windows 10 no advanced-startup-options, so no startup settings

Using post #4 please follow up so that we have that information to work with.

What problems are you experiencing with the computer that you are attempting to repair?
Do you know the status of the drive?

Find a flash drive that you can format.
Make a bootable Windows 10 iso:
Download Windows 10



Please update the "My Computer" section with the computer specifications:

How To Fill Out Your System Specs
How To Fill Out Your System Specs
System Specs - Fill in at Ten Forums:
System Specs - Fill in at Ten Forums Windows 10 General Tips Tutorials
In the left corner below in your post you find 'My System Specs'.
After clicking it you can find a link a little below that says 'Update your System Spec', click on this link to get to the page where you can fill in your system specs.
System Info - See Your System Specs - Windows 7 Help Forums

when i did 1. 2. 3. steps i checked and problem was SOLVED
but after 4. 5. 6. 7. steps i checked and no advanced startup options again

1. Make a complete backup image of your current HD including all partitions to an external HD using macrium reflect . Once done, disconnect all USB devices from the PC. Assuming now you only have one HD connected to the PC which you will be installing Windows.
   IMPORTANT: Also create a Macrium Rescue disk to boot from later on.
2. Boot up your Windows installation USB/DVD. On the first screen, Hold SHIFT + F10 to open Command Windows then type:
   Diskpart
   select disk 0
   clean
   exit
3. Click Next, Choose Custom, select the unallocated partition then click Next (Do not format), when asked for Product ID key, click on "Skip this step"/"Do it later". Continue the Installation.
4. Once done. With the external HD connected, Reboot your PC with the Macrium Rescue disk, select the image that you created in step 1 as the Source.
5. Select your current HD/SSD as Destination disk
6. Restore only C: Drive to it. ie. overwrite the new C: Drive with your backup C: Drive.
   NOTE: See screen shot on how to perform this step
7. Disconnect all the external devices. Reboot. Windows should perform a startup repair.

till 4. step there was no windows 10 key activeted and problem vas solved
but after step 7 i checked key and it was not the same which i purchased, why did that change? i activated purchased key again.
so is the problem to be a windows 10 key on my pc?
or do some drivers prevent advancedstartup options?

The information in the "My Computer" will enable all those viewing the thread to find the computer information and provide support.
1) Please update this section:

2) Can you tell us what has happened on your computer that you need to use the windows advanced troubleshooting menu?
Were there recent hardware or software changes?
Was there malware?

3) What is the status of the drive?
Were there any SMART, short, or long generic tests?

4) What is the history of Windows installations and upgrades?
Was it a windows 7 to 8.1 to 10 upgrade?
What is the current operating system version and build?


How To Fill Out Your System Specs
How To Fill Out Your System Specs
System Specs - Fill in at Ten Forums:
System Specs - Fill in at Ten Forums Windows 10 General Tips Tutorials
In the left corner below in your post you find 'My System Specs'.
After clicking it you can find a link a little below that says 'Update your System Spec', click on this link to get to the page where you can fill in your system specs.
System Info - See Your System Specs - Windows 7 Help Forums

zbook said:

Using post #4 please follow up so that we have that information to work with.

What problems are you experiencing with the computer that you are attempting to repair?
Do you know the status of the drive?

Find a flash drive that you can format.
Make a bootable Windows 10 iso:
Download Windows 10



Please update the "My Computer" section with the computer specifications:

How To Fill Out Your System Specs
How To Fill Out Your System Specs
System Specs - Fill in at Ten Forums:
System Specs - Fill in at Ten Forums Windows 10 General Tips Tutorials
In the left corner below in your post you find 'My System Specs'.
After clicking it you can find a link a little below that says 'Update your System Spec', click on this link to get to the page where you can fill in your system specs.
System Info - See Your System Specs - Windows 7 Help Forums

updated....

i need disable driver signature enforcement sometimes.
when i see only turnoff option i dont like that ,
even i dont need repair anything perhaps one day i will need other options

In post 12 it is unclear which steps that you are following.
If you are using another website please post links into the thread so we can follow the steps.

1) Can you tell us what has happened on your computer that you need to use the windows advanced troubleshooting menu?
Were there recent hardware or software changes?
Was there malware?

2) What is the status of the drive?
Were there any SMART, short, or long generic tests?

