Page 1 of 4 123 ... LastLast
  1.    13 Oct 2014 #1

    Acronis True Image to restore after W10 install??


    I installed the Preview on a couple machines with 10" screens and while I liked the overall look and feel, I didn't care for it on those smaller screens. So I took them back to originals which was a totally no fun process. Probably because I did the restore using the MS and mfg tools with a USB stick.

    Now I'm thinking that it would be wonderful on my HP 23" touch AIO. I've imaged with Acronis True Image WD edition to the WD MyBook and made a bootable USB stick. I tested that as far as booting and finding the image I created but haven't actually re-imaged the internal drive.

    So does the Acronis image re-do all the partitions? IOW, will re-imaging the internal drive restore all the partitions back to what they were at the time I created the image?

    Thanks.
      My System SpecsSystem Spec


  2. Joined : Jan 2014
    Walnut Beach, Milford, Ct
    Posts : 7,627
    Win10 Pro / Remix 3.0
       13 Oct 2014 #2

    The safest waay to use Win 10 is a VMware virtual machine. Second best would be a dual boot with your other OS.

    When I opened settings in Acronis 2014, there were only three of the six partitions checked under "Disk Backup "

    I made sure all six were checked so it they would all be included in the backup.

    I did the same as you did in trying to see if it would work, but never fully tested it.
    Attached Thumbnails Attached Thumbnails Acronis2.PNG  
      My System SpecsSystem Spec

  3.    13 Oct 2014 #3

    Thanks for the feedback.

    I currently have the preview installed in a VM, but it is the 32-bit version as the 64-bit won't install for whatever reason. I'm using VMWare Player.

    It is interesting and frustrating to see how convoluted MS has made the partitioning scheme and how that all applies to a system rebuild or in the case of a new drive.

    I've been a Mac guy for a long time, and there it is just a simple clone of the drive and you're good to go. Apple doesn't allow for changing the 'recovery' partition from the factory load.

    Frankly I wish MS didn't futz with it with the Preview either! It would make it so much simpler to go back with the tools in W8.x and W10 as they are.
      My System SpecsSystem Spec

  4.    13 Oct 2014 #4

    Hi there

    Acronis 2014 works perfectly --I always use the BOOTABLE version though. It will also work whether UEFI or NON UEFI system.

    Note though - be careful if you are recovering Storage Spaces -- you need to recover ALL the volumes in the pool.

    On recovery choose the whole disk -- remember though to set the CORRECT partition to ACTIVE otherwise after restore you won't be able to BOOT. If you make a mistake GPARTED or similar stand alone partition manager can set this without you having to restore the whole thing again.

    Cheers
    jimbo
      My System SpecsSystem Spec

  5.    13 Oct 2014 #5

    Thanks.

    'storage spaces'??

    And which is the correct partition?

    Sorry for what may be dumb questions, but I've been away from Windows for a very long time.
      My System SpecsSystem Spec


  6. Joined : Apr 2014
    Space coast of Florida
    Posts : 4,351
    Windows 10 Pro X64 14393.576
       14 Oct 2014 #6
      My System SpecsSystem Spec

  7.    14 Oct 2014 #7

    Ztruker said: View Post
    I did and it doesn't apply to me. Thanks.
      My System SpecsSystem Spec

  8.    15 Oct 2014 #8

    After the failed W10 install on my HP AIO, I used Acronis to do the restore.

    Couldn't have been easier and with Acronis True Image 2014, you don't have to disable secure boot to start the process.
      My System SpecsSystem Spec


  9. Joined : Jan 2014
    Walnut Beach, Milford, Ct
    Posts : 7,627
    Win10 Pro / Remix 3.0
       15 Oct 2014 #9

    Would you give some more detail on what it restored ?
    Did it replace all the partitions as they were before ? Did you have to add any partitions as I did in post #2 ?

    Why did Win 10 fail to install, what was the problem ?
      My System SpecsSystem Spec

  10.    15 Oct 2014 #10

    COMPUTIAC said: View Post
    Would you give some more detail on what it restored ?
    Did it replace all the partitions as they were before ? Did you have to add any partitions as I did in post #2 ?

    Why did Win 10 fail to install, what was the problem ?
    OK, have to work from memory which isn't the best as I get older though...

    during the restore process I had to manually pick which partitions to restore which was a bit slow doing, but not daunting once I figured out the screen was literally telling me which to recognize or whatever the term was it used. That was for every partition. My assumption is that you wouldn't have to restore a partition that didn't get damaged or whatever. Of course, in the case of W10, you need them all as W10 changes the recovery also.

    I picked all of them and matched to the corresponding location on the internal drive. No additional drives were shown, nor did I have to designate one to actually boot from. Once that was done, a simple click and off it went and about 1/2 later it was done.

    The failure to install on my HP 23-N010 AIO desktop was at the last reboot during the install. Up until then, all had proceeded normally. But on the final boot I got a full flashing blue screen and it wouldn't go further than that. I have not figured out what it didn't like. But I'm beginning to think that since I had Malwarebytes Premium running, that may have caused something to not get written to the HD during the update process. Just a total guess.

    At this point I still have my 32-bit W10 available in a VM on the machine, so I could just use that. Or I could try another install only this time choosing a virgin install instead of an upgrade. Or I guess I could go for dual-boot. I haven't figured out yet which I will do.
      My System SpecsSystem Spec


 
Page 1 of 4 123 ... LastLast


Similar Threads
Thread Forum
Solved Activate Windows 10240 via Image restore (Acronis etc)
Hi there You CAN activate Windows 10240 on to a new system if you've copied / restored from an already activated image even if it's on different hardware. After re-boot smply update some of the drivers --Video / graphics is usually the most...
Windows Updates and Activation
W10 Disk Image Utility Reports Error After Image Creation.
I installed the 32 bit version of W10 on an old Acer laptop to get back up to speed with developments, and one of the first questions or issues that cropped up is when using W10's disk image utility to make a system image. I deliberately wished to...
General Support
Solved May help W10 user; Win7Pro "Dirty Install" via double image restore...
The following just might be useful to a Windows 8+, Windows 10+ user having similar crashNburn & recovery. My original post in a few Windows 7 forums: Windows 7 Pro "Dirty Install" instructions needed. Is there a link here or elsewhere for...
General Support
Starting Acronis UEFI Loader
Following a recent update to my build, the start screen became interrupted by the message above. The full message is: Starting Acronis UEFI Loader ... Select an item by using the keyboard: 1. Acronis True Image 2015 2. Acronis System Report...
Software and Apps
Solved In defence of Acronis ATH 2015
Hi there I've long complained that the Interface on Acronis is just getting crazier and crazier. They reached the peak level of complexity with ATH 2014. I'm please to see that with ATH 2015 the interface has been totally re-written and has gone...
Software and Apps
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 14:40.
Find Us
Twitter Facebook Google+



Windows 10 Forums