Windows 10: Windows corrupt, main hard drive partition not detected

Page 1 of 2 12 LastLast

  1. Posts : 65
    Windows 10-64 bit (version 1607 build 14393.1944)
       16 Jan 2018 #1

    Windows corrupt, main hard drive partition not detected


    I have Windows 10-64 bit (version 1607 build 14393.1944). Upon starting my pc, I am getting the following error on a blue screen in white font.

    Recovery
    Your PC/Device needs to be repaired
    A required device isn't connected or can't be accessed.
    Error code: 0xc000000e
    You'll need to use recovery tools. If you don't have any installation media (like a disc or USB device), contact your PC administrator or PC/Device manufacturer.

    Press Enter to try again (Pressing Enter merely refreshes the screen (i.e. does nothing for me)
    Press F8 for Startup Settings (Pressing F8 also merely refreshes the screen (i.e. does nothing for me)

    I made a bootble usb for windows 10 and tried:
    - startup repair - 'startup repair couldn't fix your pc'
    - system restore - 'system restore couldn't find the offline boot volume'
    - go back to a previous build - 'we ran into a problem and wont be able to take you back...try resetting your pc'

    When I checked in the bios boot device priority, my hard drive (500 GB) was not listed. I had attached an old SATA internal hard drive (10-11 years old) of 80 GB capacity which was being used just for storage purposes. This 80GB hard drive was being listed in BIOS boot priority settings.

    This hard drive was also listed when I pressed the F7 key and got a menu to choose boot device and chose windows 10 bootable usb to initiate the advanced settings menu.

    When I began with windows 10 installation and chose the upgrade option , I got the message “The upgrade option isn’t available if you start your computer using windows installation media”.
    Then I chose the clean install option. In the menu I was getting the following partitions

    C: drive – 100Mb system reserved
    E: drive – (The 80 gb hard drive, i.e. the old hard drive)

    That’s it. My system is not recognizing the partition of the 500GB hard drive. It had two partitions


    C: partition was used for software instllation
    G: partition was used for files and folders storage.


    I also interchanged the cables of my two hard drives and started my PC, but the same issue was being observed.


    I hope that if this 100mb system reserved is showing, my 500gb hard drive is not damaged. What should I do to boot my system normally?


    I don't want to reformat and lose all my files and programs so please do not suggest that.
      My ComputerSystem Spec

  2.    16 Jan 2018 #2

    Hi,
    1. I'm guessing your disk may be a bit elderly, so need to do basic checks.

    Please download and create Kyhi's bootable disk from the top of the Software and Apps section here. This boots to a special version of Win 10 and offers a range of utilities as you can see in the screenshot there.

    Boot your PC from that, and run HDTune from that disk. Post a screenshot showing the Health tab.
    To post a screenshot please use the icon to the left of the video icon above your post)
    my 500gb hard drive is not damaged.
    - I note you say that- we don't know how you established that.

    2. Then run Minitool Partition Wizard and post a screenshot of that showing all disks, and expanding all columns as necessary so all text is visible.

    3. I also note your Windows build is 2 major builds out of date. Have you disabled Windows update, or has it just been broken for a long time, or have upgrades failed?

    4.
    I don't want to reformat and lose all my files and programs so please do not suggest that.
    One excellent way to reduce the probability of that is to routinely use disk imaging. E.g. Macrium reflect (free) + external storage for disk images. We repeatedly recommend that and all regular contributors here do this.

    Do you have any disk images?
    If so, that would probably be the easiest way to restore your system - maybe the only one.

    Finally, if partitions are missing, this suggests either
    - your disk is irretrievably damaged or corrupt
    or
    - maybe you need to use a utility program to rebuild your partition table.
      My ComputerSystem Spec


  3. Posts : 65
    Windows 10-64 bit (version 1607 build 14393.1944)
    Thread Starter
       16 Jan 2018 #3

    dalchina said: View Post
    Hi,
    1. I'm guessing your disk may be a bit elderly, so need to do basic checks.

    Please download and create Kyhi's bootable disk from the top of the Software and Apps section here. This boots to a special version of Win 10 and offers a range of utilities as you can see in the screenshot there.

    Boot your PC from that, and run HDTune from that disk. Post a screenshot showing the Health tab.
    To post a screenshot please use the icon to the left of the video icon above your post)
    - I note you say that- we don't know how you established that.

    2. Then run Minitool Partition Wizard and post a screenshot of that showing all disks, and expanding all columns as necessary so all text is visible.

    3. I also note your Windows build is 2 major builds out of date. Have you disabled Windows update, or has it just been broken for a long time, or have upgrades failed?

    4.

    One excellent way to reduce the probability of that is to routinely use disk imaging. E.g. Macrium reflect (free) + external storage for disk images. We repeatedly recommend that and all regular contributors here do this.

    Do you have any disk images?
    If so, that would probably be the easiest way to restore your system - maybe the only one.

    Finally, if partitions are missing, this suggests either
    - your disk is irretrievably damaged or corrupt
    or
    - maybe you need to use a utility program to rebuild your partition table.






