-item $tempDir\LOGS\windows-update.log    ##WIN-10 File  
                MD $tempDir\LOGS\Windows\Logs\WindowsUpdate\ -EA SilentlyContinue | Out-Null  
                CP C:\Windows\Logs\WindowsUpdate\*.etl $tempDir\LOGS\Windows\Logs\WindowsUpdate\ -EA SilentlyContinue  
            }  
                Else{$winupdatelog = get-item $tempDir\LOGS\windowsupdate.log} ##LEGACY File  
      
        $updateError = ($winupdatelog | select-string -pattern "error.*0x........");  
        $updateErrorSplit = $updateError -Split " "  
        $updateErrorCount = (($updateErrorSplit | select-string -pattern "0x........") -Replace "[(),'`.:]", "" -Replace "hr=", "");  
      
        $updateErrorCount | Group-Object | Sort-Object Count -Descending | Format-Table Count, Name | Out-File $tempDir\LOGS\UPDATE-ERRORS.TXT -Width 999  
        $updateError >> UPDATE-ERRORS.TXT  
        if($updateError.length -eq 0){"No `"error.*0x........`" patterns Found in Windows-Update.log" | Out-File $tempDir\LOGS\UPDATE-ERRORS.TXT}  
      
        ($winupdatelog | Select-String "KB\d\d\d\d\d\d\d" | Select-string "fail") | Out-file $tempDir\LOGS\UPDATE-ERRORS.TXT -Append -width 999  
      
        } ## End function UpdateHelper  
      
      
    function getProcesses  
        {  
        wh "`nGetting Active Process ...`n"   
        Get-Process > $tempDir\LOGS\Running-Processes.TXT  
        CMD.EXE /C "tasklist /svc" | Out-File -Append  $tempDir\LOGS\Running-Processes.TXT  
          
        } ## End function getProcesses  
      
      
    function GetApps  
        {  
        wh "`n Getting List of Installed Apps...`n"  
        Get-WmiObject -Class Win32_Product | Format-Table -Property Name, Version, Vendor > $tempDir\LOGS\Installed-Apps.TXT  
        Get-AppxPackage | ft Name, Version, InstallLocation, IspArtiallyStaged, SignatureKind, Status >> $tempDir\LOGS\Installed-Apps.TXT  
          
        } ## End function GetApps  
      
      
    function SetupLogs  
        {  
        wh "`nGetting Windows Setup Logs Independent of SetupDiage.exe...`n"  
            MD $tempDir\LOGS\SETUP\ -EA SilentlyContinue  
        dir C:\ > $tempDir\LOGS\Dir_Structure.txt  
          
        ## Main Setup Collection  
        if($env:SystemDrive -eq 'C:') ##Verify SystemDrive  
        {  
            $SetupPaths = @()  
      
            $locations = @(  
                'C:\GetCurrent',  
                'C:\$Reset',  
                'C:\$SysReset',  
                'C:\$Windows.~BT',  
                'C:\$Windows.~WS',  
                'C:\Windows\Logs\',  
                'C:\Windows\Panther\',  
                'C:\Windows\inf\',  
                'C:\Windows\System32\LogFiles\',  
                'C:\Windows\System32\SysPrep\',  
                'C:\Windows10Upgrade',  
                'C:\Windows.old\Windows\Panther')  
      
            for($i = 0; $locations.count -gt $i; $i++)  
            {   
                if((get-item $locations[$i] -Force -EA SilentlyContinue).length -gt 0) ##Null Path Check -Force for Hidden  
                {  
                    CD $locations[$i]  
                    ##Search includes setuperr/setupact only  
                    $SetupPaths += Get-ChildItem * -Force -Recurse -Include setuperr.log, setupact.log, miglog.xml, *APPRAISER_Humanreadable.xml -EA SilentlyContinue      
                }  
            }  
      
            $cleanPaths = @()  
      
            for($i = 0; $SetupPaths.count -gt $i; $i++)  
            {  
                $cleanPaths += $SetupPaths[$i].PSParentPath.ToString() -replace "Microsoft\.PowerShell\.Core\\FileSystem\:\:C\:\\", ""  
            }  
      
            CD $tempDir\LOGS\SETUP\  
            MD $cleanPaths -Force  
            CD $tempDir\LOGS\  
      
            for($i = 0; $SetupPaths.count -gt $i; $i++)  
            {  
                $destPath = "$tempDir\LOGS\SETUP\" + $cleanPaths[$i]  
                $copyPathLog = ($SetupPaths[$i].ToString())  
                  
                Copy  $copyPathLog -Destination $destPath  
            }  
          
        }Else{Write-Host "`nSystem Drive is not C:... Setup Collection Aborted!`n"}  
        ## End Main Setup Collection  
          
