Frequent BSOD memory_management

redlum · 11 Jun 2017

Hi, thanks again for your replies.

1. Ram modules are identical and bought in a pack 4x4gb
2. Malwarebytes is gone
3. BIOS is the latest
4. My Samsung SSD is SM951 M2 ACHI MZHPV256HDGL. Apparently as this is OEM there are no official firmware updates for this although I have seen sites with work around. Not sure what to do about this.
5. I performed all these checks and the system seemd to pass them all.

As I was uninstalling Malwarebytes (probably coincidence) the computer suddenly restarted. After this initial restart the machine began to restart more and more frequently to the point where it couldn't even get past the bios screen. After leaving the machine off for a while it would make it to windows but eventually it would restart and the frequency of restarts would increase again. Even if I left it in the BIOS it would eventually restart itself.

I stripped the machine down and decided to replace the PSU ( a gold rated Seasonic) with another (Super Flower gold rated) and this stopped the restarting.

I was wondering... could an unstable PSU cause the memory management BSODs? It's too early to tell perhaps but after the PSU replacement I received another BSOD "IRQL_NOT_LESS_OR_EQUAL" - I have attached the minidump for this.

I feel like maybe we're getting close?

Many thanks
George

IRQL_NOT_LESS_OR_EQUAL BSOD:
Attachment 138979

Ztruker · 11 Jun 2017

Nothing useful in the dump unfortunately.

What do you have connected to your computer?
What mouse, keyboard?
Any USB devices? If so what are they.
Do you have a knock off Xbox controller?

What I suggest is to disconnect everything you can and if possible replace the mouse and keyboard with USB connected ones.

Try running that way and see what happens.

Also, run dm_log_collector again and upload the zip file. Want to see the latest e3vent log entries.

redlum · 11 Jun 2017

Hi ztrucker.

Currently I only have a usb mouse (Razer) and keyboard (Dell) connected.

Prior to replacing the PSU a couple of days ago I had an external dvd drive and a Microsoft Wireless Controller (for official xbox gamepad).

I also had a USB wifi adaptor/dongle attached but replaced that with a Asus PCI-E card when I swapped the PSU.

Full log collector below for the past two crashes:
Attachment 139062

Many thanks
George

Ztruker · 12 Jun 2017

Looking through the event log I see 30 of these:

Code:

Event[7440]:
  Log Name: System
  Source: Microsoft-Windows-Kernel-Boot
  Date: 2017-06-11T21:20:55.679
  Event ID: 29
  Task: N/A
  Level: Error
  Opcode: Info
  Keyword: N/A
  User: S-1-5-18
  User Name: NT AUTHORITY\SYSTEM
  Computer: DESKTOP-L224S2J
  Description: 
Windows failed fast startup with error status 0xC00000D4.

Disable Fast Startup, see if that helps: How to Turn On or Off Fast Startup in Windows 10

redlum · 16 Jun 2017

Hi Rich

I disabled fast startup but still received another IRQL NOT LESS OR EQUAL .

I've attached a new report, in case there's something else in this one.

Attachment 139749

Many thanks
George

Ztruker · 16 Jun 2017

Latest dump shows:

Code:

BugCheck A, {8, 2, 1, fffff80145a2db2c}
Probably caused by : raspptp.sys ( raspptp!CtlDisconnectCallback+a7 )

Driver Description: Peer-to-Peer Tunneling Protocol (Microsoft)

Networking definitely involved. Any way you can switch to Ethernet instead of WiFi for awhile for testing purposes? If doing so resolves the problem then we need to look for a newer driver for your Realtek RTL8192CU Wireless LAN 802.11n USB 2.0 Network adapter or replace it.Adapter

redlum · 21 Jun 2017

Hi Rich

The Realtek RTL8192CU Wireless LAN 802.11n USB 2.0 Network Adaptor was replaced prior to the last couple of crashes. I've been running an ASUS PCI-Express WIFI card for a week or two now.

I did go through and delete all the old Realtek USB wifi drivers from the system but this evening I've had another memory_management crash. I've attached the logs, hopefully this one has something interesting!

Attachment 140534

Many thanks
George

Ztruker · 21 Jun 2017

The latest dump shows a problem with dxgmms2.sys.

