1. Joined : Jul 2015
    SouthWest, FLorida
    Posts : 469
    Win 10 Pro (x64), OSX 10.11
       24 Aug 2015 #1

    Install error 0x8007045d -0x2000c


    Neighbor had his HP 15 laptop fixed and returned with a new re-imaged 8.1.
    The problem was with a cracked LCD screen and was under warranty. This
    is a AMD A8 with 4 GB memory and 750 GB hard drive.

    He decided to upgrade to Windows 10. He run the Windows Update under Window 8.1 to pick up the latest fixes then start the Windows 10 upgrade using USB drive with the Windows 10 Upgrade Image. During the Windows 10 installation on or around 14% over all progress while copying files, he went to slept and let the upgrade continue. The first thing he noticed in the morning was,

    "We couldn't install Windows 10 we've set your PC back to the way it was right before you start installing Windows 10
    0x8007045D- 0x2000C
    The installation failed in the SAFE_OS phase with an error during APPLY_iMAGE operation."

    So he is back to Windows 8.1. We just run a CheckDisk and a quick memory test. Of course, no problem detected.

    I just observed that it is at the over all progress of 15% and copying files 52%.

    From my past experience, 0x8007045D is normally an I/O operation failure.

    Will post more info as we going through this!
    Last edited by snoopy51; 25 Aug 2015 at 08:23.
      My System SpecsSystem Spec


  2. Joined : Jul 2015
    SouthWest, FLorida
    Posts : 469
    Win 10 Pro (x64), OSX 10.11
       24 Aug 2015 #2

    Well, it went through about 32% in installation but a quick message about installation failure and recovered back to Windows 8.1.

    Need to go to work now. We will debug this and post more info later after work!
      My System SpecsSystem Spec


  3. Joined : Jul 2015
    SouthWest, FLorida
    Posts : 469
    Win 10 Pro (x64), OSX 10.11
       25 Aug 2015 #3

    Well, I run a chkdsk and restart the Windows 10 Upgrade again. This time went further at 40%+ but BSOD and eventually display an error 0xc1900101-0x30018. Oh, well, this was documented in the Forum here. So, will try to disable, Firewall, WiFi, etc.

    Windows 10 Error code 0xc1900101-0x30018

    The message from Windows 10 Upgrade:

    "We couldn't install Windows 10
    0xC1900101 - 0x20018
    The installation failed in the SAFE_OS phase with an error during boot operations"
    Last edited by snoopy51; 25 Aug 2015 at 09:12.
      My System SpecsSystem Spec


  4. Joined : Jul 2015
    SouthWest, FLorida
    Posts : 469
    Win 10 Pro (x64), OSX 10.11
       25 Aug 2015 #4

    Ran CHKDSK again but on reboot, it stuck at "Scanning and Repairing Drive C: 10% complete!" message for over 60 minutes.

    Possible hard drive problem?
      My System SpecsSystem Spec


  5. Joined : Jul 2015
    SouthWest, FLorida
    Posts : 469
    Win 10 Pro (x64), OSX 10.11
       25 Aug 2015 #5

    Back in Windows 8.1 now. Use the chkdsk c: /f/r in the command prompt (admin) to schedule a Check Disk on reboot.
    On reboot, stuck on "Scanning and Repairing Drive C:".

    Power off after almost 2 hours, try to restart in Safe Mode with Networking, but again it start the Checkdisk and it is at 10% again for the last 10 minutes.

    Any help is appreciate!
      My System SpecsSystem Spec


  6. Joined : Jul 2015
    SouthWest, FLorida
    Posts : 469
    Win 10 Pro (x64), OSX 10.11
       15 Sep 2015 #6

    Just an update we forgot to post!
    We run hard disk utility from the vendor, it failed DST test with an error code.
    We simply replaced the hard drive.
    Windows 10 install worked!
      My System SpecsSystem Spec


 


Similar Threads
Thread Forum
We Couldn't install windows 10 0x80070070 - 0x2000C
Everything started installing fine, it then rebooted and loaded the windows 10 logo with a huge "Windows is upgrading" on my screen, at around 10% it reboots, says somethign weird about "restoring to previous windows version", loads my current...
Installation and Setup
Error- You need to install at least 2gb of RAM...
My pc has 8 gb of ram. I have gone into the BIOS and turned on default settings to see if that fixes it (it doesn't). Attempting to install off of a flash drive. Trying to boot off of a flash drive instructs me to install while in windows if...
Installation and Setup
On install getting IRQL error
During the upgrade I get IRQL_Not_equal_or_less error then it restarts and puts my windows 7 back to how it was. Causing me to need to download windows 10 again.
Installation and Setup
Install error
Hello forum i try to install w10 from insider preview 10158 i always got this error after 10x try error is 0x8007002c-0x4000d thanks for help rgds guy
Installation and Setup
Solved Can't Install error 0x80070017
I have created a USB install drive with Windows USB/DVD Tool and successfully created a Virtual Machine with Virtual Box. The virtual machine works fine so now I want to run dual boot with Win 7 64bit. Using the same USB drive the installation...
Installation and Setup
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 08:23.
Find Us
Twitter Facebook Google+



Windows 10 Forums