              
            ## Setup Reg Output      
            Get-ChildItem HKLM:\SYSTEM\SETUP\ | Out-File $tempDir\LOGS\SETUP\HKLM_SYSTEM_SETUP-OOBE.TXT  
            Get-ChildItem HKLM:\SOFTWARE\Microsoft\Windows\CurrentVersion\OOBE\Me* -recurse -EA SilentlyContinue | Out-File $tempDir\LOGS\SETUP\HKLM_SYSTEM_SETUP-OOBE.TXT -Append  
            Get-Childitem HKLM:SOFTWARE\Microsoft\Windows\CurrentVersion\WindowsUpdate | Out-File $tempDir\LOGS\SETUP\HKLM_SYSTEM_SETUP-OOBE.TXT -Append  
      
            ## SetupAct String Search  
      
      
              
             $setupRegx = @("MOUPG SetupHost..Initialize:",  
                            "============================",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MOUPG  SetupHost..Initialize. CmdLine"),  
                            "",  
                            "MOUPG Setup build & Host OS Build:",  
                            "==================================",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MOUPG  SetupHost..Setup build"),  
                            "...",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MOUPG      Host OS"),  
                            "",  
                            "Watson Parameters (4&5):",  
                            "=======================",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "Watson Bucketing Parameters\[[4-5]\]" ),  
                            "",  
                            "\[0x........\]Error:",  
                            "==================",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "\[0x........\]\[0x.....\]"),  
                            "",  
                            "`"FATAL`":",  
                            "======",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "FATAL" | Select-String -NotMatch "FatalExecutionEngineError" | Select-String -NotMatch "non-fatal"),  
                            "",  
                            "`"Error   `":",  
                            "===========",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "Error   "),  
                            "",  
                            "MIGRATE.*DATA:",  
                            "==============",  
                            "",  
                            (Get-ChildItem $tempDir\LOGS\*setupact.log -Recurse | Select-String "MIGRATE.*DATA"),  
                            ""             
                            )  
                $q=0  
                Do {$setupRegx[$q] | Out-File $tempDir\LOGS\SETUP\SetupAct-Regex.TXT -Append -Width 999 ##spool out results  
                                      $q++                    
                                                }Until($q -eq $setupRegx.Count)  
      
        } ## End function SetupLogs  
      
      
    function powerCFGInfo  
        {  
        MD $tempDir\LOGS\POWER\ -EA SilentlyContinue  | Out-Null  
        wh "`n Grabbing PowerCFG, Sleep & Battery Info ...`n"  
          
        ("`n" + "Available Sleep States (/A): `r" + "`n" +"============================`r" + "`r").ToString() | Out-File -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg /a | Out-File -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "-DeviceQuery Wake_Armed: `r" + "`n" +"========================`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg -devicequery wake_armed  | Out-file -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "Last Wake (-lastwake):  `r" + "`n" +"=====================`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg -lastwake  | Out-file -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        ("`n`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "-Requests: `r" + "`n" +"==========`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        powercfg -requests  | Out-file -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        $powerList = powercfg -list  
        $powerList | Out-File -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        $powerActive = $powerList | select-string "\*" | powercfg /QH "$_"   
        ("`n`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
        ("`n" + "Active Power Scheme Details: `r" + "`n" +"============================`r" + "`r").ToString() | Out-File -Append -Encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
        $powerActive | Out-File -Append -encoding ascii $tempDir\LOGS\POWER\POWERCFG_INFO.txt  
      
      
        if((Get-Host).Version.Major -cge 5) ##WIN7 Does not Support powercfg /battery /sleepstudy  
             {   
               $ifbattery = Get-WmiObject win32_battery  
               if ( $ifbattery.__SERVER.count -cge 1 ) { CMD.EXE /C "powercfg /batteryreport /output %temp%\LOGS\POWER\battery-report.html" }  
               CMD.EXE /C "powercfg /sleepstudy /output %temp%\LOGS\POWER\sleepstudy-report.html"  
             }  
               CMD.EXE /C "powercfg /ENERGY /duration 10 /output %temp%\LOGS\POWER\energy-report.html"         
          
        } ## End function powerCFGInfo  
      
      
    function sysProductCheck  
        {  
        wh "`n Getting SystemProductName ...`n"  
        ##SystemInformation Reg   
        reg query HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\SystemInformation\ /v SystemProductName  > $tempDir\LOGS\REG_SystemProductName.TXT   
        Get-WmiObject Win32_ComputerSystem > $tempDir\LOGS\WMI_Object_System.TXT  
        Get-WmiObject Win32_ComputerSystemProduct >> $tempDir\LOGS\WMI_Object_System.TXT  
          
        } ## End functions sysProductCheck  
      
      
    function showWLAN  
        {  
        wh "Generating NETSH WLAN Report...`n"  
      
        $showWLANjob = {  
                        CMD.EXE /c "netsh wlan show networks mode=ssid > %temp%\LOGS\Network\wlan.txt"  
                        CMD.EXE /c "netsh wlan show networks mode=bssid >> %temp%\LOGS\Network\wlan.txt"  
                        CMD.EXE /c "netsh winhttp show proxy > %temp%\LOGS\Network\proxy.txt"  
                        CMD.EXE /c "netsh wlan show wlanreport & COPY C:\ProgramData\Microsoft\Windows\wlanReport\wlan-report-latest.html %temp%\LOGS\Network\wlan-report-latest.html"   
                        ##WIN7 Does not Support netsh wlanreport                                                    
                        }   
      
