Slow boot/shutdown/restart after installing a USB 3.0 PCI-E card

Page 1 of 3 123 LastLast

  1. Posts : 180
    Windows 10 Pro v.20H2 OS Build 19041.662
       #1

    Slow boot/shutdown/restart after installing a USB 3.0 PCI-E card


    I have a HP Z400 workstation which I bought in 2010. It supports a two-port USB 3.0 card which I had installed until recently. It was the one that HP recommended. However, it stopped working and I replaced it with a different one, specifically an Anker card.

    I now have a problem because the PC is very slow when booting. The power button lights up, remains lit for 45 seconds to 1 minute and then the normal boot process begins. Logging on is also very slow. The same applies when shutting down or restarting. There is a very big delay.

    Are there any suggestions as to how to cut down these delays?
      My Computer

  2. Caledon Ken's Avatar
    Posts : 24,448
    Windows 10 Pro x64 Version 2004
       #2

    If you remove card does it boot normally?

    What is connected to these two new ports? Does it boot normally if you disconnect items?

    Have you tried a different slot?


    Ken
      My Computer


  3. Posts : 180
    Windows 10 Pro v.20H2 OS Build 19041.662
    Thread Starter
       #3

    Caledon Ken said:
    If you remove card does it boot normally?
    What is connected to these two new ports? Does it boot normally if you disconnect items?
    Have you tried a different slot?
    Thank you for suggestions. After removing the card the boot process was fast. There was no delay before the POST and the login screen came up quick. I should add that I am quite sure that the card was properly placed in the slot. I had removed it and placed it again, earlier, to make sure that it was properly set in the slot.

    I have a 7-ports USB hub connected to one of the ports to which I conncted a webcam and two extrenal drives. On the other port I have another external drive directly connected to it.

    Unfortunately I don't have spare slot to connect the card to it.
      My Computer

  4. Caledon Ken's Avatar
    Posts : 24,448
    Windows 10 Pro x64 Version 2004
       #4

    Are you using Windows Fast Boot?

    Have you checked you BIOS for boot order. Could be it is checking USB devices first, and you said there were two, then coming to HDD / SDD.

    See if you can prioritize your SSD / HDD as first drive to check.
      My Computer


  5. Posts : 180
    Windows 10 Pro v.20H2 OS Build 19041.662
    Thread Starter
       #5

    I an using Windows Fast Boot. I tried disabling it, but there was no difference.
    According to my BIOS settings my SDD drive (C drive) has priority over other hard disk drives, then over USB.

    A couple of things that may be important are: The Anker card has 2 USB ports, but also a 20-pin Connector (can expand another two USB 3.0 ports). The HP manual mentions that I could add a card supporting 2 USB 3.0 ports. I wonder if the additional feature is complicating things.

    The other point is that the biggest delay that I notice is a black screen before the screen that comes up on boot that gives me the option to enter Setup or choose the boot order for the particular session. I wonder what the PC is doing at the very beginning, before the power on screen appears.
      My Computer

  6. Caledon Ken's Avatar
    Posts : 24,448
    Windows 10 Pro x64 Version 2004
       #6

    If you disconnect everything from card does it boot faster?
      My Computer


  7. Posts : 180
    Windows 10 Pro v.20H2 OS Build 19041.662
    Thread Starter
       #7

    Caledon Ken said:
    If you disconnect everything from card does it boot faster?
    There is a small improvement. I removed the USB hub and the external disk from the two USB ports and the time taken after power on until the option to enter Setup or choose the boot order for the particular session, was shortened to about 40 seconds (from 1 minute). This compares to practically less than 3 seconds when I used the previous USB card which unfortunately doesn't work any more.
      My Computer

  8. Caledon Ken's Avatar
    Posts : 24,448
    Windows 10 Pro x64 Version 2004
       #8

    Went to Anker.

    They have a driver page and a forum. Not having model I was stumped.

    Wondering if Windows has correctly id device and loaded Anker drivers?
      My Computer


  9. Posts : 180
    Windows 10 Pro v.20H2 OS Build 19041.662
    Thread Starter
       #9

    Caledon Ken said:
    Went to Anker.
    They have a driver page and a forum. Not having model I was stumped.
    Wondering if Windows has correctly id device and loaded Anker drivers?
    The one I have is shown at https://www.anker.com/products/varia...8UPPCIE-2S20PU
    I notice that the box the card came in indicates that it is "Compatible with Windows XP / Vista / 7". Perhaps it doesn't work with Windows 10? The reviews on that page mention that it does work with Windows 10...

    How could I check the id device in Windows?
      My Computer

  10. Caledon Ken's Avatar
    Posts : 24,448
    Windows 10 Pro x64 Version 2004
       #10

    Right click start, left click device manager. Find adapter, right click, click properties, then driver tab. If your device has vendor specific drivers I would think the vendors name you be there and not a generic Microsoft driver.


    EDIT:

    So looking at install instruction they state install card and load driver.

    Is that what you did?
      My Computer


 
Page 1 of 3 123 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 12:57.
Find Us




Windows 10 Forums