USB IrDA devices no longer work in W10

Page 1 of 2 12 LastLast

  1. Posts : 248
    W10 Pro/W7 Pro 64-bit
       #1

    USB IrDA devices no longer work in W10


    Couldn't get my USB IR adapter to work in W10 and found the answer in the link below.

    http://borncity.com/win/2015/09/02/windows-10-infrared-irda-stack-is-removed/
      My Computer


  2. Posts : 248
    W10 Pro/W7 Pro 64-bit
    Thread Starter
       #2

    I had put my email address on a list to get any info about this problem and received this response today.

    ************
    Hi Everyone, Caleb from Coolgear here with an update regarding Windows 10 drivers for your infrared adapters.

    Unfortunately the news isn't good. Our supplier is telling us that they are being stonewalled by Microsoft regarding the changes made in Windows 10 and how to update the driver package. I've also heard from Asix (formerly Moschip), the chip manufacture used in most adapters, that they are also getting similar lack of support from Microsoft regarding this issue.

    All we can recommend at this time is that if using your infrared adapter is important to you, do not upgrade to Windows 10, or keep an older PC around to sync your equipment with. For the more technically inclined among you, a virtual machine using VMWare Player or Oracle VirtualBox is also a solution.

    I would also recommend that you continue to make some noise on the official MicroSoft forums and elsewhere about the issue. Maybe with some pressure from the public Microsoft will at least acknowledge the problem and work towards resolving it.
    ************
      My Computer


  3. Posts : 3,505
    Windows 10 Pro 64-bit 21H1 (May 2021 build 19043.1083)
       #3

    Yes, VMWare supports using USB devices, so in worst case you install an earlier Windows version in a virtual machine and then transfer control of the IrDA device to the virtual. I use the same method to use my very old parallel port Iomega ZIP drive! I have installed Windows 98 in a virtual machine and when I need to access my ZIP disks, I connect the drive to my parallel port and transfer control to Windows 98. Not very convenient, but a good workaround.
      My Computer


  4. Posts : 248
    W10 Pro/W7 Pro 64-bit
    Thread Starter
       #4

    I'm on a dual boot with W7 so I can still use that but the question is, why is MS being so uncooperative?
      My Computer


  5. Posts : 3,505
    Windows 10 Pro 64-bit 21H1 (May 2021 build 19043.1083)
       #5

    IrDA is an old technology and rarely used today, but surely this is not a reason to remove support for it!
      My Computer


  6. Posts : 1
    Windows 10
       #6

    IrDA and other old technologies in Windows 10


    spapakons said:
    IrDA is an old technology and rarely used today, but surely this is not a reason to remove support for it!
    Yes, IrDA is an old technology, but less than half the age of the hardware keyboard. Both have a rapidly diminishing user base, but the core user base of the hardware keyboard includes software engineers, and this is therefore safe for the foreseeable future. The core user base of the IrDA computer interface is not small, but is engaged in physical activities, particularly underwater activities and sports training, a sphere of activity which is largely closed to desk-bound Microsoft operating system engineers and salesmen, so folk who need to upload their dive computer or heart rate/bp logger data to a computer database may have to migrate to Apple when they update their computer systems, unless someone creates a third-party workaround, which has unfortunately proved to be a non-trivial undertaking. It may be that the new ultra-low power Bluetooth technologies may become practical to replace IrDA in these devices at some time in the future, but it would take another 5 - 10 years to phase out IrDA in dive computers.
      My Computer


  7. Posts : 248
    W10 Pro/W7 Pro 64-bit
    Thread Starter
       #7

    I read up on the dive computers. Lots of pissed off people that have $1000+ hardware that doesn't work with W10 but did prior to the final release.
      My Computer


  8. Posts : 3,505
    Windows 10 Pro 64-bit 21H1 (May 2021 build 19043.1083)
       #8

    Just wondering, can't one just copy the relevant driver files (INF, DLLs) from a Windows 7 or 8.1 installation and try to manually install then through the Device Manager? For each unknown device relative to the IrDA controller, just browse to the folder that contains all the files and hopefully you will finally manage to make it work. I would install Windows 7 or 8.1 in another disk, or virtual machine and then find out (from device properties) which are the relevant files. I would simply copy them in a folder and try them in Windows 10. Nothing to lose.
      My Computer


  9. Posts : 248
    W10 Pro/W7 Pro 64-bit
    Thread Starter
       #9

    I think that it's more than just files. Windows says that one has the latest drivers. I'm on a dual boot with W7 so I can use that. It's just strange that it worked supposedly up to the final release at which time, code was removed.
      My Computer


  10. Posts : 3,505
    Windows 10 Pro 64-bit 21H1 (May 2021 build 19043.1083)
       #10

    Maybe there are no drivers for it included in Windows 10, but you can connect it and then browse for drivers in Windows\Inf and Windows\System32 folders of your Windows 7 installation and it might install and work. I would try that.

    I had done the same trick for my old parallel port Iomega ZIP-100 drive. Officially Iomega has dropped support for it in Windows Vista and later. But I have detected the relevant driver files in a Windows XP installation, copied them in a folder and managed to manually install it in Vista 32-bit and Windows 7 32-bit. Unfortunately Microsoft has changed the drivers of the parallel port in Windows 8 and 10, so it is not detected at all and I cannot install it manually any more. I could try to add it as a legacy device, but not sure if it will work or give a BSOD.


    EDIT: Have you read the following line from the link in your original post?

    "In the past, many vendors are using the IrDA stack, implemented in Windows. So USB infrared receivers don’t need their own drivers or IrDA stack. It simply works. Now Microsoft has removed the IrDA stack in Windows 10 RTM, so all USB infrared receivers/devices are bricked. Only, if a vender already has implemented its own IrDA stack and provides Windows 10 compatible software, the infrared receiver/devices may work."

    So try the manual installation as I describe above and it might work for your device!
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 05:59.
Find Us




Windows 10 Forums