        Start-Job -Name showWLAN -ScriptBlock $showWLANjob  
      
        } ## End function sysProductCheck  
      
      
    function getGPRESULT  
        {  
        wh "`nGetting GPRESULT...`n"  
        CMD.EXE /C "GPRESULT /V > %temp%\LOGS\GPRESULT.TXT"  
          
        } ## End function getGPRESULT  
      
      
    function reservedCheck  
        {       
             
        $reservedJob =   
            {  
            $vol = (mountvol /L | select-string -Pattern "\\\\")  
            $volstring = "mountvol y:" + $vol[0]  
            CMD.EXE /C $volstring  
          
            SLEEP 2  
      
            CMD.EXE /C "CHKDSK y: > %temp%\LOGS\SystemReserved.TXT"  
          
            SLEEP 2 # Pause after drive dismount  
          
            CMD.EXE /C "mountvol y: /D"  
            }  
      
        Start-Job -Name reservedJob -ScriptBlock $reservedJob  
          
        } ## End function reservedCheck  
      
      
    function fltmcCheck  
        {  
        wh "`n Getting fltmc Filters ...`n"  
        CMD.EXE /c "fltmc filters > %temp%\LOGS\fltmc_filters.TXT"  
          
        } ## End function fltmcCheck  
      
      
    function getDXDiag  
        {  
        wh "`n Grabbing DXDiag Info...`n"  
        C:\Windows\System32\dxdiag /x $explore\DxDiag  
          
        } ## End function getDXDiag  
      
      
    function getMSINFO  
        {  
        wh "`n Gathering MSINFO32 ...`n"  
        ## check if msinfo is already gathering - if so stop  
        If((get-process | select-string -Pattern "msinfo").Pattern -eq "msinfo")  
        {Stop-Process -ProcessName msinfo32}  
      
            C:\Windows\System32\msinfo32.exe /nfo $tempDir/LOGS/MSINFO32.NFO  
                     
        } ## End function getMSINFO  
      
      
    function getAV  
        {  
         if((Get-Host).Version.Major -cge 5) ##Modern OS Only  
            {  
            wh "`n Grab root\SecurityCenter2 AntivirusProduct ...`n"  
            $avPath = (Get-WmiObject -Namespace root\SecurityCenter2 -Class AntivirusProduct) | % {$_.pathtoSignedProductEXE}  
            "AV Info" + "`n========" | Out-File $tempDir/LOGS/SecurityProductInformation.TXT 
        $avPath | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append  
            if($avPath[0] -match "exe")  
                {   
                    $path = (Get-Item $avPath[0]).PSParentPath  
                    Get-Item $path/*.ini | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append  
                    Get-Content $path/*.ini | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append             
                }  
                Get-ChildItem "HKLM:\SOFTWARE\Policies\Microsoft\Windows Defender\" -recurse -EA SilentlyContinue | Out-File $tempDir/LOGS/SecurityProductInformation.TXT -Append      
            }  
        } ## End function getAV  
      
      
    function getDrivers  
        {  
        wh "`n Grabbing Driver listing via DISM.EXE ...`n"  
            $drivers = cmd.exe /C "dism /online /get-drivers /format:table"  
            $drivers += cmd.exe /C "dism /online /get-drivers /all /format:table"  
            $drivers | Out-File $tempDir/LOGS/DISM-Get-Drivers.TXT  
        wh "`n Done!`n"  
        } ## End Function getDrivers  
      
      
    function getMISCLogs  
        {  
            wh "`nCopying misc. logs ...`n"   
            MD $tempDir\LOGS\WER\ -EA SilentlyContinue   
            MD $tempDir\LOGS\Windows\Logs\WindowsUpdate\ -EA SilentlyContinue  
            CP "C:\Users\All Users\Microsoft\Windows\WER\ReportArchive\*" $tempDir\LOGS\WER\ -Recurse -EA SilentlyContinue  
            CP "C:\Windows\Logs\CBS\*cbs*" $tempDir\LOGS\Windows\Logs\  
            CP "C:\Windows\Logs\DISM\*dism*" $TempDir\LOGS\Windows\Logs\  
            CP "C:\Windows\Logs\WindowsUpdate\*" $TempDir\LOGS\Windows\Logs\WindowsUpdate\  
      
                
            #DMP Collect  
            $dmp = @()  
            $dmp += Get-ChildItem C:\Windows\*.dmp   
            $dmp += (Get-ChildItem C:\Windows\LiveKernelReports\*.dmp -Recurse -EA SilentlyContinue)  
            $dmp += (Get-ChildItem C:\Windows\Minidump\*.dmp -Recurse -EA SilentlyContinue)  
            #Validate empty array  
            if($dmp.length -ne 0)  
                {  
                $dd=0  
                      Do{       
                            If($dmp[$dd].length -lt 2000000)  
                                { $destPath = $dmp[$dd].PSParentPath.Replace('C:\', '').Replace('Microsoft.PowerShell.Core\FileSystem::', '')  
                                    MD $destPath -EA SilentlyContinue 
                                        COPY -Path $dmp[$dd].PSPath -Destination $destPath }  
                            $dd++  
                        }  
                        Until($dd -eq $dmp.Count)  
                }  
     
