Windows 10: 37 Crashes from Wide Range of Error Codes (0x0d1, 0x00a, 0x0109)

Page 1 of 4 123 ... LastLast

  1. Posts : 21
    Windows 10 Professional
       26 Jun 2016 #1

    37 Crashes from Wide Range of Error Codes (0x0d1, 0x00a, 0x0109)

    Hello, and as the title states, I have (from what Log Collector has said) 37 crashes. Ranging from 0x0d1, 0x0109, 0x00a, and possibly others. First off, some of the crashes were because my network adapter did not support Windows 10. Upon investigation, I determined that there WERE no drivers for it, so I bought a new one that natively supported Windows 10. I had hoped that that would fix the issue, but it did not.

    Crashes occur when: the computer is idle, when I am watching Youtube on Chrome, doing anything on Chrome, and sometimes I am fully unaware of what happened.

    Any help would be appreciated, and thank you for reading
      My ComputerSystem Spec

  2. Posts : 5,848
    Windows 10 Pro X64 16299.192
       26 Jun 2016 #2

    Looks like you may have a hardware and a driver problem. Dump indicates rtwlanu.sys is aproblemm. It's part of Realtek WLAN Wireless USB 2.0 Adapter. Need to find a newer driver for this device.

    Dump also indicates memory_corruptuion, a single bit failure.

    MODULE_NAME: memory_corruption
    IMAGE_NAME:  memory_corruption
    FOLLOWUP_NAME:  memory_corruption

    Follow this tutorial: MemTest86+ - Test RAM - Windows 10 Forums


    is a diagnostic tool designed to test Random Access Memory (RAM) for faults. MemTest86+ will verify that:

    • RAM will accept and keep random patterns of data sent to it
    • There are no errors when different parts of memory try to interact
    • There are no conflicts between memory addresses

    Memtest86+ runs from bootable media to isolate the RAM from the system, no other components are taken into account during the test.

    MemTest86+ needs to run for at least 8 passes to be anywhere near conclusive, anything less will not give a complete analysis of the RAM.

    If you are asked to run MemTest86+ by a Ten Forums member make sure you run the full 8 passes for conclusive results. If you run less than 8 passes you will be asked to run it again.

    MemTest86+ has been known to discover errors in RAM in later passes than the eighth pass. This is for information only; if you feel there is a definite problem with the RAM and 8 passes have shown no errors feel free to continue for longer.

    Running 8 passes of MemTest86+ is a long and drawn out exercise and the more RAM you have the longer it will take. It's recommended to run MemTest86+ just before you go to bed and leave it overnight.
      My ComputersSystem Spec

  3. Posts : 21
    Windows 10 Professional
    Thread Starter
       27 Jun 2016 #3

    This...isn't going well. Finished 2 passes, on 17% of the third, and I am on hour 10! Question: If it crashes while doing this, that means, for sure, hardware failure, right? Because this might take over 35 hours
      My ComputerSystem Spec

  4. Posts : 5,848
    Windows 10 Pro X64 16299.192
       27 Jun 2016 #4

    An alternative way to test ram is to remove half then test. You have 16GB so that would leave you with 8GB which should be plenty.
    Run that way for a day and if no errors, hangs or BSODs then swap removed and installed ram and test for another day.

    If you have problems with one DIMM (memory module) and not the other, replace the failing one with one identical to what you keep.

    What about the Realtek Wireless device? I don't see any mention of a onboard wireless so it must be an addon card or a USB dongle. Need to update it's driver.
      My ComputersSystem Spec

  5. Posts : 21
    Windows 10 Professional
    Thread Starter
       27 Jun 2016 #5

    It's a USB dongle. I found an update for it, and I either installed it, or just downloaded it. It was getting late, so I started running memtest. I didn't realize it was going to be this slow
      My ComputerSystem Spec

  6. Posts : 5,848
    Windows 10 Pro X64 16299.192
       27 Jun 2016 #6

    Ok, hopefully that will esolve the WiFi problem.

    Are you still running Memtest86+?
      My ComputersSystem Spec

  7. Posts : 21
    Windows 10 Professional
    Thread Starter
       28 Jun 2016 #7

    All right, first slot and first stick are clear of issues. Later today I will test the second stick. If that turns up clear, it isn't a slot or a stick issue.
      My ComputerSystem Spec

  8. Posts : 21
    Windows 10 Professional
    Thread Starter
       28 Jun 2016 #8

    I have a question. Should my RAM be running faster than 369 MHz? Or is that an error on Memtest's part?
      My ComputerSystem Spec

  9. Posts : 5,848
    Windows 10 Pro X64 16299.192
       28 Jun 2016 #9

    Can you post a picture of what you are talking about? A digital camera pic would be okay.
      My ComputersSystem Spec

  10. Posts : 21
    Windows 10 Professional
    Thread Starter
       29 Jun 2016 #10

    Sure thingAttachment 87359 Also, as you can see, no crashes, no errors, and as such, it looks like both slots on my motherboard, and both RAM sticks are okay. Unless the speed is an issue
      My ComputerSystem Spec

Page 1 of 4 123 ... LastLast

Related Threads
Solved Infinite BSOD Loop, Various Error Codes in BSOD Crashes and Debugging
I did a teardown of my Windows 10 machine to clean all the parts and do some cable management and when I reassembled and restarted I had some issues. It started with a corrupted RAM BSOD, so I cleaned the connector pins on the RAM sticks with...
FYI - The list of error codes for Windows 10 setup Read more:
Hopefully this is the correct subforum to post this in. If it is not could somebody point me to the correct one? I am using THIS guide here on tenforums. When I try to dump the stack I input the command dps ffffd00026876000...
A couple of BSODs, different error-codes in BSOD Crashes and Debugging
Hi TenForums I updated my 8.1 Pro laptop to 10 Pro a couple of weeks ago, and so far I really like what I see. The only nasty bit about W10 so far has been these BSODs happening every once in a while. After the first few I decided I might need...
Multiple BSOD error codes in BSOD Crashes and Debugging
I updated from windows 7 the day that 10 launched and for a few days everything worked perfectly, then I crashed a few times, and today I crashed three times, all for different reasons. The first crash was a kernell_data_inpage_error. I did...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 04:53.
Find Us