Attn. SSD owners - Enabling AHCI mode AFTER Windows 10 installation.

Page 1 of 9 123 ... LastLast

  1. Posts : 4
    Win 10 Professional 64-bit
       #1

    Attn. SSD owners - Enabling AHCI mode AFTER Windows 10 installation.


    Hello everybody. What started out as a request for guidance ended up with me solving my own problem. Thought I may as well pass on my findings anyway just in case it helps somebody else in the same situation.

    So over the weekend, through a series of upgrades, I successfully hopped from Vista to Windows 10 Professional 64-bit. But, as is not unusual, I again managed to snatch defeat from the jaws of victory. With my new SSD loaded with Win 10 goodness, I realised I was still operating it in IDE mode. A confident dip into the BIOS to enable AHCI mode resulted in Windows then failing to start because it no longer recognised the boot drive! I'm guessing the AHCI driver wasn't loaded during installation since the mode wasn't in use. So back to IDE mode and a surf around for solutions. Plenty around pertaining to Vista, Win 7 and Win 8 involving changing registry values but nothing tangible for Win 10. However I found this alternative Win 8 workaround which I can confirm works equally well in Windows 10. I realise I'm probably teaching my Grandmother to suck eggs with this post here but perhaps somebody as equally technophobic as me, may find it useful. This is what I did:

    1. Run Command Prompt as Admin
    2. Invoke a Safe Mode boot with the command: bcdedit /set {current} safeboot minimal
    3. Restart the PC and enter your BIOS during bootup.
    4. Change from IDE to AHCI mode then Save & Exit.
    5. Windows 10 will launch in Safe Mode.
    6. Right click the Window icon and select to run the Command Prompt in Admin mode from among the various options.
    7. Cancel Safe Mode booting with the command: bcdedit /deletevalue {current} safeboot
    8. Restart your PC once more and this time it will boot up normally but with AHCI mode activated.
    9. Bask in the reflected glory of being a total Windows 10 God

    Last edited by Brink; 26 Feb 2016 at 00:54. Reason: added tip
      My Computer


  2. Posts : 200
    Wds10 - OEM
       #2

    Was it brand new SSD you replaced ...or old one just upgrading to wds 10...?
    Because i have SSD with wds8.1 ..upgraded to wds10 .. did not see any problems ...!
      My Computers


  3. Posts : 4
    Win 10 Professional 64-bit
    Thread Starter
       #3

    My SSD was brand new and in my excitement to get the upgrading process underway, I forgot that AHCI mode should be enabled BEFORE the OS is loaded on the drive. I guess this is so the OS can install the appropriate driver after doing its hardware check. The SSD worked in IDE mode but to release the full potential of the drive, it needs to operate in AHCI mode. A straightforward upgrade would not be a problem providing the SSD was already working in AHCI mode.
      My Computer


  4. Posts : 150
    Win 10 64
       #4

    Attn. SSD owners - Enabling AHCI mode AFTER Windows 10 installation.

    Yesss.... It work
    Many thanks to have published the solution

    Martin
    Montreal, Canada
      My Computer


  5. Posts : 51
    Win 10
       #5

    Toolbad: Thanks for the info.
      My Computer


  6. Posts : 1,481
    W10 22H2 19045.3031
       #6

    TooBad, great info. Was gong to try this on my puter and under bios I have 2 options. Don't know if I need to do both or just one?? My options are:
    OnChip SATA type IDE or ACHI
    OnBoard SATAII Ctrl Mode IDE or ACHI

    Tx...
      My Computers


  7. Posts : 4
    Win 10 Professional 64-bit
    Thread Starter
       #7

    I'd guess you would want to enable AHCI mode in the SATA II controller on the motherboard and use that. The transfer rate for SATA is only 1.5Gb/s whilst SATA II whizzes along at 3Gb/s. Hopefully somebody more knowledgeable will pop by with a definitive answer for you. Hope it all works out.
      My Computer


  8. Posts : 1,481
    W10 22H2 19045.3031
       #8

    Toobad said:
    I'd guess you would want to enable AHCI mode in the SATA II controller on the motherboard and use that. The transfer rate for SATA is only 1.5Gb/s whilst SATA II whizzes along at 3Gb/s. Hopefully somebody more knowledgeable will pop by with a definitive answer for you. Hope it all works out.
    I tried it....it works. Tx again
      My Computers


  9. Posts : 1
    Windows 10
       #9

    I tried this and now it says Inaccessible Boot Device and it just keeps rebooting in this endless loop. Not sure what to do
      My Computer


  10. Posts : 1
    Windows 10
       #10

    I can confirm that this method works in Windows 10 64-bit. Thanks to the OP for all the research and hard work.

    Safe mode must have some sort of script to fix a "false" IDE flag, when really you're just switching to AHCI.

    Running 850 EVO 500 GB SSD boot drive and 840 EVO 120 GB SSD.
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 03:28.
Find Us




Windows 10 Forums