             #disk info 
             "`nGet-Disk:`n=========" > $tempDir\LOGS\Disk-Info.TXT  
             Get-Disk |fl >> $tempDir\LOGS\Disk-Info.TXT 
             "`nGet-Partition:`n==============" >> $tempDir\LOGS\Disk-Info.TXT  
             Get-Partition >> $tempDir\LOGS\Disk-Info.TXT 
             Manage-bde -protectors -get C: >> $tempDir\LOGS\Disk-Info.TXT 
             "`nIO Fail Search:`n===============`n" >> $tempDir\LOGS\Disk-Info.TXT 
             $search | Select-String ".*io.fail.*" | Select-String -NotMatch '0, 0, 0, 0' >> $tempDir\LOGS\Disk-Info.TXT        
      
        } ## End function getMISCLogs  
      
      
    function bingCollect  
        {  
            ##O365 Firewall Check & Bing.com diagnostics.asp  
            ##URIs based on Article:   
            ##https://support.office.com/en-us/article/Network-requests-in-Office-365-ProPlus-and-Mobile-eb73fcd1-ca88-4d02-a74b-2dd3a9f3364d  
                    
            MD $TempDir\LOGS\Network\ -EA SilentlyContinue  
      
            wh "Performing Bing & O365 URI Check ... `n"  
      
      
                  $bingCheck = (Invoke-WebRequest -Uri https://www.bing.com/fdv2/diagnostics.aspx -UseBasicParsing)   
                  $bingCheck | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT  
                     
                  $URIs = @('api.login.microsoftonline.com',    #0  Standard Reply = 403  
                  'api.passwordreset.microsoftonline.com',      #1  Standard Reply = 200  
                  'becws.microsoftonline.com',                  #2  Standard Reply = 403  
                  'clientconfig.microsoftonline-p.net',         #3  Standard Reply = 404  
                  'companymanager.microsoftonline.com',         #4  Standard Reply = 403  
                  'device.login.microsoftonline.com',           #5  Standard Reply = 200  
                  'graph.microsoft.com',                        #6  Standard Reply = 404  
                  'hip.microsoftonline-p.net',                  #7  Standard Reply = 404   
                  'hipservice.microsoftonline.com',             #8  Standard Reply = 404  
                  'login.microsoft.com',                        #9  Standard Reply = 200  
                  'login.microsoftonline.com',                  #10 Standard Reply = 200  
                  'logincert.microsoftonline.com',              #11 Standard Reply = 200   
                  'loginex.microsoftonline.com',                #12 Standard Reply = 200  
                  'login-us.microsoftonline.com',               #13 Standard Reply = 200  
                  'login.microsoftonline-p.com',                #14 Standard Reply = 200  
                  'login.windows.net',                          #15 Standard Reply = 200  
                  'nexus.microsoftonline-p.com',                #16 Standard Reply = 403  
                  'passwordreset.microsoftonline.com',          #17 Standard Reply = 200  
                  'provisioningapi.microsoftonline.com',        #18 Standard Reply = 403  
                  'stamp2.login.microsoftonline.com',           #19 Standard Reply = 200  
                  'ccs.login.microsoftonline.com',              #20 Standard Reply = 401  
                  'ccs-sdf.login.microsoftonline.com',          #21 Standard Reply = 401  
                  'accounts.accesscontrol.windows.net',         #22 Standard Reply = 200  
                  'secure.aadcdn.microsoftonline-p.com',        #23 Standard Reply = 400  
                  'windows.net',                                #24 Standard Reply = 200  
                  'phonefactor.net',                            #25 Standard Reply = 200  
                  'account.activedirectory.windowsazure.com',   #26 Standard Reply = 404  
                  'secure.aadcdn.microsoftonline-p.com',        #27 Standard Reply = 400  
                  'login.windows.net',                          #28 Standard Reply = 200  
                  'provisioningapi.microsoftonline.com',        #29 Standard Reply = 403  
                  'mscrl.microsoft.com',                        #30 Standard Reply = 400  
                  'secure.aadcdn.microsoftonline-p.com',        #31 Standard Reply = 400  
                  'windowsupdate.microsoft.com',                #32 Standard Reply = 200  
                  'update.microsoft.com',                       #33 Standard Reply = 200  
                  'au.download.windowsupdate.com',              #34 Standard Reply = 200  
                  'download.windowsupdate.com',                 #35 Standard Reply = 200  
                  'download.microsoft.com',                     #36 Standard Reply = 200  
                  'tlu.dl.delivery.mp.microsoft.com');          #37 Standard Reply = 403  
              
