Windows 10: BSOD only after waking computer from sleep 0x000000be

Page 2 of 4 FirstFirst 1234 LastLast
  1.    02 Sep 2015 #11

    I went to the website and input my model number. It came back with no drivers. I will look again though.
      My ComputerSystem Spec

  2.    02 Sep 2015 #12

    I updated my answer on the ports in previous post. Don't know if you saw that or not. Searched again on Toshiba's website. There are no utilities or drivers available.
      My ComputerSystem Spec


  3. Posts : 8,157
    Windows 10 Enterprise and Pro/Windows 7 Enterprise/Linux Mint
       02 Sep 2015 #13

    Take a look at your manual. I believe ports 0 and 1 are sata III ports from the chipset. Ports 2,3,4,5 are Sata II ports, also from the Chipset. The Marvell Ports are designated as Gsata Ports 6,7,8. If you would swap your SSD and your DVD drive, I'm pretty sure you will get better performance from it. Sata III gives twice the performance of sata II, and the speed makes no difference to your DVD drive. But, look at your boot priorities in BIOS and be sure after changing ports it is the same.
    Last edited by essenbe; 02 Sep 2015 at 20:45.
      My ComputersSystem Spec

  4.    02 Sep 2015 #14

    Alright so I did some switching and now both hard drives are showing up on GSATA port 0 and 1 with the HDD on port 0 and the SSD on oort 1. But you were saying that having the ssd on the marvell controller might not be a good idea?
      My ComputerSystem Spec


  5. Posts : 8,157
    Windows 10 Enterprise and Pro/Windows 7 Enterprise/Linux Mint
       02 Sep 2015 #15

    Are You sure they are on Gsata ports 0 and 1. The specs for your board state that the Chipset ports are sata3 ports 0 and 1, and sata II ports 2,3,4,5,. The Marvell ports, which you don't want to use, are designated as Gsata ports 6,7,8. In the System Specs below, you want the SSD and hard drive on the #1 under Chipset. Ports 0 and 1, not on the Marvell ports, which are listed as Gsata ports 6,7,8.

    Attachment 35396
      My ComputersSystem Spec

  6.    02 Sep 2015 #16

    They are showing up in the marvell ATA controller config and not the ATA port information page. The DVD drive is in port 3 now though.

    Figured it out. It was plugged into the GSATA ports. It was a tight fit in there and I couldnt see the markings on the board that well.
      My ComputerSystem Spec


  7. Posts : 8,157
    Windows 10 Enterprise and Pro/Windows 7 Enterprise/Linux Mint
       02 Sep 2015 #17

    Yea, that's typical. They don't mark them for easy reading. Am I correct that you only have problems with sleep?
      My ComputersSystem Spec

  8.    02 Sep 2015 #18

    Yes I consistently have been able to recreate the stop message when I put the computer in sleep or it goes to sleep on its own and I try and wake it. At no other time have I had a stop message since installing 10. Some people had suggested turning off auto sleep mode and just putting it into hibernation instead. I have not tried this out yet.
      My ComputerSystem Spec


  9. Posts : 8,157
    Windows 10 Enterprise and Pro/Windows 7 Enterprise/Linux Mint
       02 Sep 2015 #19

    Hibernation may be turned off. It does that many time when it detects an SSD. We've seen a lot of people have problems with sleep. I don't use it, so I don't know.

    Try this. Right click the start button and select Command Prompt (Admin). copy/paste sfc /scannow and press enter. We want it to say no integrity violations were found. If it says files were found but couldn't be repaired, reboot and run it again. You may have to run it at lease 3 times with reboots in between each time.
      My ComputersSystem Spec

  10.    02 Sep 2015 #20

    It states that "Windows Resource Protection did not find any integrity violations."
      My ComputerSystem Spec


 
Page 2 of 4 FirstFirst 1234 LastLast

Related Threads
BSOD Error After Waking Up from Sleep in BSOD Crashes and Debugging
I put my PC to sleep and when I wake it up, I'm getting no display on my monitors although the PC itself wakes up. I reboot the computer and encounter a BSOD "VIDEO_TDR_FAILURE (nvlddmkm.sys)" I recently updated from Windows 7 to Windows 10. ...
BSOD sadface when waking up from sleep in BSOD Crashes and Debugging
I normally always sleep my PC, rarely shut it down. So I slept my PC like normal after updating to windows 10, and sadface BSOD came up. Tried it again, happened again. It keeps happening, 100% of the time I wake it up, BSOD. Not sure what is going...
Just to preface this I have not received a BSOD when this happens so I hope I'm still posting this in the correct location. However my laptop just freezes completely and I have to do a hard shutdown (holding the power button until it shuts off)...
Hello, since upgrading to Windows 10, my laptop has consistently crashed when waking up from sleep mode with the DPC Watchdog Violation given on the BSOD. This problem only began happening after the upgrade to Windows 10. So far I've attempted a...
Hello guys.... I just upgraded to Windows 10 and one problem that has been bugging me is that everytime I wake the computer from sleep it comes back up and then after a few seconds (like 3-4) I'm getting a BSOD with the message...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 12:37.
Find Us