The Raspberry Pi Thread [4]

  1. caperjack's Avatar
    Posts : 4,185
    insider build 10586.3 win10 pro 64
       #1741

    yupp the pi zero one is easy to break off ,speaking from experience ,lol
    alphanumeric said: View Post
    Ok, I haven't tried to get it off yet, I may just put a big X on it with a sharpie and set it aside. Then if I break one on my working camera, then have a go at removing it.
    The locking bar on the Zero's is even smaller and from what I see posted on the PI forum, even easier to break.
    You want to be real careful with those ones.
    I don't have those camera's, but I have the cable to hook up a regular sized camera to a Zero.
    Several actually, I think you get one with the official Pi Zero case?
      My ComputerSystem Spec

  2.    #1742

    Mine seem to vary quit a bit. One day I'm getting 20 something fps then another day its less than 10? Likely my WIFI and whats in use at the same time. I have a wireless router thats not in use that I may setup just for my rspbery Pi's.

    So far so good, no hits of any streaks on the camera that "had" that issue. Need to wait another hour of more to be 100% certain though.
      My ComputerSystem Spec

  3.    #1743

    Hey Jack I think that fixed my camera issue. Just when I should have been watching I got side tracked. It's dark now but the image looks OK. No signs of streaking or wierdness. I would normally see all kinds of grey virtical streaks by now. Looks like it was the lens / light sensor part of mine that glitched.
    I own you a favor for fixing me up with your camera parts. I'll double check it in the morning but I think I'm good now.
      My ComputerSystem Spec

  4. caperjack's Avatar
    Posts : 4,185
    insider build 10586.3 win10 pro 64
       #1744

    thats great ,,part payment for all the knowledge and code you pass my way ,,,Thanks
    alphanumeric said: View Post
    Hey Jack I think that fixed my camera issue. Just when I should have been watching I got side tracked. It's dark now but the image looks OK. No signs of streaking or wierdness. I would normally see all kinds of grey virtical streaks by now. Looks like it was the lens / light sensor part of mine that glitched.
    I own you a favor for fixing me up with your camera parts. I'll double check it in the morning but I think I'm good now.
      My ComputerSystem Spec

  5.    #1745

    The dog got me up early so I'm just sitting here waiting for the sun to rise, lol. Usually that camera would be all full of grey streaks down both sides righ about now. Nice and clean looking at the moment. Only the one street light lit so really had to see anything. I'll know for sure its fixed in about half an hour or so. It's 6:30 and the sun will rise around 7 ish. This camera is the only one curently looking outside. And the only one to get any bright sunlight.

    EDIT: Suns just coming up, nice clear image.
    Last edited by alphanumeric; 27 Jan 2019 at 05:58.
      My ComputerSystem Spec

  6. caperjack's Avatar
    Posts : 4,185
    insider build 10586.3 win10 pro 64
       #1746

    alphanumeric said: View Post
    The dog got me up early so I'm just sitting here waiting for the sun to rise, lol. Usually that camera would be all full of grey streaks down both sides righ about now. Nice and clean looking at the moment. Only the one street light lit so really had to see anything. I'll know for sure its fixed in about half an hour or so. It's 6:30 and the sun will rise around 7 ish. This camera is the only one curently looking outside. And the only one to get any bright sunlight.

    EDIT: Suns just coming up, nice clear image.
      My ComputerSystem Spec

  7.    #1747

    Woot, was just looking at the new products and noticed this, https://shop.pimoroni.com/products/z...e-sensor-array on Pimoroni.
    And I'm just getting ready to order some stuff. I was going to have to order that separately from the manufacturer and pay another shipping fee to get it. I already have the Zumo chassis, Arduino shield, and the Arduino UNO. Went to the Zumo site for install instructions and noticed I didn't have that part, then wanted it, lol. For once I wasn't in a hurry to order my stuff, and things happened in my favour. =)
      My ComputerSystem Spec

  8. caperjack's Avatar
    Posts : 4,185
    insider build 10586.3 win10 pro 64
       #1748

    only 9 left ,better hurry ,lol
      My ComputerSystem Spec

  9.    #1749

    Just got the order received e-mail, so one of those should be taged as mine. It should ship in the morning. That will let my ZUMO rover do line following. I'll put some of that blue painters tape down for testing. Its low tack and easy to remove after wards. Thats after I do all the programing. Its C+ on the Arduino. I'll just do what I did when I got my first Raspberry Pi and copy any example code I can find to start things off. I also ordered one of those VL53L1X Time of Flight (ToF) Sensor Breakouts. I hope to use that for collision avoidance. https://shop.pimoroni.com/products/vl53l1x-breakout Assuming it will work with an Arduino.
      My ComputerSystem Spec

  10. caperjack's Avatar
    Posts : 4,185
    insider build 10586.3 win10 pro 64
       #1750

    right on ,will be watching for the video when its all done
    alphanumeric said: View Post
    Just got the order received e-mail, so one of those should be taged as mine. It should ship in the morning. That will let my ZUMO rover do line following. I'll put some of that blue painters tape down for testing. Its low tack and easy to remove after wards. Thats after I do all the programing. Its C+ on the Arduino. I'll just do what I did when I got my first Raspberry Pi and copy any example code I can find to start things off. I also ordered one of those VL53L1X Time of Flight (ToF) Sensor Breakouts. I hope to use that for collision avoidance. https://shop.pimoroni.com/products/vl53l1x-breakout Assuming it will work with an Arduino.
      My ComputerSystem Spec


 

Related Threads
The Raspberry Pi Thread [3] in Chillout Room
Continued From - The Raspberry Pi Thread - Page 208 - Windows 10 Forums A black version of the Pi Zero case would be nice. Or white even.
The Raspberry Pi Thread [2] in Chillout Room
Continued from - The Raspberry Pi Thread - Windows 10 Forums (200 page limit) Looks like my error message is Configuring network interfaces... ioctl: Operation not permitted. I also get a ioctl: invalid argument, I get two of them, whatever...
Hello ladies andgents! :cool: @z3r010 from SevenForums pointed mehere to share this project, but since I don't want to interrupt yourdiscussions on The Raspberry Pi Thread , I thought it would be better to create a new thread. :) It's a cool...
The Raspberry Pi Thread in Chillout Room
After spaming this thread , https://www.tenforums.com/windows-10-news/3950-new-raspberry-pi-2-now-windows-10-support.html I figured a new thread may be in order. I have a B+ and one of the new model 2 B's. I just fired up Raspbian on the new one to...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 12:31.
Find Us