                     
                  $count = 0;  
                  $queryResult =@{};  
                     
                  Write-Host "Checking URIs .." -NoNewline  
                     
                  Do {           
                          Try{  
                          $queryResult[$count] = (Invoke-WebRequest -Uri ("http:`/`/" + $URIs[$count]) -Method Head -UseBasicParsing -TimeoutSec 2).RawContent  
                             }Catch{ $catch = $_ }  
                     
                              if($queryResult[$count].Count -eq 0)  
                                      {$queryResult[$count] = ($catch[$catch.count -1].ToString()).Replace("`n", " ")}                                     
                          Write-Host "." -NoNewline           
                          $count++         
                      }Until ($count -eq ($URIs.Count));                            
                  Write-Host "."  
                      
                      Get-Date | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT -Append  
                      $queryResult | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT -Append  
                        
            Write-Host " Bing Check", `n, "==========" | Out-File $tempDir\LOGS\Network\O365-URL-Query.TXT -Append  
            
                  wh "`n`n`n`URL Check Finished...`n"   
        }  
      
      
    function smbConfig  
    {  
      
        $CMDs =  
        {   cmd.exe /c "net config server"    
            cmd.exe /c "net config workstation"  
            Get-SmbClientNetworkInterface  
            Get-SmbServerConfiguration  
            Get-SmbClientConfiguration  
            Get-ChildItem "HKLM:\SYSTEM\CurrentControlSet\Services\LanmanServer"   
            Get-NetAdapterAdvancedProperty | ft }  
      
        ForEach-Object{Invoke-Command $CMDs | Out-File $TempDir\LOGS\NETWORK\$env:COMPUTERNAME-SMB-Config.TXT -Append}  
      
        $share = Get-SmbShare  
      
        ForEach-Object{Get-SmbShareAccess $share.Name | ft  | Out-File $tempDir\LOGS\NETWORK\$env:COMPUTERNAME-SMB-Config.TXT -Append}  
      
    } ## End Function smbConfig  
      
      
    function regLang  
        {       
            DISM.EXE /Online /Get-Intl  | Out-File $tempDir\LOGS\Reg-Lang.TXT  
            "`n","Get-WinUserLanguageList","=======================" | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
            Get-WinUserLanguageList     | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
            "`n","Get-WinLanguageBarOption","========================" | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
            Get-WinLanguageBarOption    | Out-File $tempDir\LOGS\Reg-Lang.TXT -Append  
        }  
      
      
    function autoRotate  
        {  
            Get-ChildItem HKLM:SOFTWARE\Microsoft\Windows\CurrentVersion\Auto* | Out-File $tempDir\LOGS\AutoRotate.TXT  
        }  
      
      
    function checkBoxes  
       {  
            Add-Type -AssemblyName System.Windows.Forms  
            Add-Type -AssemblyName System.Drawing  
      
            $Global:form = New-Object System.Windows.Forms.Form  
            $Global:form.Text = "LOGS-V$ver"  
            $Global:form.Size = New-Object System.Drawing.Size(300,400)  
            $Global:form.StartPosition = 'CenterScreen'  
      
            $OKButton = New-Object System.Windows.Forms.Button  
            $OKButton.Location = New-Object System.Drawing.Point(100,300)  
            $OKButton.Size = New-Object System.Drawing.Size(75,23)  
            $OKButton.Text = 'OK'  
            $OKButton.DialogResult = [System.Windows.Forms.DialogResult]::OK  
            $Global:form.AcceptButton = $OKButton  
            $Global:form.Controls.Add($OKButton)  
             
            $Global:form.ControlBox = $false  
              
                $Global:boxNum = 1  
                $Global:checkBox = @{} #hash for $checkBox  
                $tag = @{} #hash for $label  
                $Global:Box = @{}  
      
                function createCheckBox   
                    {  
                        Param ( [parameter (Mandatory = $true)][string]$name,  
                                [parameter (Mandatory = $true)][string]$label )  
                          
                        $drawingPoint = (50 + ($boxNum *25))  
      
                        $Global:checkBox[$boxNum] = New-Object System.Windows.Forms.CheckBox  
                        $Global:checkBox[$boxNum].Location = New-Object System.Drawing.Point(10,$drawingPoint)  
                        $Global:checkBox[$boxNum].Size = New-Object System.Drawing.Size(15,15)  
                        $Global:checkBox[$boxNum].Text = ''  
                        $Global:checkBox[$boxNum].Checked = $true  
                        $Global:form.Controls.Add($checkBox[$boxNum])  
                        #SetupDiag Label  
                        $tag[$boxNum] = New-Object System.Windows.Forms.Label  
                        $tag[$boxNum].Location = New-Object System.Drawing.Point(40,$drawingPoint)  
                        $tag[$boxNum].Size = New-Object System.Drawing.Size(280,20)  
                        $tag[$boxNum].Text = "$label"  
                        $Global:form.Controls.Add($tag[$boxNum])  
      
