Windows 10: Samsung SSD 850 EVO Solved

Page 5 of 32 FirstFirst ... 3456715 ... LastLast
  1. jds63's Avatar
    Posts : 3,106
    Windows 10 Pro 64 bit
       21 Oct 2015 #41

    Gary said: View Post
    I tried it won't boot and it is using Trim.
    Strange, might be another setting unless BIOS needs updating, not sure always risky, usually not these days to.You have SATA controller drivers installed as shown from your motherboard site ?
      My ComputerSystem Spec

  2. jds63's Avatar
    Posts : 3,106
    Windows 10 Pro 64 bit
       21 Oct 2015 #42

    See here, need drivers in place before can switch modes similar topic http://www.tomshardware.com/answers/...ahci-mode.html
      My ComputerSystem Spec


  3. Posts : 91
    64-bit 10240 10 Pro
    Thread Starter
       21 Oct 2015 #43

    jds63 said: View Post
    Strange, might be another setting unless BIOS needs updating, not sure always risky, usually not these days to.You have SATA controller drivers installed as shown from your motherboard site ?
    No I only have Sata II. I set it in the Bios but it would not boot. Macrium Reported that Trim was installed. MSI has no more updates for my MOBO.

    Click image for larger version. 

Name:	dd.PNG 
Views:	6 
Size:	39.3 KB 
ID:	43989
      My ComputerSystem Spec

  4. jds63's Avatar
    Posts : 3,106
    Windows 10 Pro 64 bit
       21 Oct 2015 #44

    Gary said: View Post
    No I only have Sata II. I set it in the Bios but it would not boot. Macrium Reported that Trim was installed. MSI has no more updates for my MOBO.

    Click image for larger version. 

Name:	dd.PNG 
Views:	6 
Size:	39.3 KB 
ID:	43989
    Yes, i posted the motherboard site in past posts, had SATA AHCI drivers although for Windows 7 32bit and 64bit, still may work as i see not installed in Device manager in pic. Be possible why they list them, your unable to use AHCI Mode even though SATA II.
      My ComputerSystem Spec


  5. Posts : 91
    64-bit 10240 10 Pro
    Thread Starter
       21 Oct 2015 #45

    I have an MSI X58-Pro-E Model MS-7522 and the site I used to go to is either changed as I get a 404.
      My ComputerSystem Spec


  6. Posts : 91
    64-bit 10240 10 Pro
    Thread Starter
       21 Oct 2015 #46

    I used google to Find their update program and this is what it reported

    Click image for larger version. 

Name:	msi.PNG 
Views:	2 
Size:	83.5 KB 
ID:	43993
      My ComputerSystem Spec

  7. jds63's Avatar
    Posts : 3,106
    Windows 10 Pro 64 bit
       21 Oct 2015 #47

    Gary said: View Post
    I have an MSI X58-Pro-E Model MS-7522 and the site I used to go to is either changed as I get a 404.
    I have right one, only these 3 boards under that http://us.msi.com/search/MS-7522/product/1


    Other chipset drivers and SATA i would update all that is needed if not already there from Windows 10, as they do carry some of your drivers.
    http://us.msi.com/support/mb/X58_ProE.html#down-driver&Win7%2064


    Says that, but no AHCI drivers, would not trust Live Update as much, but i can not see all you do on system.
      My ComputerSystem Spec

  8. jds63's Avatar
    Posts : 3,106
    Windows 10 Pro 64 bit
       21 Oct 2015 #48

    Drivers for SATA AHCI have to be installed where IDE/SATA controllers are through the Device Manager.

    Listed on site as On-Board SATA AHCI/RAID Drivers Intel Rapid Storage Technology Driver
    In past these drivers are preinstalled before the OS,some will say it can be done post install of the OS.
    Also same said sometimes about changing mode IDE - AHCI after OS install can only be done before OS install.
    Believe this case was for older OS's

    Only way to do it now it this, then switching to AHCI. Extract all files and you can put these on a flash drive and then Right click that controller, select update driver software, select Browse for driver software on your Computer, browse to location on the flash drive an select the one file listed.

    Found this on Eight-Forums
    http://www.eightforums.com/drivers-hardware/22126-changing-ide-ahci-caused-no-boot.html


    As said before will work fine in IDE too, if do not want to try any of this, good luck Gary.
      My ComputerSystem Spec


  9. Posts : 91
    64-bit 10240 10 Pro
    Thread Starter
       21 Oct 2015 #49

    jds63 said: View Post
    Drivers for SATA AHCI have to be installed where IDE/SATA controllers are through the Device Manager.

    Listed on site as On-Board SATA AHCI/RAID Drivers Intel Rapid Storage Technology Driver
    In past these drivers are preinstalled before the OS,some will say it can be done post install of the OS.
    Also same said sometimes about changing mode IDE - AHCI after OS install can only be done before OS install.
    Believe this case was for older OS's

    Only way to do it now it this, then switching to AHCI. Extract all files and you can put these on a flash drive and then Right click that controller, select update driver software, select Browse for driver software on your Computer, browse to location on the flash drive an select the one file listed.

    Found this on Eight-Forums
    http://www.eightforums.com/drivers-hardware/22126-changing-ide-ahci-caused-no-boot.html


    As said before will work fine in IDE too, if do not want to try any of this, good luck Gary.
    Thanks for your help but I think that I will leave well enough alone. The drive is way faster than I had and it is ok. Thanks again.
      My ComputerSystem Spec

  10.    21 Oct 2015 #50

    Hi,

    As said before will work fine in IDE too, if do not want to try any of this, good luck Gary.
    It does make for an appreciable difference though.
    However, once the OS has been installed with the bios set to IDE mode (or legacy, depending on bios), it's pretty tricky to make it accept the change. I ended up reinstalling the OS, all the tricks I found on the web just made the aging machine refuse to boot.

    Anyhow, I guess we'll all be talking PCIe drives within a couple of years. I'm saving up for an Intel 750 as I write.

    That said, Gary obtains a pretty high WINSAT score all things considering.
    @aztec506 ; Thx for sharing. Looks as if we have similar stories, Velociraptor is retired here too. Great little thing as it was back then though.


    Cheers,
      My ComputersSystem Spec


 
Page 5 of 32 FirstFirst ... 3456715 ... LastLast

Related Threads
Solved Samsung Magician in Drivers and Hardware
Samsung Magician Version 5.2.1 80074 ***Important information, please read the pdf*** New Samsung Magician features a number of improvements over version 5.1: New features:
Samsung's 950 Pro SSD in Drivers and Hardware
Source
Trying to install Samsung SmarThru office V2 for my printer/scanner, but Windows 10 reports the signer of the executable is not trusted, I downloaded from the Samsung website and the signer is shown as Samsung. There seems to be no way to bypass...
Like you, I encountered source disk bad sectors error when cloning with Samsung migration software. Resolved by using EaseUS Tool to clone.
Hi guys, i'm using win 10 pro x64 on a samsung evo 850 120gb ssd. My samsung magician just can't recognize the OS, anyone knows how to fix? Thank you and sorry for my bad grammar! :p 39391
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 18:38.
Find Us