Seagate Barracuda 3GB no longer being properly recognised, and beeping

Page 1 of 2 12 LastLast

  1. Posts : 6
    Windows 10 Home
       #1

    Seagate Barracuda 3GB no longer being properly recognised, and beeping


    I have a Seagate External HDD, srd00f2, that until yesterday was working perfectly. I can not think of anything that has changed, other than that the drive is no longer being recognised by Windows, and is beeping when connected. I have already tried a number of things, and have the following results:

    Connecting 'normally' through USB. My laptop's USBs have been playing up a little recently, but I have tried the drive with two separate cables, on two separate laptops.

    Windows Disk Management shows:
    Unknown
    3.86 GB
    Not Initialised
    and to the right, one partition of 3.86GB, Unallocated.

    Hard Disk Sentinal shows the serial number and 3.9GB, but no other information and a lot of '?'s

    Minitool Partition Wizard shows
    Disk 2
    MBR
    3.86 GB
    Read Only (in red)

    and then next to it, 3.9 GB, Bad Disk

    HD Tune Pro allows me to do an error scan, but gives 100% bad sectors. If I do any other tests, I get I/O error, test aborted.

    Safely Remove Hardware shows Eject Expansion Disk

    DISKPART shows the drive as online, 3950MB total size, 3950MB free. I tried attr disk clear readonly but got the error that Diskpart failed to clear the attribute.


    Connecting as a SATA drive.

    I removed the drive from its case. Inside is a Barracuda 3TB drive, model st3000dm001. I have connected it using a SATA to USB 2.0 adaptor, and the results are even worse.

    In Windows Disk Management, it shows Disk 1 as Unknown, Not Initialised. Trying to initialise the disk as GPT gives the error that the disk is too small, and the device indicates as 'Not Ready' if done as MBR.

    HD Tune Pro reacts exactly the same as when connected by USB

    Minitool Partition Wizard
    shows the disk as:
    Disk 2
    MBR
    0.00 GB
    and there is no way of interacting with the disk.

    Hard Disk Sentinal is, again, just showing ???

    The option in Safely Remove Hardware is: Eject USB to ATA/ATAPI Bridge

    The disk beeps as it is connected. as I plug it in, the disk spins up and then gives me:
    1 beep
    0.5 second pause
    1 beep
    1.0 second pause
    1 beep

    I have tried everything I can think of, and everything Google can think of on my behalf. The data on the drive is, naturally, quite important so I'm looking to save the data rather than the drive.

    Thanks in advance for your help and suggestions!

    Jenks

    And as a picture paints a thousand words - this is connected through USB
    Seagate Barracuda 3GB no longer being properly recognised, and beeping-disk-issues.jpg
      My Computer

  2. Caledon Ken's Avatar
    Posts : 24,413
    Windows 10 Pro x64 Version 2004
       #2

    Hi Jenks. Welcome to the TenForums @jenkachu.

    While I'm not the expert in this recover area I wanted you to see the posting when I saw your message that it appeared worse when removed from drive. @jumanji states it has to do with formatting so please have a read before going further. He also mentions another tool.

    Hard Drive seems corrupt. 1 Partition now showing as 3 Partitions?


    Ken
      My Computer

  3. jumanji's Avatar
    Posts : 5,839
    Windows 10 Home 64bit Version 20H2
       #3

    Hi jenkachu,

    1. Your Seagate 3TB external drive is an MBR drive. Inside its original enclosure Partition Wizard showed it as Read Only. This will signify that there has been a catastrophic failure of the HDD proper inside the enclosure.

    2. The electronics inside the original enclosure has a special Drive Translation circuit that enables the 3TB HDD to be formatted as an MBR drive with full 3TB capacity. ( Without that special Drive Translation circuitry, you can only format 2TB of the 3TB as an MBR drive). For that reason putting the HDD on a third party enclosure or trying it with a SATA to USB adapter ( without the Drive Translation circuitry) is not going to help in diagnosing the fault. or recovering the data.

    3. In the case which Caledon Ken has referred in the previous post, the enclosure electronics with the Drive Translation circuit had failed. The HDD itself was OK. Not so in your case with a beeping external HDD. I think it still beeps when connected through the adapter.

    4. The solution: Read Beeping Hard Drive | My Computer Is Beeping | Beeping Noises
    Last edited by jumanji; 16 Mar 2017 at 02:16.
      My Computer


  4. Posts : 6
    Windows 10 Home
    Thread Starter
       #4

    Thank you, both, for your time. It appears the drive must go to the data-storage rubbish dump in the sky...
      My Computer

  5. Caledon Ken's Avatar
    Posts : 24,413
    Windows 10 Pro x64 Version 2004
       #5

    As you are going to destroy drive anyway you might what to "bump" it to see if it might become "Unstuck".


    Ken
      My Computer

  6. jumanji's Avatar
    Posts : 5,839
    Windows 10 Home 64bit Version 20H2
       #6

    Failing which you may even get more adventurous :).

      My Computer

  7. SoFine409's Avatar
    Posts : 1,294
    Win10 Pro
       #7

    jumanji said:
    Failing which you may even get more adventurous :).

    very informative. Thanks for posting.
      My Computers


  8. Posts : 6
    Windows 10 Home
    Thread Starter
       #8

    So, I tried a little percussion engineering, with no discernible change. I then opened the drive up, but the heads were already parked (pic to follow). I put it back to gether, nd turned it on. It didn't explode, but it also didn't work. Here's a video of the beeps as I power it up, as it doesn't sound the same as the other videos with stuck heads...

      My Computer


  9. Posts : 6
    Windows 10 Home
    Thread Starter
       #9

    Seagate Barracuda 3GB no longer being properly recognised, and beeping-img_2394.jpg
    The insides!
      My Computer

  10. Caledon Ken's Avatar
    Posts : 24,413
    Windows 10 Pro x64 Version 2004
       #10

    I wonder if running the seatools against it would do anything. You hear it spinning up.

    Identifying and troubleshooting hard drive noise issues
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 06:43.
Find Us




Windows 10 Forums