                        $Global:boxNum ++  
                      
                    } #End nested function createCheckBox   
                
                createCheckBox -name "EV" -label "EventSearch EventLog Helper"       #1  
                createCheckBox -name "SD" -label "SetupDiag.EXE Setup Diagnostics"   #2  
                createCheckBox -name "WU" -label "Get-WindowsUpdateLog Collection"   #3  
                createCheckBox -name "IP" -label "Network Information"               #4  
                createCheckBox -name "PW" -label "POWERCFG. Sleep & Battery Info"    #5  
                createCheckBox -name "GP" -label "GPResult Info"                     #6  
                createCheckBox -name "MS" -label "General Machine Info"              #7  
                createCheckBox -name "EO" -label "EventSearch Out-GridView"          #8            
                     
                #Checkbox State Changes               
                $Global:checkBox[1].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[1].checked -eq $True){ $Global:EventsCollect = $true ; Write-Host "." -nonewline} Else{ $Global:EventsCollect = $false }  
                                  
                        })             
                $Global:checkBox[2].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[2].checked -eq $True){ $Global:SetupDiagCollect = $true ; Write-Host "." -nonewline} Else{ $Global:SetupDiagCollect = $false }  
                                  
                        })  
                $Global:checkBox[3].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[3].checked -eq $True){ $Global:UpdatesCollect = $true ; Write-Host "." -nonewline} Else{ $Global:UpdatesCollect = $false }  
                                  
                        })  
                $Global:checkBox[4].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[4].checked -eq $True){ $Global:WLANCollect = $true ; Write-Host "." -nonewline} Else{ $Global:WLANCollect = $false }  
                                  
                        })  
      
                $Global:checkBox[5].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[5].checked -eq $True){ $Global:PowerCollect = $true ; Write-Host "." -nonewline} Else{ $Global:PowerCollect = $false }  
                                  
                        })  
                $Global:checkBox[6].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[6].checked -eq $True){ $Global:GPCollect = $true ; Write-Host "." -nonewline} Else{ $Global:GPCollect = $false }  
                                  
                        })  
                $Global:checkBox[7].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[7].checked -eq $True){ $Global:miscCollect = $true ; Write-Host "." -nonewline} Else{ $Global:miscCollect = $false }  
                                  
                        })  
      
                 $Global:checkBox[8].Add_CheckStateChanged(  
                        {   
                            if($Global:checkBox[8].checked -eq $True){ $Global:eventOut = $true ; $Global:checkBox[1].checked = $true; Write-Host "x" -nonewline} Else{ $Global:eventOut = $false }  
                                  
                        })  
                                               
            $Global:checkBox[8].Checked = $false  
            $mainText = New-Object System.Windows.Forms.Label  
            $mainText.Location = New-Object System.Drawing.Point(62,30)  
            $mainText.Size = New-Object System.Drawing.Size(260,20)  
            $mainText.Text = 'Choose which logs to collect:'  
            $Global:form.Controls.Add($mainText)  
            $result = $Global:form.ShowDialog()  
            SLEEP 1  #testing Topmost lag  
            $Global:form.Topmost = $true  
      
            #OK Button ...   
            if ($result -eq [System.Windows.Forms.DialogResult]::OK)  
            {  
                $x = $textBox.Text  
                $x  
            }       
      
        } #End function checkBoxes  
      
      
    Function werHint  
    {  
        $WERs = Get-ChildItem $tempDir\LOGS\WER\*.wer -Recurse  
      
        $WERArray = @()  
      
        $Date = $WERs | Select-String -pattern "eventtime=" | % {$_ -Replace("C:.*EventTime=", "")}  
        $eventType = $WERs | Select-String -pattern "EventType=" | % {$_ -Replace("C:.*EventType=", "")}  
        $Sig0Nam = $WERs | Select-String -pattern "Sig\[0\].Name" | % {$_ -Replace("C:.*Sig\[0\].Name=", "")}  
        $Sig0Val = $WERs | Select-String -pattern "Sig\[0\].Value" | % {$_ -Replace("C:.*Sig\[0\].Value=", "")}  
        $Sig3 = $WERs | Select-String -pattern "Sig\[3\].Value" | % {$_ -Replace("C:.*Sig\[3\].Value=", "")}  
        $Sig3 = $WERs | Select-String -pattern "Sig\[3\].Value" | % {$_ -Replace("C:.*Sig\[3\].Value=", "")}  
        $Sig4 = $WERs | Select-String -pattern "Sig\[4\].Value" | % {$_ -Replace("C:.*Sig\[4\].Value=", "")}  
      
        #ConvertDateTime  
        $epoch = [datetime]"01/01/1601 00:00"  
        $date = $date | foreach{$epoch.AddSeconds($_/10000000)}   
        $convertedDate = foreach($Date in $Date) {Get-Date $Date -Format G}  
      