3) What is the history of Windows installations and upgrades?
Was it a windows 7 to 8.1 to 10 upgrade?
What is the current operating system version and build?

The Advanced Troubleshooting Menu runs from the Windows Recovery Environment (WinRE). The Windows Recovery Environment is normally contained in a 450MB recovery partition. The problem is that there either was not a proper recovery environment present, or that Windows 10 was not linked to it. The link to the WinRE is set with the reagentc command. reagentc /info will tell you the status of WinRE. reagentc /setreimage will create the link to the Recovery Environment, if there is a proper WinRE to link to in the Recovery Partition.

Doing the clean install on the hard drive should have created the proper Recovery Partition with the proper WinRE contained in it. However, the previous Windows install did not contain a reagentc link to it, so it still would not work after the old Windows was restored over the top of the clean install.

The next step is to get a screenshot of disk management, and a list of the partitions on the hard drive, either with a program like MiniTool Partition Wizard - or using diskpart commands to determine the actual partition number of the recovery partition so that it can be linked to with the reagentc /setreimage command.

The command should be:
reagentc /setreimage /path \\?GLOBALROOT\device\harddisk0\partition#\Recovery\WindowsRE

But you need to know the real partition # and you can't trust built-in Windows disk management because it will not show the hidden Microsoft Reserved Partition on GPT partitioned drives when booting in UEFI mode.

zbook said:

In post 12 it is unclear which steps that you are following.
If you are using another website please post links into the thread so we can follow the steps.

1) Can you tell us what has happened on your computer that you need to use the windows advanced troubleshooting menu?
Were there recent hardware or software changes?
Was there malware?

2) What is the status of the drive?
Were there any SMART, short, or long generic tests?

3) What is the history of Windows installations and upgrades?
Was it a windows 7 to 8.1 to 10 upgrade?
What is the current operating system version and build?

1.i need disable driver signature enforcement sometimes.
when i see only turnoff option i dont like that ,
even i dont need repair anything perhaps one day i will need other options as i wrote before

2. ? all pc parts brand was new

3. first windows 7, later upgraded to windows 10 over it, later clean installs of w10 several times because to reach advanced options but couldnt.

NavyLCDR said:

The Advanced Troubleshooting Menu runs from the Windows Recovery Environment (WinRE). The Windows Recovery Environment is normally contained in a 450MB recovery partition. The problem is that there either was not a proper recovery environment present, or that Windows 10 was not linked to it. The link to the WinRE is set with the reagentc command. reagentc /info will tell you the status of WinRE. reagentc /setreimage will create the link to the Recovery Environment, if there is a proper WinRE to link to in the Recovery Partition.

Doing the clean install on the hard drive should have created the proper Recovery Partition with the proper WinRE contained in it. However, the previous Windows install did not contain a reagentc link to it, so it still would not work after the old Windows was restored over the top of the clean install.

The next step is to get a screenshot of disk management, and a list of the partitions on the hard drive, either with a program like MiniTool Partition Wizard - or using diskpart commands to determine the actual partition number of the recovery partition so that it can be linked to with the reagentc /setreimage command.

The command should be:
reagentc /setreimage /path \\?GLOBALROOT\device\harddisk0\partition#\Recovery\WindowsRE

But you need to know the real partition # and you can't trust built-in Windows disk management because it will not show the hidden Microsoft Reserved Partition on GPT partitioned drives when booting in UEFI mode.

i did clean install several times but problem not solved thats why i dont want to do it again

Your current Windows 10 installation itself is broken. If it was just not linked to a recovery partition you would see this:

Code:

Microsoft Windows [Version 10.0.15063]
(c) 2017 Microsoft Corporation. All rights reserved.

C:\Windows\system32>reagentc /info
Windows Recovery Environment (Windows RE) and system reset configuration
Information:

    Windows RE status:         Disabled
    Windows RE location:
    Boot Configuration Data (BCD) identifier: 5c538c41-3716-11e7-b334-d8cb8a71f683
    Recovery image location:
    Recovery image index:      0
    Custom image location:
    Custom image index:        0

REAGENTC.EXE: Operation Successful.

You can try to repair your current Windows installation and see if you can at least get the above result:
Repair Install Windows 10 with an In-place Upgrade Windows 10 Installation Upgrade Tutorials

If that doesn't work, then you are just going to have to settle with starting over with a clean install and not copying your broken Windows 10 over it.