New
#11
click in the searchbox and type cmd
In the opening window select command prompt run as administrator
click in the searchbox and type cmd
In the opening window select command prompt run as administrator
Sorry Pentagon I was waiting for a reply from you and failed to notice that it had opened a second page and the reply was on that. I have just copied the result.
I am closing down now for the night but will look in tomorrow if you wouldn't mind replying in the mean time.
Windows Boot Manager
--------------------
identifier {bootmgr}
device partition=\Device\HarddiskVolume1
path \EFI\MICROSOFT\BOOT\BOOTMGFW.EFI
description Windows Boot Manager
locale en-GB
inherit {globalsettings}
default {current}
resumeobject {c889dd2b-1e7b-11ee-9155-88ff85ed28ea}
displayorder {current}
toolsdisplayorder {memdiag}
timeout 30
Windows Boot Loader
-------------------
identifier {current}
device partition=C:
path \WINDOWS\system32\winload.efi
description Windows 10
locale en-GB
inherit {bootloadersettings}
recoverysequence {c889dd2d-1e7b-11ee-9155-88ff85ed28ea}
displaymessageoverride Recovery
recoveryenabled Yes
isolatedcontext Yes
allowedinmemorysettings 0x15000075
osdevice partition=C:
systemroot \WINDOWS
resumeobject {c889dd2b-1e7b-11ee-9155-88ff85ed28ea}
nx OptIn
bootmenupolicy Standard
OK, your active EFI is on Disk 0 and your C-Partition is on Disk 1.
To find out which Recovery you use type:
Cmd (admin)
C:\Windows\System32>reagentc /info
and post the result
Sorry missed last night.
C:\WINDOWS\system32>reagentc /info
Windows Recovery Environment (Windows RE) and system reset configuration
Information:
Windows RE status: Enabled
Windows RE location: \\?\GLOBALROOT\device\harddisk1\partition3\Recovery\WindowsRE
Boot Configuration Data (BCD) identifier: c889dd2d-1e7b-11ee-9155-88ff85ed28ea
Recovery image location:
Recovery image index: 0
Custom image location:
Custom image index: 0
REAGENTC.EXE: Operation Successful.
COPY & PASTE each command step by step
C:\Windows\System32>
reagentc /disable
diskpart
sel disk 0
sel par 4
delete partition override
sel par 3
extend
sel disk 1
sel par 3
delete partition overide
sel par 2
extend
shrink minimum=1025
create partition primary
format quick fs=ntfs label="Recovery"
set id="de94bba4-06d1-4d40-a16a-bfd50179d6ac"
gpt attributes=0x8000000000000001
exit
reagentc /enable
You are ready and the Windows Update will not produce any error message
The unused EFI-Partition on disk 1 can be treated later
And see the change in Diskmanagement when you are ready.
Drive Letters like C; D; E; can be changed here also
Assign a Drive Letter to your last Partition (5) on Disk 1. Just RightClick on the Partition and you find it.
Then run cmd command admin
reg query HKLM\SYSTEM\CurrentControlSet\Control /v FirmwareBootDevice
reg query HKLM\SYSTEM\CurrentControlSet\Control /v SystemBootDevice
Last edited by Pentagon; 1 Week Ago at 12:46.
Hi Pentagon,
I did as you said, one at a time and waited for each response, (I have a copy) but it all looked ok till I did the last line
C:\WINDOWS\system32>reagentc /enable
I was met with
REAGENTC.EXE: The Windows RE image was not found.
I thought best not to continue to entering the REG queries.
Have I missed something?
can you post a new screenshot of your "Diskmanagement" to check the result
I hope you didn't forget the first command (reagentc /disable)
The 2 reg-commands are just to controll everything once more. They don't change anything.
Type
C:\Windows\System32>dir /a /s c:\Windows\System32\winre.wim
to find the lost WinRE.wim
Last edited by Pentagon; 1 Week Ago at 16:46.
I am trying to post a snipped shot of the disk management but it just ignores me when I click upload?
It loads into my word processor program ok?
- - - Updated - - -
I have added it as an attachment?
I did do /disable
where did you get the set id="de94bba4-06d1-4d40-a16a-bfd50179d6ac" from?
C:\WINDOWS\system32>dir /a /s c:\Windows\System32\winre.wim
Volume in drive C has no label.
Volume Serial Number is C4F0-C1A8
File Not Found
C:\WINDOWS\system32>
Last edited by Pentagon; 1 Week Ago at 17:16.
Yes click on the one marked 'insert image' I get the insert image page, click 'from computer/choose file, the file appears in the box and when I click upload nothing happens?
I did it a few times even with a smaller version of the screen ands altering the file toi a jpg from a png still nothing when I clicked upload?
- - - Updated - - -
there is no option for assign a letter for that partition the only two that are not greyed out are 'delete volume' and 'help'