    I had disabled automatic updates. The last update did not occur and was ending in failure. The last I restarted my pc, it downloaded the update and I kept postponing it. I just used to hibernate my PC for fast reboots.


    The reason I said that my 500gb hard disk isn't damaged because 100mb partition is a system partition and this 500gb hard disk was being used as a system partition only. (i.e. the c partition of it).

    Therefore, I believe that 100mb partition is a part of this hard disk only.


    I don't have any disk images. I am attaching the screenshots. Both minitool and hd tune could not identify my hard drive partition at all.


    Click image for larger version. 

Name:	HDTUNE 1.png 
Views:	45 
Size:	29.1 KB 
ID:	172818
    Click image for larger version. 

Name:	SCREEN2.png 
Views:	45 
Size:	22.1 KB 
ID:	172821
    Click image for larger version. 

Name:	1.jpg 
Views:	2 
Size:	187.9 KB 
ID:	172817
    Click image for larger version. 

Name:	HDTUNE 2.png 
Views:	45 
Size:	29.8 KB 
ID:	172819
    Click image for larger version. 

Name:	MINITOOL SCREENSHOT.png 
Views:	6 
Size:	381.9 KB 
ID:	172820
      My ComputerSystem Spec

  4.    16 Jan 2018 #4

    Not clear what your doing the 500gig was the one with windows on it correct? It's not showing in the bios so it's dead if you tried different cables port. So the 80 gig what are you trying to do with it? It's drive doesn't show in the bios nothing can be done to recover it other than sending it to a recovery firm
      My ComputerSystem Spec

  5.    16 Jan 2018 #5

    You can try putting your 500Gb drive in a drive caddy (different connections, hardware) and seeing if it spins up or makes strange noises.. if it does nothing, then as Samuria says, it's dead.

    After that you're into risky and improbable arcane measures like putting it into a freezer (beware of condensation) and tricks like that some say have sometimes got drives working.
      My ComputerSystem Spec

  6.    16 Jan 2018 #6

    Assume that the cables have actually been checked? they do on occasions come loose, the solder joints on the circuit board on old drives sometimes fail as well, PATA power connectors are a favourite failure spot.
    If it's an old PATA drive, sounds like it may be, check any jumpers are present and haven't dropped off.
    Not recommended but the freezer trick does sometimes work but only if there is an overheating chip problem, however I prefer finding the offending chip, if that is the cause and temporarily clamping a heat sink on it, gives you a bit more time to get any data off. However if cables are OK and the Bios is failing to detect it and or the drive isn't spinning up, nothing you can do yourself is going to work.
      My ComputersSystem Spec

  7.    16 Jan 2018 #7

    archz2 said: View Post
    ...The reason I said that my 500gb hard disk isn't damaged because 100mb partition is a system partition and this 500gb hard disk was being used as a system partition only. (i.e. the c partition of it).

    Therefore, I believe that 100mb partition is a part of this hard disk only. ...
    I'm not sure I get exactly what you're saying here but, just in case: the 100mb partition is not part of any 500GB disk but is on the 80GB disk.
      My ComputerSystem Spec


  8. Posts : 65
    Windows 10-64 bit (version 1607 build 14393.1944)
    Thread Starter
       4 Weeks Ago #8

    Okay, I took out my hard drive and saw the ports are blackened out. I had ordered a hard drive case from Amazon 4 days ago which arrived today. I plugged my hard drive into it, connected the USB and powered on the adapter, the hard drive wasn't moving at all.

    This is the condition of that hard drive. Its ports are blackened out. Now what should I do?


    Click image for larger version. 

Name:	27045199_2037441249614220_1141914390_n.jpg 
Views:	3 
Size:	117.3 KB 
ID:	173897
      My ComputerSystem Spec

  9.    4 Weeks Ago #9

    Put it in the bin something has burnt out it's not worth repairing
      My ComputerSystem Spec

  10.    4 Weeks Ago #10

    Thanks for following up with what you found out archz2. While it's unfortunate that the disk ought to be securely (sledge hammer? ) binned, we appreciate when you come back and report on the outcome.
      My ComputerSystem Spec


 
Page 1 of 2 12 LastLast

Related Threads
It has its own power supply, and I've tried the front and back USB ports on my tower. The lights are all on, and I can hear the hard drive itself running, and yet the computer doesn't detect it in any way. The hard drive is a 250GB Maxtor IDE...
Hello Short story. Western Digital Elements Drive 3TB use for back up and today wouldn't power. Swapped all cables no luck. Removed hard drive from Caddy housing and mounted in rig direct to motherboard. The hard drive is readable but appears...
I have two WD hard drives with the OS installed on one and the other is for storage. All this started with a hard shut down when the PC froze and then after the restart Windows wouldn't boot at all. It was stuck at the Windows logo for a very long...
I bought a new ssd for my computer but i still havn't installed anything on it yet. I would like to know if i will have problems or will it be as easy to install and run normaly as the youtube videos show. On my main hard drive i had windows 7 but...
I got this drive image from my Macrium Reflect Home edition and don't understand the last partition? is there something wrong here? Thanks! :)
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 08:41.
Find Us