Windows 10: multiple occurances of IRQL_NOT_LESS_OR_EQUAL Solved

Page 7 of 12 FirstFirst ... 56789 ... LastLast
  1.    06 Sep 2015 #61

    I went upstairs for lunch and came down and the system had crashed, again. The cpu temps were pretty low.
    DATE TIME MHz CPU_0 CPU_1 CPU_2 CPU_3 LOAD%
    09/06/15 12:16:00 1603.63 47 45 46 42 1.4
    I've got dumps if you want to look at them.
    Just as an experiment I'm going to shuffle my memory chips and then take another shot or two at memtest86+
    I'm attaching dm log if your interested.
      My ComputerSystem Spec


  2. Posts : 11,547
    Windows 10 Pro
       06 Sep 2015 #62

    Code:
    BugCheck A, {ffffa001e2c45e68, 2, 0, fffff802b7e386ca}
    
    Probably caused by : memory_corruption ( nt!MiIdentifyPfn+1ea )
      My ComputersSystem Spec

  3.    06 Sep 2015 #63

    Thanks axe0.
    I'm taking my system down now to play with simms.
      My ComputerSystem Spec

  4.    06 Sep 2015 #64

    I have 6 2 GB SIMM's. 3 Corsair's which I put in when I originally built the system in 2009. Then I added 3 Crucial this last december
    I swapped my SIMM's around, started to run memtest86+ and the screen went blank in less than five minutes
    I then removed my older Corsair's and ran memtest86+ for about 8 mins and blank screen. 2nd attempt about 3 mins before blank screen.
    Before I continue down this path of playing with memory configurations I'd like to l know what either of you can tell me about this memtest86+. I understand that it takes awhile to run 8 passes. over night I'm told.
    What should I expect with regards to the monitor staying on. Should it? if it does go off should I be able to wake it up?
    If it was a memory issue wouldn't the program just report errors as opposed to hanging, it that's what it's doing.
    instead could I be dealing with a different problem like motherboard?
    What is your experience with memory issues and running memtest86+
      My ComputerSystem Spec


  5. Posts : 8,216
    Windows 10 Enterprise and Pro/Windows 7 Enterprise/Linux Mint
       06 Sep 2015 #65

    The screen should stay on. You should never mix ram. Ram should be bought in kits. Try taking the new memory out and running just the old memory. Make sure the correct Frequency, timings and Dram voltage is set in bios. That information is on a sticker on the side of the ram sticks or on the package they came in.

    If it won't run with the 3 old sticks in, try running it with just 1 stick. Yes, it has to run a minimum of 8 passes to completely check the ram. Each pass tests something different and each pass consists of 10 tests. Each test checks something different.

    I guess it is possible that the monitor has a sleep setting on it. None of mine do, but in theory it is possible.
      My ComputersSystem Spec

  6.    06 Sep 2015 #66

    Dang, Sure enough. I read the P6T user guide and it said they recommend DIMM's from the same manufacture. The sales clerk at Micro Center said it was okay as long as they were in matched sets.
    I'll swap in the originals and try running the test.
      My ComputerSystem Spec


  7. Posts : 8,216
    Windows 10 Enterprise and Pro/Windows 7 Enterprise/Linux Mint
       06 Sep 2015 #67

    That rule applies to any board. Make sure the timings, frequency and Dram Voltage is set correctly in BIOS.
      My ComputersSystem Spec

  8.    06 Sep 2015 #68

    everything looks to be set to Auto. You are saying that I should set these manually instead of auto?
    I found the frequency
    There is qpi/dram core voltage and dram bus voltage. Not sure what the difference is and which to set.
    There is a DRAM Timing Control, and that section is really confusing. I haven't figured that out yet.

    Oh, And while I was in Bios and reading the user guide the screen went blank on me twice.
    I tired running memtest86+ on the three old with the same hang.
    I'm not sure I can go down to 1 DIMM. The spec says 2 DIMM is the smallest "recommended" configuration. It doesn't say if 1 DIMM is supported or not.
      My ComputerSystem Spec


  9. Posts : 8,216
    Windows 10 Enterprise and Pro/Windows 7 Enterprise/Linux Mint
       06 Sep 2015 #69

    Make sure you watch your GPU Temps closely and run Furmark GPU Stress test. FurMark - GPU Stress Test. The temps will go up very high and very fast. If they get too high, stop the test. Watch as the stop risisg and level out. It will only take a few minutes. But keep a close watch on the GPU Temps.
      My ComputersSystem Spec

  10.    06 Sep 2015 #70

    whats too high? 100c?
      My ComputerSystem Spec


 
Page 7 of 12 FirstFirst ... 56789 ... LastLast

Related Threads
Bsod irql_not_less_or_equal in BSOD Crashes and Debugging
Upgrade to Windows 10 yesterday, from Windows 7 Pro. After a couple of hours of usage, I started getting BSODs, more specifically IRQL_NOT_LESS_OR_EQUAL. I decided to reset the system, but the same problem keeps occurring. I'm thinking it's a...
Bsod:- irql_not_less_or_equal in BSOD Crashes and Debugging
BSOD occurs at shutdown:- IRQL NOT LESS OR EQUAL file path: C:\Windows\system32\drivers\clfs.sys
Bsod, irql_not_less_or_equal in BSOD Crashes and Debugging
I want to ask you for help to find the cause of bsod. Windows 10, random bsod after a few hours of use 35301
Irql_not_less_or_equal in BSOD Crashes and Debugging
heya i upgraded to windows 10 yesterday and now i keep getting a blue screen. IRQL_NOT_LESS_OR_EQUALI think this is because of a bad driver? any ideas on how i can fix this. I already reinstalled my graphic card drivers with no succes.:(
Solved BSOD - usbehci.sys - IRQL_NOT_LESS_OR_EQUAL in BSOD Crashes and Debugging
I have already had 7 of them, just got one when trying to post this. I suspect my USB sound card. So far they have happened only in Windows, not in games, when listening to the music on youtube or via Radiosure, sometimes I was not even at PC, so I...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 16:00.
Find Us