After a recent update, On wake up I am told that "attempted to write to read only memory"
I have looked at the debug file and it says that a driver is at fault.
How do I identify it and how do I replace it and from where?
Warning
Please make a backup of your important files and get your rescue media or create one.
Please create a restore point.
Please follow this tutorial to run driver verifier.
Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.
Driver verifier should be performed for a max of 48 hours, or when you have a bluescreen, whatever comes first.
If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.
Note
Your system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.
Run the tests on all hard drives/partitions!
Please run HDTune first, in the order posted!
Run HDTune to
- check the health,
- scan for errors, no quick scan but full scan
- run a benchmark.
It may take some time, but please take the time you need to perform it properly.
When above is done please make screenshots of the following
- the health,
- the error scan,
- the benchmark incl. following
- transfer rate,
- access time,
- burst rate,
- cpu usage.
Run the long test.
Do not run SeaTools on an SSD as the results will be invalid.
Make a photo of the result and post it.
Disk Check - Windows 7 Help Forums
Use option TWO with parameter /r
Upload the chkdsk log
Code:BugCheck BE, {ffff800028c05178, 8a00000000800121, ffff80002e11eca0, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:BugCheck BE, {ffffe200ca602178, 8a00000000800121, ffffe200ce30d2e0, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:BugCheck BE, {ffffa6015e607178, 8a00000000800121, ffffa6016060dca0, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:BugCheck BE, {ffff9e8130402178, 8a00000000800121, ffff9e81312802e0, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:BugCheck BE, {ffffc40016802178, 8a00000000800121, ffffc4001c49d2e0, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:BugCheck BE, {ffff95009ba02178, 8a00000000800121, ffff95009d7a8130, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:BugCheck BE, {ffff9681aee06178, 8a00000000800121, ffff9681b2cc82e0, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:BugCheck BE, {ffffb18103e06178, 8a00000000800121, ffffb18106346200, b}*** WARNING: Unable to verify checksum for win32k.sysProbably caused by : memory_corruptionCode:Windows failed to resume from hibernate with error status 0xC0000001.Code:The Avira Web Protection service depends on the Avira Real-Time Protection service which failed to start because of the following error: After starting, the service hung in a start-pending state.Code:The device, \Device\Harddisk3\DR3, has a bad block.
Open administrative command prompt and type or copy and paste:
1) winver (in the pop up about windows > view your windows version and build > type this information into the thread)
2) sfc /scannow
3) dism /online /cleanup-image /restorehealth
4) powercfg.exe /hibernate off
When these have completed > right click on the top bar or title bar of the administrative command prompt box > left click on edit then select all > right click on the top bar again > left click on copy > paste into the thread
5) chkdsk /r (this may take many hours, plan to run overnight)
Read Chkdsk Log in Event Viewer in Windows 10 Windows 10 Performance Maintenance Tutorials
CHKDSK: What is it and how do I run it? - Ask Leo!
How do I see the results of a CHKDSK that ran on boot? - Ask Leo!
How to find chkdsk results in Windows 10 - Winaero uses 26226 find
6) Run a SMART tests on your HD and when it is complete please post images into the thread of the drive and the data.
http://www.hdtune.com/
7) run Sea tools for windows using SMART, short and long generic and report result into the thread.
http://www.seagate.com/support/downl...ls-win-master/
How to use SeaTools for Windows
Rule 4
No piracy or discussion of piracy allowed at all. Such as software, music, videos and other intellectual property violations (e.g. downloading youtube videos locally etc) - it is forum policy that no help shall be given to people who knowingly steal software or services.
One of the main reasons for this is that the act of pirating the software will inevitably change the working of the software and make investigation and repair impossible. Please install a legitimate copy of the software and if you are still experiencing the issue we will be please to assist - No further assistance will be provided until we are satisfied that the software is genuine.
@BOSDHunter
My version of windows 10 Pro was an upgrade from a genuine and registered Windows 7 Pro.
I have the disk here.
Theres a tool which is used to bypass the activation of microsoft products. If you are sure you did not use a tool like this, maybe a friend or store tech did it without your knowledge.
Quote