        $WERarray = 0..($convertedDate.Length -1) | Select-Object @{n="Id";e={$_}},   
            @{n="Date";e={$convertedDate[$_]}}, @{n="EventType";e={$eventType[$_]}},  
                @{n="S0-Name";e={$Sig0Nam[$_]}}, @{n="S0-Value";e={$Sig0Val[$_]}}, @{n="S3";e={$Sig3[$_]}},   
                    @{n="S4";e={$Sig4[$_]}}  
      
        $WERArray |Sort-Object -Descending Date | ft -autosize Date, EventType, S0-Name, S0-Value, S3, S4  |   
            Out-File $tempDir\LOGS\WER-SUMMARY.TXT -Width 500  
      
    } ## End Function werHint  
      
      
      
    ### FUNCTIONS_INIT ###   
      
            $Script:Cancel = @{}  
      
            StartScript #function  
            checkBoxes  
              
            ## SetupDiagCollect   #2  
            if($Global:SetupDiagCollect -eq $True)  
                {  
                SetupDiagFunc #function & job   
                wh "...`n"  
                }  
            ## EventSearch         #1  
            if($Global:EventsCollect -eq $True)  
                {  
                EventSearch #function & job  
                wh "...`n"  
                }  
      
            ## Get-WindowsUpdate   #3  
            if($Global:UpdatesCollect -eq $True)  
                {  
                GetUpdates #function & job  
                wh "...`n`n"  
                }  
      
            ## WLAN/Wifi Collect    #4  
            if($Global:WLANCollect -eq $True)      
                {  
                bingCollect #function  
                wh "...`n"  
                showWLAN #function & job   
                wh "...`n"  
                smbConfig #function  
                }  
      
            ## Power/Battery Collect:#5  
            if($Global:PowerCollect -eq $True)  
                {  
                powerCFGInfo #function - make job takes a min  
                wh "...`n"  
                }  
      
            ## GPRESULT Collection:  #6  
            if($Global:GPCollect -eq $True)  
                {  
                getGPRESULT #function  
                wh "...`n"  
                }  
      
            ## Misc Logs Collection: #7        
            if($Global:miscCollect -eq $True)  
                {  
                getMSINFO #function & job  
                    wh "...`n"  
                PrinterCheck #function  
                    wh "...`n"  
                getProcesses #function  
                    wh "...`n"  
                getApps #function - make job - takes a min  
                    wh "...`n"  
                SetupLogs #function  
                    wh "...`n"       
                sysProductCheck #function  
                    wh "...`n"                 
                reservedCheck #function  
                    wh "...`n"  
                fltmcCheck #function  
                    wh "...`n"  
                getDXDiag #function  
                    wh "...`n"  
                regLang #function  
                    wh "...`n"  
                autoRotate #function  
                getMISCLogs #function  
                    wh "...`n"  
                getDrivers #function  
                    wh "...`n"   
                getAV #function  
                    wh "...`n"            
                 }  
            
      
    #### RECEIVING JOBS SECTION ###...   
      
            #EventSearchJob  
            if($Global:EventsCollect -eq $True)  
            {          
                wh "`nWaiting for EventSearchJob to complete...`n"  
      
                Receive-Job -Name EventSearchJob -OutVariable eventSearch -Wait   
                $search = $eventSearch.Line  
            }  
      
      
            if($Global:SetupDiagCollect -eq $True)  
            {  
                #SetupDiagJob - Receive-Job  
                $stamp = (Get-Date -format "hh:mm tt")  
                wh "`nWaiting for SetupDiagJob to complete..."  
                wh "`nTime Stamp: $stamp"  
                wh "`nThis can take up to 10 minutes ..."  
      
                Do{  
                  SLEEP 15  
                    wh "."  
                    if((Get-Job -name SetupDiagJob).State -eq "Completed")  
                        { Receive-Job -Name SetupDiagJob  
                               wh "`nSetupDiag Completed!"                         
                            Break                      }  
                                    }Until($Cancel.SetupDiag -eq $True)  
                wh `n  
                                                   
                #Receive file and copy  
                Receive-Job -Name SetupDiagJob -Wait   
                Copy-Item $tempDir\Logs*.zip $tempDir\LOGS\SetupDiag-Log.zip  
                Copy-Item $tempDir\setupdiag*.log $tempDir\LOGS\  
                Remove-Item $tempDir\Logs*.zip  
            }  
      
           
            if($Global:UpdatesCollect -eq $True)  
            {  
                #GetUpdates Job via:  
                #UpdateHelper <--- GetUpdates Job has to finish first!  
                #Checking Status of GetUpdates Job...  
                wh "Checking Status of GetUpdates Job...`n"  
                If ((Get-Job -Name GetUpdates).State -eq "Failed")  
                    { wh "`nGetUpdates Job Failed!`n" }  
                        Else{  
                                Receive-Job -Name GetUpdates -wait  
                                Move $env:USERPROFILE\Desktop\WindowsUpdate.log $TempDir\LOGS\Windows-Update.log -Force  
                                wh "`n Writing Update Helper Info to UPDATE-ERRORS.TXT ... `n"  
                                UpdateHelper #run the update helper function  
                            }               
            } #End getting GetUpdates-job       
      
