Windows Repair Loop


  1. Posts : 3
    Microsoft
       #1

    Windows Repair Loop


    My computer keeps showing the same thing after I received quite a few blue screens all of a sudden. This hasnt happened before.
    I've tried
    Startup Settings, Startup Repair and Command prompt but none works, saying that theres some sort of 'problem'.
    The only thing I've been able to do was System Restore, but when I choose a restore point it says "You must enable system protection in this drive".
    Is there any way I can change this?
      My Computer


  2. Posts : 39,994
    windows 10 professional version 1607 build 14393.969 64 bit
       #2
      My Computer


  3. Posts : 1,467
    Windows 10 Pro
       #3

    Be prepared for worst case scenario (several options for this)

    Do you need to recover personal data?
      My Computer


  4. Posts : 3
    Microsoft
    Thread Starter
       #4

    Thank you for the assistance, but one I started my PC again it not says

    Your PC/Device needs to be repaired
    An unexpected error has occurred.
    Error code: 0Śc0000034

    You'll need to use recovery tools. If you don't have any installation media, contant you PC administrator or PC/Device manufacturer.

    Is my PC a lost cause?

    - - - Updated - - -

    It would be most ideal to, but it's nothing extremely important.
      My Computer


  5. Posts : 4,546
    Windows 11 Pro 64-bit
       #5

    Please boot your computer with Windows Setup Media and from Windows Recovery Environment start the Command Prompt.

    Please type below command into Command Prompt and press Enter key.

    Following command will fixes errors on the disk and locates bad sectors and recovers readable information.


    Code:
    Chkdsk D: /r


    Please replace partition letter D: with Windows installed partition letter. When computer boots into Windows Recovery Environment (WinRE) environment the drive letter assign to Windows partition may not be C: drive letter because Windows 7, 8 , 8.1 and 10 creates a separate system partition when it's installed from scratch. The system partition contains boot files WinRE assigns the system partition the C: drive letter and the Windows installed partition will be assign any other drive letter usually D: drive letter is assign to Windows installed partition. The Bcdedit /enum | find "osdevice" command can be use to find out the drive letter of the Windows installed partition the output of the Bcdedit command is similar to this osdevice partition=D:. The drive letter after partition= is the drive letter of the Windows partition.




    Please boot your computer with Windows Setup Media and from Windows Recovery Environment start the Command Prompt.

    Please type below command into Command Prompt and press Enter key.

    The following command scans integrity of all protected Windows system files and repairs files with problems when possible.

    Code:
    Sfc  /Scannow   /OFFBOOTDIR=D:\   /OFFWINDIR=D:\Windows


    Please replace partition letter D: with Windows installed partition letter. When computer boots into Windows Recovery Environment (WinRE) environment the drive letter assign to Windows partition may not be C: drive letter because Windows 7, 8 , 8.1 and 10 creates a separate system partition when it's installed from scratch. The system partition contains boot files WinRE assigns the system partition the C: drive letter and the Windows installed partition will be assign any other drive letter usually D: drive letter is assign to Windows installed partition. The Bcdedit /enum | find "osdevice" command can be use to find out the drive letter of the Windows installed partition the output of the Bcdedit command is similar to this osdevice partition=D:. The drive letter after partition= is the drive letter of the Windows partition.



    Please boot your computer with Windows Setup Media and from Windows Recovery Environment start the Command Prompt.

    Please type below commands into Command Prompt and press Enter key.

    Following commands will repair Master Boot Record (MBR), Boot Sector and BCD Store.


    Code:
    Bootrec /FixMbr
    
    Bootrec  /FixBoot
    
    Bootrec /scanos
    
    Bootrec  /RebuildBcd
      My Computer


  6. Posts : 3
    Microsoft
    Thread Starter
       #6

    Thank you so much, it worked!
      My Computer


  7. Posts : 4,546
    Windows 11 Pro 64-bit
       #7

    midblu said:
    Thank you so much, it worked!
    Can you please let us know which commands repaired boot failure.
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 02:40.
Find Us




Windows 10 Forums