Only able to boot in safe mode; constant blue screens/restarting

The log is attached, and the thread title basically explains the issue. The only way I've been able to start my computer this morning (after some system hangs and general wonkiness last night) without blue screens is via safe mode (luckily with networking). I've tried system restore, resetting the computer, but neither has worked. (Haven't been able to get any motherboard BIOS functions to work either on startup.)

I believe the culprit may be (at least in part) the Razer Synapse driver--people on this forum have advised me that it can cause problems, but I'm unable to uninstall it. I get this error message: "The Windws Installer Service could not be accessed. This can occur if the Windows Installer is not correctly installed. Contact your support personnel for assistance." Any help would be appreciated! Thanks.

All dumpfiles blames

Code:

BugCheck 133, {1, 1e00, 0, 0}

*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
*** WARNING: Unable to verify timestamp for win32k.sys
*** ERROR: Module load completed but symbols could not be loaded for win32k.sys
Probably caused by : memory_corruption

Followup: memory_corruption

This is the driver of your nvdia geforce card.
The driver might be corrupted uninstall with DDU download ddu and reinstall.

...

Lifetec,

The good news is that I was able to boot up normally after deleting the driver. The new problem is that whenever I try to install the latest graphics card driver, the computer spontaneously does a series of long, mysterious restarts (without any dialog prompt or warning) and then booted back up with low resolution indicating the card driver wasn't installed. I installed an earlier version of the graphics card, and it was stable for a little bit until it blue screened again. I have attached the latest crash dump information.

Both of the 2 latest dumpfiles are:

Code:

  .....................
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 119, {1, 5f2, 5f5, ffffda079b24e180}

*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
Probably caused by : dxgmms2.sys ( dxgmms2!VidSchiVerifyDriverReportedFenceId+d757 )

Followup: MachineOwner
---------

0: kd> !analyze -v
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

VIDEO_SCHEDULER_INTERNAL_ERROR (119)
The video scheduler has detected that fatal violation has occurred. This resulted
in a condition that video scheduler can no longer progress. Any other values after
parameter 1 must be individually examined according to the subtype.
Arguments:
Arg1: 0000000000000001, The driver has reported an invalid fence ID.
Arg2: 00000000000005f2
Arg3: 00000000000005f5
Arg4: ffffda079b24e180

This is a very common BSOD, when googling this you get many hits, but no real solution.
Mostly they say it is driver related, corruption or driverfaults.
Sometimes there are mentions of faullty hardware(gpucard).

Possible solution.
Try installing a older nvdiadriver (you have now the 17 november) use DDU
Do you have a other GPU card(or borrow one) to test if your system with the other GPUcard does not BSOD. ( then probably your current one is faulty)
Or test your GPUcard
Videotest Furmark
To test your GPU you can use Furmark see this tutorial FurMark - GPU Stress Test - Windows 10 Forums
FurMark download site: FurMark: VGA Stress Test, Graphics Card and GPU Stability Test, Burn-in Test, OpenGL Benchmark and GPU Temperature | oZone3D.Net
FurMark Setup:
- If you have more than one GPU, select Multi-GPU during setup
- In the Run mode box, select "Stability Test" and "Log GPU Temperature"
Click "Go" to start the test (Looks like it's "BURN-IN test" now)
- Run the test until the GPU temperature maxes out - or until you start having problems (whichever comes first).
NOTE: Set the alarm to go off at 90ºC. Then watch the system from that point on. If the system doesn't display a temperature, watch it constantly and turn it off at the first sign of video problems. DO NOT leave it it unmonitored, it can DAMAGE your video card!!!
If the temperature gets above 100ºC, quit the test - the video card is overheating.
- Click "Quit" to exit

What you are looking for:
- excessive heat from the GPU (report back with anything over 90ºC)
- problems with the video display (picture is distorted or jumbled, picture turns black, etc)
- problems reported by the program (I haven't seen this, but "just in case")

Do you have Daemon tools installed, this program is known for BSOD on some systems.
Uninstall it and see if this helps to stabileze your system.

Look on the supportpage of your mobo and update all your drivers to the latest versions(if avaliable) to get your system as stable as can be.

I'm afraid I do not have access to another graphics card. Also, the system appears to have become so unstable that now I can't install any graphics card drivers. I tried an older one like you suggested (the one before 11/17/16), but system crashed as it was installing the driver. I had to restart in safe mode (via the eventual Windows prompt when your system crashes/restarts too many times). I tried to install drivers two more times, and the same thing kept occurring (it would crash while installing the driver). I would like to try and flash a new BIOS, but I can't even access my BIOS options (pressing any of the function keys during the BIOS splash window crashes the system). I do not have Daemon Tools.

Will Furmark still work if my graphics card doesn't have a driver installed? (My understanding is that without a driver, the system relies on a bare necessity-card in the motherboard; without a driver installed, will it still be able to test the GPU?) It seems worth noting that my (relatively mediocre) graphics card is about 4.5 years old, and my internet research suggests that even high-end cards only last between 4-5 years with a max lifespan of seven years...

Edit: I'm more than happy to try anything; I just want to know whether I should spend my time attempting to keep going back and install older and older drivers or whether I should just run Furmark?

Your mobo has a new Bios version F16h from 2016/07/19 after almost 3 years. This might be a good idea.
Maybe for a better support of windows 10?, you could download the files and look for a read me etc. to check the changes.

Maybe it is a idea to (temporary) remove your geforce card.
And use your onboard graphics to see how stable your system is at the moment after all those crashes and bsod.
And to see if you can now acces your BIOS and to check all your settings and/or reset them to default.
Then reinstall your geforce and try to install the drivers.
It this still is not possible than you could eventually deceide to update your BIOS to the latest version.

Could consider a reset of windows 10. ?