BSOD System Service Exception

Hello All,

I must say, I am at my wits end and am really hoping that the wonderful folks here at TenForums are able to help.

My computer frequently, yet seemingly random, BSODs. The error it throws on the Blue Screen is "System Service Exception" with no numbers, or anything other than that.

I have attempted a number of things to resolve, but as of yet, no success. Ive run MemTest86+ a few times at boot, all good there. I disabled or uninstalled a some drivers, applications, services etc that I thought may be causing the problem, but no success there either.

Anyway, I really like this computer when its working and would really hate to have to get a new one and I am hoping that the collective genius here at TenForum can pinpoint the problem so I wont have to replace everything. Thanks in advance for any assistance.

I have attached my recent log as per the forum instructions, and additionally added my system info for reference.

Thank you!

Attachment 110501Attachment 110502

While waiting for a response, I went ahead and reinstalled the OS (clean) and then updated my drivers. And, shortly after my pc starting BSODing again This time it threw the WHEA Uncorrectable error, immediately followed by a KMODE Exception Not handled. After that, I booted to recovery cmd prompt and ran SFC Scannow. About 5 minutes into that it BSOD'ed with CACHE_Manager error. Ugh...

Here are most recent logs:
Attachment 110535

Round 3: Attachment 110800

When you reply to your own thread, it looks to us like someone is already working with you so we move on to the next BSOD that has no responses.

Looked at the latest dump and see this:

Code:

BugCheck D3, {fffff80001c9b01d, 2, 0, fffff803313150f6}
*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
Probably caused by : memory_corruption

You currently have the 375.86 version, the web site had:

Code:

Version: 375.95
Date: 2016.11.18

Also, because of the possible memory corruption, it would be good to run memtest86+ as follows:
===================================================
Follow this tutorial: MemTest86+ - Test RAM - Windows 10 Forums

MemTest86+ is a diagnostic tool designed to test Random Access Memory (RAM) for faults. MemTest86+ will verify that:

• RAM will accept and keep random patterns of data sent to it
• There are no errors when different parts of memory try to interact
• There are no conflicts between memory addresses

Memtest86+ runs from bootable media to isolate the RAM from the system, no other components are taken into account during the test.

   Warning

MemTest86+ needs to run for at least 8 passes to be anywhere near conclusive, anything less will not give a complete analysis of the RAM.

If you are asked to run MemTest86+ by a Ten Forums member make sure you run the full 8 passes for conclusive results. If you run less than 8 passes you will be asked to run it again.

   Note

MemTest86+ has been known to discover errors in RAM in later passes than the eighth pass. This is for information only; if you feel there is a definite problem with the RAM and 8 passes have shown no errors feel free to continue for longer.

Running 8 passes of MemTest86+ is a long and drawn out exercise and the more RAM you have the longer it will take. It's recommended to run MemTest86+ just before you go to bed and leave it overnight.

I don't know what that means nor can I find any useful info on it.
For additional testing, remove all but 1 DIMM and out it in slot 2 then run memtest86+ and see if it fails. If no, swap in another DIMM and tes. Repeat until the defective one is found.

If no help, I see you have 24GB of ram. Looking at the manual that is not a supported configuration (2 slots of 4 filled).
I suggest running with 16GB (8GB in two slots) in slots 2 and 4 per the manual, see if that helps.

Attachment 110922

Great, hope that's the end of it.