BSOD After Windows 10 Install

  1. Posts : 3
    Windows 10 Home 64-bit (10.0, Build 14393)
       08 Jul 2016 #1

    BSOD After Windows 10 Install

    Hello... I recently did a clean install of Windows 10.

    I've gotten a couple of BSOD occurrences.

    The most recent was a IRQL_NOT_LESS_OR_EQUAL. The previous one was different, but I don't recall the error message.

    Please let me know what you think.

    Thank you...
      My ComputerSystem Spec

  2. Ztruker's Avatar
    Posts : 6,614
    Windows 10 Pro X64 1809 17763.134
       08 Jul 2016 #2

    The dump indicates memory_corruption which may be defective RAM or a driver passing bad data.

    You have a ATI Radeon HD 3450 whos driver is dated 1/13/2015 12:00:00 AM. There is no Windows 10 driver for this card.

    The following is a list of graphics products that do not support Windows® 10:
    • ATI Radeon™ HD 4000 Series /ATI Mobility Radeon™ HD 4000 Series Graphics
    • ATI Radeon™ HD 3000 Series /ATI Mobility Radeon™ HD 3000 Series Graphics
    • ATI Radeon™ HD 2000 Series /ATI Mobility Radeon™ HD 2000 Series Graphics
    • ATI Radeon™ X1### Series/ATI Mobility Radeon™ X1### Series Graphics
    • ATI Radeon™ X### Series/ATI Mobility Radeon™ X### Series Graphics
    • ATI Radeon™ 9000 Series Graphics
    • ATI Radeon™ 8500 Graphics
    • ATI Radeon™ 7500 Graphics
    • ATI Radeon™ DDR Graphics
    • ATI Radeon™ 7000 Graphics
    • ATI Radeon™ 7000VE Graphics
    • ATI Radeon™ 7000LE Graphics

    Try testing your RAM, see if that is the problem:


    Follow this tutorial: MemTest86+ - Test RAM - Windows 10 Forums


    is a diagnostic tool designed to test Random Access Memory (RAM) for faults. MemTest86+ will verify that:

    • RAM will accept and keep random patterns of data sent to it
    • There are no errors when different parts of memory try to interact
    • There are no conflicts between memory addresses

    Memtest86+ runs from bootable media to isolate the RAM from the system, no other components are taken into account during the test.

    MemTest86+ needs to run for at least 8 passes to be anywhere near conclusive, anything less will not give a complete analysis of the RAM.

    If you are asked to run MemTest86+ by a Ten Forums member make sure you run the full 8 passes for conclusive results. If you run less than 8 passes you will be asked to run it again.

    MemTest86+ has been known to discover errors in RAM in later passes than the eighth pass. This is for information only; if you feel there is a definite problem with the RAM and 8 passes have shown no errors feel free to continue for longer.

    Running 8 passes of MemTest86+ is a long and drawn out exercise and the more RAM you have the longer it will take. It's recommended to run MemTest86+ just before you go to bed and leave it overnight.
      My ComputersSystem Spec

  3. Posts : 3
    Windows 10 Home 64-bit (10.0, Build 14393)
    Thread Starter
       10 Jul 2016 #3


    Thanks Rich...

    Here's a photo of the findings.
      My ComputerSystem Spec

  4. Ztruker's Avatar
    Posts : 6,614
    Windows 10 Pro X64 1809 17763.134
       10 Jul 2016 #4

    Well, that's definitely a defetive memory module (DIMM) for sure.

    See the Results & Extended Testing section of the tutorial for info on how to determine what is defective.
    I would remove half the memory then run memtest86+ again. If it fails the DIMM that is still installed is defective. If not, swap the memory and run again.
      My ComputersSystem Spec


Related Threads
Solved Brand new clean windows 10 install - BSOD in BSOD Crashes and Debugging
I have run the tool and am attaching the file per the instructions. My computer is brand new and crashed while I was not even at my desk. I had nothing really "active" running. Hoping you guys can help me pinpoint what driver might be causing...
BSOD random with new windows 10 install. in BSOD Crashes and Debugging
Random different error code BSOD's cant figure out the problem. Windows 10 newly installed on new mobo cpu and RAM. Please help!!! See attachment Thanks!
Windows 10 Pro Random BSOD on new install in BSOD Crashes and Debugging
Hello everyone, I just put together a build with the following components Windows version: Windows 10 Pro , 10.0, build: 10240 Hardware: ASRock, Z77 Extreme4 CPU: GenuineIntel Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz Intel586, level: 6 SSD: M4...
BSOD after Windows update can't install in BSOD Crashes and Debugging
I am on the Windows 10 insider program. Currently on build number 10547. I started noticing an error in Update Windows that said that an update couldn't be installed (see the attached screenshot below) I have attempted to click install now. One of...
Solved BSOD on new Windows 10 install, Homebuild in BSOD Crashes and Debugging
I've installed Windows 10 on a new homebuild and am experiencing BSODs erratically, about seven times in the past two weeks. Most of the time they occur when the computer is idling and I'm away. Sometimes the computer is fine for a few days, other...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 07:08.
Find Us