            #Finishing EventSearch  
            if($Global:EventsCollect -eq $True)  
                {  
                    writeSearch #function  
                }  
      
    #Wait on MSINFO...  
    if($Global:miscCollect -eq $True)  
    {  
        wh "`n Waiting for MSINFO32 to Complete ...`n"  
        do{ start-sleep 1 }  
        Until((get-process | select-string -Pattern "msinfo").Pattern -cne "msinfo")  
            werHint #function  
    }  
      
      
    if((Get-Host).Version.Major -cge 5) ##WIN7 Does not Support Transcript  
        {  
      
    Stop-Transcript   
      
            do{  
        start-sleep 1  
        }  
        Until((get-item $tempDir\LOGS\Event-Search.TXT).Length -cne 0)  
          
        }  
      
    wh "`nLog Collection Completed! `nLogs are available in %temp%\LOGS\`n"    
    wh "`nHit Any Key or Close ...`n"  
      
    Start-Sleep 1  
      
    Start Explorer.exe $explore  
      
    PAUSE  
      
    ## LOGS.PS1 1.6.3  ##     
    ## JOHNEM 8-2019 ##   
    ## EOF ##
      My Computer


  4. Posts : 7,086
    Windows 10 Pro 64 bit
       #4

    I hate that message "your device is not ready" when Windows is not ready for your device!
      My Computers


  5. Posts : 34,850
    Win 10 Pro (1903) (2nd PC is 21H2)
       #5

    0xC1900101-0x40017 Installation failed in the Second_Boot phase
    https://docs.microsoft.com/en-us/win...upgrade-errors

    Your Device Is Not Ready
    No known way of finding out how to make it ready, alas. You can review the main points here:
    Known and Resolved issues for Windows 10 May 2020 Update version 2004

    - but could be something else.

    Given it
    is about 10 years old.
    - it's unlikely to magically become ready e.g. by later drivers becoming available. You are running in unspecified territory at your own risk.

    Even if an out of spec. older machine runs one build of Win 10, there's no guarantee whatsoever it won't have problems with the next. If that old PC runs 1909 successfully, I suggest you save time and effort and sleepless nights, and stay with 1909.

    2004 probably doesn't add too much of interest, unless you want PIN sign in to Safe Mode and to chat to Cortana, say...
    What is new in the Windows 10 May 2020 Update version 2004
      My Computers


  6. Posts : 4,556
    Windows 10 Pro
       #6

    I get the same message on my Z170, I think it`s hilarious, I don`t even want 2004 yet, so it`s fine with me. You can always install 2004 with the ISO File if you really wanted to.


    Your Device Is not Ready Vs 2004-capture.jpg
      My Computers


  7. Posts : 3,643
    Windows 11 Pro 64 Bit 21H2
    Thread Starter
       #7

    As stated, my 10 year old desktop gets the message "Your Device is not Ready"
    But both my 10 year old Desktop and the 6 month old Desktop both fail when upgrading thru the same ISO image with the message
    0xC1900101-0x40017 Installation failed in the Second_Boot phase.The only factor that is the same is that each machine shares the same Image I created from the Old computer. The Drivers on the new computer are different.
      My Computer


  8. Posts : 34,850
    Win 10 Pro (1903) (2nd PC is 21H2)
       #8

    Thank you for your reply. Doesn't seem to move on from where you were given comments.

    You may be aware of how unlikely it is that failure to upgrade can be readily resolved. See extensive threads by zbook e.g.
      My Computers


  9. Posts : 3,643
    Windows 11 Pro 64 Bit 21H2
    Thread Starter
       #9

    I have attached the results of the script in Post #3 from the 10 year old computer. Most of it didn't work.
    Your Device Is not Ready Vs 2004 Attached Files
      My Computer


  10. Posts : 39,953
    windows 10 professional version 1607 build 14393.969 64 bit
       #10

    1) Please upload each V2 and DM directly into this thread:
    BSOD - Posting Instructions

    2) Run setupdiag > post a share link for all files into the thread:
    https://docs.microsoft.com/en-us/win...rade/setupdiag

    3) Download and install: Everything
    voidtools

    4) Launch the application and search for these folders / files:

    C:\Windows\Panther

    Code:
    folders:
    \$Windows.~bt\sources\panther
    \$Windows.~bt\Sources\Rollback
    \Windows\Panther
    \Windows\Panther\NewOS
    
    setuperr.log
    setupact.log
    Setupmem.dmp
    setupapi.dev.log
    BlueBox.log
    Event logs (*.evtx)
    C:\$Windows.~BT\Sources\Rollback
    $Windows.~bt\Sources\Rollback\setupmem.dmp
    $Windows.~bt\Sources\Rollback\setupapi\setupapi.dev.log
    $Windows.~bt\Sources\Rollback*.evtx
    $Windows.~BT\Sources\Panther\UnattendGC
    miglog.xml
    Windows\Logs\Mosetup
    Setupapi.offline.log
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 05:12.
Find Us




Windows 10 Forums