Page 1 of 4 123 ... LastLast

  1. Joined : Sep 2015
    Posts : 16
    Windows 10 x64
       06 Sep 2015 #1

    Multiple daily BSOD since Upgrade to Win10


    Hi, I am losing my mind and have run out of places to check for help, so hoping someone here can assist:

    I installed Win 10 on 8/8. Since then receiving the same 2 BSOD multiple times every day, but no indication as to the cause.

    I have updated every driver I can think of, when that didn't work, I clean reinstalled 3 different times.

    I have run SFC - it cannot correct errors found, then DISM /online retorehealth and it cannot find source run. Installed whocrashed, but it only points to ntoskrnl, and cannot find the specific issue.

    Anyhow, I am receiving these two errors which are logged in multiple mini-dmp files in the upload:
    DPC_WATCHDOG_VIOLATION
    POOL_CORRUPTION_IN_FILE_AREA

    Please help if you can!
    Thank you,
    Jason
      My System SpecsSystem Spec


  2. Joined : Jun 2015
    Posts : 10,898
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       06 Sep 2015 #2

    Hi flibbittygibbit,

    Welcome to the 10forums.

    Please make a screenshot of the error you get when running dism /online /cleanup-image /restorehealth and post it.

    Because the crashes are pointing to windows drivers/files, we need to find out if there are 3rd party drivers involved




    Multiple daily BSOD since Upgrade to Win10 Diagnostic Test Multiple daily BSOD since Upgrade to Win10
     DRIVER VERIFIER

    warning   Warning
    Please make a backup of your important files and get your rescue media or create one.
    Please create a restore point.

    Please read and run driver verifier.

    Some windows drivers are blamed in a few crashes, but that usually means that a 3rd party driver is actually the cause.
    Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.

    Driver verifier should be performed for a max of 48 hours, or when you have a bluescreen, whatever comes first.

    If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.

    Note   Note
    Your system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.
      My System SpecsSystem Spec


  3. Joined : Sep 2015
    Posts : 16
    Windows 10 x64
       06 Sep 2015 #3

    DISM screenshot


    Hi axe0,
    Thanks for the response! Here is the DISM screenshot. It will take me a bit to figure out this driver verifier thing though. I'll post that as soon as I can.
    Jason
      My System SpecsSystem Spec


  4. Joined : Jun 2015
    Posts : 10,898
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       06 Sep 2015 #4

    That error is a known problem with windows 10
    Try an in-place upgrade, it should solve the issue.
      My System SpecsSystem Spec


  5. Joined : Oct 2013
    Tropic of Cancer
    Posts : 1,648
    Microsoft Windows 10 Home
       06 Sep 2015 #5

    +
    Code:
    Windows failed fast startup with error status 0xC0000001.
    Error status 0xC0000001 means ....

    STATUS_UNSUCCESSFUL: {Operation Failed} The requested operation was unsuccessful.


    IMHO you should disable fast startup, which will at least stop the disk check on all the drives during boot.

      My System SpecsSystem Spec


  6. Joined : Sep 2015
    Posts : 16
    Windows 10 x64
       06 Sep 2015 #6

    axe0 said: View Post
    That error is a known problem with windows 10
    Try an in-place upgrade, it should solve the issue.
    Hi axe0,
    I already did that 2x. Third time I used burned iso, b/c after 2x, I got INACCESSIBLE_BOOT_DEVICE upon 3rd reset b/c I was messing with MB Inter RAID vs AHCI settings.

    This is the fourth iteration of Win10 installation. Is repeating what I have already done, expecting a different outcome the way to go (definition of insanity, right?) and start again from scratch only to end up hours later exactly where I am at the moment? I hope this makes sense that I'd like to use that as a last resort. Driver Verifier is running for a while now. ill post again once something happens. Thanks again!
    Jason
      My System SpecsSystem Spec


  7. Joined : Sep 2015
    Posts : 16
    Windows 10 x64
       06 Sep 2015 #7

    Arc said: View Post
    +
    Code:
    Windows failed fast startup with error status 0xC0000001.
    Error status 0xC0000001 means ....

    STATUS_UNSUCCESSFUL: {Operation Failed} The requested operation was unsuccessful.


    IMHO you should disable fast startup, which will at least stop the disk check on all the drives during boot.
    Hi Arc,
    Thank you for the input. I was not away of that start-up goofiness, and normally turn hibernate off anyhow, but apparently skipped it this install. Hibernate is now off:
      My System SpecsSystem Spec


  8. Joined : Jun 2015
    Posts : 10,898
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       06 Sep 2015 #8

    flibbittygibbit said: View Post
    Hi axe0,
    I already did that 2x. Third time I used burned iso, b/c after 2x, I got INACCESSIBLE_BOOT_DEVICE upon 3rd reset b/c I was messing with MB Inter RAID vs AHCI settings.

    This is the fourth iteration of Win10 installation. Is repeating what I have already done, expecting a different outcome the way to go (definition of insanity, right?) and start again from scratch only to end up hours later exactly where I am at the moment? I hope this makes sense that I'd like to use that as a last resort. Driver Verifier is running for a while now. ill post again once something happens. Thanks again!
    Jason
    Isn't an option anymore then, next time please add everything you have done in the post
      My System SpecsSystem Spec


  9. Joined : Sep 2015
    Posts : 16
    Windows 10 x64
       06 Sep 2015 #9

    axe0 said: View Post
    Isn't an option anymore then, next time please add everything you have done in the post
    Sorry axe0,
    I thought I had when I stated in my original request that I clean reinstalled 3 different times. I'll be more specific in the future. Thanks again for your help!
    Jason
      My System SpecsSystem Spec


  10. Joined : Jun 2015
    Posts : 10,898
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       06 Sep 2015 #10

    flibbittygibbit said: View Post
    Sorry axe0,
    I thought I had when I stated in my original request that I clean reinstalled 3 different times. I'll be more specific in the future. Thanks again for your help!
    Jason
    Yes you have, but an in-place upgrade isn't the same as a clean install, refresh or reset (for so far I understand it)
      My System SpecsSystem Spec


 
Page 1 of 4 123 ... LastLast


Similar Threads
Thread Forum
Multiple BSOD codes in a week; after Win10 upgrade
Hi, I have recently upgraded from Win8 to Win10 (clean install, kept only the non-system data partition). While running Win8 it may have crashed once or twice in the past year, but nothing major. Since installing Win10 about a week ago, I've had...
BSOD Crashes and Debugging
win10 upgrade when owning multiple computers
I'd like to try 10 on one of my computers. If I sign up for it on one of my computers, does it automatically download to all my computers? Programs I use from GM are not supported for 10, so i need to keep all my laptops on 7. I'm willing to gamble...
Installation and Setup
Daily BSOD
Almost daily BSOD after upgrade from Win 8.1 to Win 10. This is a different laptop than my other posts in this forum. ASUS 12 GB - see details in screenshot. Thanks!34300
BSOD Crashes and Debugging
Random Multiple Daily BSOD 4 days after Win10 Install
Everything was running smooth. No issues, loving Win 10. Then, the first BSOD came 2 days ago followed by a random BSOD now every 1-3 hours. I have uninstalled many programs attempting to get to as clean of an install as possible but to uninstall...
BSOD Crashes and Debugging
BSOD after official win10 upgrade
So i finally got the msg that win 10 is ready for install, so i pressed installed after the first restart(during install) i got BSOD which was weird. So i went through the rest of the setup and finally windows booted and less than 5 min on use i...
BSOD Crashes and Debugging
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 17:26.
Find Us
Twitter Facebook Google+



Windows 10 Forums