Code:

BugCheck 1A, {41793, ffffe300f8bdcfd8, 1fc, 1fb}
*** ERROR: Symbol file could not be found.  Defaulted to export symbols for dxgmms2.sys - 
Probably caused by : dxgmms2.sys ( dxgmms2!VidMmInterface+3c6eb )

Driver Description: DirectX Graphics MMS

So this is definitely graphics related. I check the driver for your NVIDIA GeForce GTX 950 and it's a bit downlevel:
Version 382.05 dated 1 May 2017. There is a newer version available:
GeForce Game Ready Driver

Version:	382.53 ^WHQL
Release Date:	2017.6.9
Operating System:	Windows 10 64-bit
Language:	English (US)
File Size:	423.35 MB

Remove and install latest Nvidia drivers:

I suggest completely uninstalling the Nvidia display drivers using Display Driver Uninstaller (DDU) from WagnardMobile (near bottom of page) then get the latest driver for you Nvidia card here: NVIDIA Driver Downloads

Then do a custom install of only the NVidia graphics driver and the PhysX driver.

See if that gets rid of the problem.

zbook · 21 Jun 2017

If the NVidia does not completely fix the bsod check to see if you are using anything by Wacom.
WTouch User Mode Driver
Please uninstall and reinstall the software/driver for anything Wacom
Can you use a wired connection as above and not use a router while troubleshooting?
WacomPen Wacom Serial Pen HID D Wacom Serial Pen HID D Kernel Manual C:\WINDOWS\system32\drivers\wacompen.sys
wacomrouterf Wacom Router Filter Dr Wacom Router Filter Dr Kernel C:\WINDOWS\system32\drivers\wacomrouterfilter.sys

Are you using Adobe photoshop? lightroom.exe
Can you uninstall and reinstall the software?

Are you using any Garmin products? esu.exe
Can you uninstall and reinstall them?

zbook · 21 Jun 2017

Code:

A corruption was discovered in the file system structure on volume WD.
A corruption was found in a file system index structure.  The file reference number is 0x5000000000005.  The name of the file is "\".  The corrupted index attribute is ":$I30:$INDEX_ALLOCATION"

Code:

A corruption was discovered in the file system structure on volume WD.
A corruption was found in a file system index structure.  The file reference number is 0x5000000000005.  The name of the file is "\".  The corrupted index attribute is ":$I30:$INDEX_ALLOCATION".

Code:

A corruption was discovered in the file system structure on volume F:.
A corruption was found in a file system index structure.  The file reference number is 0x3000000000fc1.  The name of the file is "\STEAM\steamapps\common\Counter-Strike Global Offensive\csgo\resource\flash\econ\weapons\cached".  The corrupted index attribute is ":$I30:$INDEX_ALLOCATION".

Code:

A corruption was discovered in the file system structure on volume WD.
A corruption was found in a file system index structure.  The file reference number is 0x5000000000005.  The name of the file is "\".  The corrupted index attribute is ":$I30:$INDEX_ALLOCATION".

Code:

A corruption was discovered in the file system structure on volume D:.
A file system index structure contains entries that violate ordering rules.  The file reference number is 0xa000000001cd9.  The name of the file is "\FLAC".  The corrupted index attribute is ":$I30:$INDEX_ALLOCATION".  The corrupted subtree is rooted at entry number 0 of the index block located at Vcn 0x5.

[CODE][A corruption was discovered in the file system structure on volume D:.
The exact nature of the corruption is unknown. The file system structures need to be scanned online.
/CODE]

[CODE][Windows failed fast startup with error status 0xC00000D4./CODE]

[CODE][Crash dump initialization failed!/CODE]

Code:

The file system structure on volume F: cannot be corrected.
Please run the chkdsk utility on the volume F:.

Code:

The file system structure on volume D: cannot be corrected.
Please run the chkdsk utility on the volume D:.

Open administrative command prompt and type or copy and paste:
1) winver (in the pop up about windows > view your windows version and build > type this information into the thread)
2) sfc /scannow
3) dism /online /cleanup-image /restorehealth
When these have completed > right click on the top bar or title bar of the administrative command prompt box > left click on edit then select all > right click on the top bar again > left click on copy > paste into the thread

On each drive please run one of these SMART tests and post images for each drive into the thread:
http://crystalmark.info/software/Cry...o/index-e.html
http://www.hdtune.com/
https://www.hdsentinel.com/

Please plan to open administrative command prompt and type or copy and paste:
chkdsk /x /f /r
Please run chkdsk in this format for all of your drives. It may take a long time to run so plan to run overnight.