Tablet has bluescreens during night/standby

Page 2 of 3 FirstFirst 123 LastLast

  1. Posts : 14,901
    Windows 10 Pro
       #11

    It doesn't 100% verify what I think happens, I thought that the BSOD happened at the beginning or the end, but as there is no driver flagged in the dump we'll need to run driver verifier. Most other usual causes are ruled out so that is a good sign :)
    Please follow below instructions.




    Diagnostic Test

     DRIVER VERIFIER


    warning   Warning
    Please make a backup of your important files and get your rescue media or create one.
    Please create a restore point.

    Please follow this tutorial to run driver verifier.

    Some windows drivers are blamed in a few crashes, but that usually means that a 3rd party driver is actually the cause.
    Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.

    Driver verifier should be performed for a max of 48 hours, or when you have a bluescreen, whatever comes first.

    If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.

    Note   Note
    Your system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.


    Usual causes:
    • Memory corruption,
    • Hardware (memory in particular),
    • Overclocking failure,
    • Installing a faulty or mismatched hardware (especially memory) or a failure after installing it,
    • 3rd party firewall,
    • Device drivers,
    • SCSI/network/BIOS updates needed,
    • Improperly seated cards,
    • Incompatible storage devices,
    • Overclocking,
    • Virus scanner,
    • Backup tool,
    • Bad motherboard,
    • Missing Service Pack
      My Computers


  2. Posts : 64
    Windows 10
    Thread Starter
       #12

    I have activated it, rebooted and now Windows doenst start anymore there is bluescreen at Windows start...
      My Computer


  3. Posts : 14,901
    Windows 10 Pro
       #13

    Partly that is a good sign, have you tried my suggestions for getting back in Windows like driver verifier reset, safe mode or a restore point?
      My Computers


  4. Posts : 64
    Windows 10
    Thread Starter
       #14

    I cant get into windows because it automatically runs into bluescreen, it did that for 2 or 3 times, then "automatic repair" was started, I selected "repair last" or something, there was nothing else to select anyway (I created a manual repair point before turning on the tool), now it's frozen and doesn't do anything anymore since 5 minutes...
      My Computer


  5. Posts : 14,901
    Windows 10 Pro
       #15

    After 3 times boot failure you should get the troubleshooting options, go into the advanced troubleshooting options and in there choose command prompt, then enter the command
    Code:
    verifier /reset
      My Computers


  6. Posts : 64
    Windows 10
    Thread Starter
       #16

    Ok Im back in Windows, repair took a bit longer than expected, working again, seems it used the last repair point. Now what? And no, the automatic repair didn't give me any advanced options, just reboot and "repair last".
      My Computer


  7. Posts : 14,901
    Windows 10 Pro
       #17

    Please run the DM Log Collector again, with the BSODs dumps should have been created which we need to analyze to find out what driver caused it.
      My Computers


  8. Posts : 14,901
    Windows 10 Pro
       #18

    muffle said:
    Ok Im back in Windows, repair took a bit longer than expected, working again, seems it used the last repair point. Now what? And no, the automatic repair didn't give me any advanced options, just reboot and "repair last".
    No problem, I'm just glad you're back in Windows already :)
      My Computers


  9. Posts : 64
    Windows 10
    Thread Starter
       #19

    done.
      My Computer


  10. Posts : 14,901
    Windows 10 Pro
       #20

    Please update/reinstall Unified Remote 3.
    Code:
    1: kd> lmvm uvhid
    Browse full module list
    start    end        module name
    8e2b0000 8e2b9000   uvhid    T (no symbols)           
        Loaded symbol image file: uvhid.sys
        Image path: \SystemRoot\System32\drivers\uvhid.sys
        Image name: uvhid.sys
        Browse all global symbols  functions  data
        Timestamp:        Tue Mar 22 10:42:48 2016 (56F11398)
        CheckSum:         0001557A
        ImageSize:        00009000
        Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4
      My Computers


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 17:50.
Find Us




Windows 10 Forums