New
#11
What did sfc /scannow say?
Please use the tool again and upload the zip file, I would need new information to prevent confusion with the software.
What did sfc /scannow say?
Please use the tool again and upload the zip file, I would need new information to prevent confusion with the software.
According to the information, you still have Daemon tools.
Please remove Daemon tools.
Please open taskmanager and msconfig:
- In taskmanager
- go to the tab startup
- disable everything
- In msconfig go to the tab services
- Check 'hide microsoft services'
- Uncheck all other services
- Click apply, click ok
- Reboot if asked
Does the problem still persist in a clean boot?
Also, please try driver verifier
WarningPlease make a backup of your important files and get your rescue media or create one.
Please create a restore point.
Please read and run driver verifier.
Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.
Driver verifier should be performed for a max of 48 hours, or when you have a bluescreen, whatever comes first.
If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.
NoteYour system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.
Funny, I've removed the daemon tools like you told me.According to the information, you still have Daemon tools.
Please remove Daemon tools.
Yes all the programs that start with windows were unchecked and I still had a bsodDoes the problem still persist in a clean boot?
I've used the verifier driver twice and had bsod before you even start the test.Please read and run driver verifier.
Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.
Driver verifier should be performed for a max of 48 hours, or when you have a bluescreen, whatever comes first.
If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.
bsod say: PAGE_FAULT_IN_NONPAGED_AREA is on file 082815-23703-01.dmp on 28/08 in zip.
(New bsod after clean boot)
My problem is that I can't analyse the dump files for some reason which i don't know.
So I'm forced to do some basic troubleshooting instead of specific troubleshooting, but right now it looks like the cause is your mainboard.
Please make sure your BIOS settings are set to default.
The only reason I can think of why there are problems with the dump files is hardware damage.
Please do the following tests againPlease Run Memtest86+
InformationPlease download from this site only http://www.memtest.org/ in the middle of the page are the Download links, you can download the ISO.zip or the Auto USB Flash Drive installer.zipExtract the Zip file. If you chose the ISO image, burn it to a CD using Windows Disk Image Burner or any Image burner you may have. If you downloaded the Auto USB installer, extract it, insert your USB 2.0 Flash Drive and take note of the drive letter. Run the installer, select the Flash Drive Letter, check the format box and press next. It will install memtest86+ to a flash drive. You can use either V4.20 or V5.01. Boot from your selected media. If you use V5.01 it will tell you to press certain buttons at the start, please press no buttons. The test will begin on it's own and continue to run until you stop it. It needs to run for 8 complete passes or until you receive an error. If you receive an error, stop the test. Even 1 error is a fail. Each pass tests a different part of the ram and each of the 10 tests in each pass tests something different. It takes a minimum of 8 passes in the same session to completely test the ram, more passes are better. It is quite a long test and will take several hours depending on how much ram you have. Due to the time length it is best to run overnight. If you have any questions, please do not hesitate to ask.
If these tests come again with a good result and your hard drive is also fine, then it is most likely the mainboard.
Please run Prime95 to test your CPU: Prime95 tutorial
NoteIf you're overclocking anything, please stop it and set everything back to default while troubleshooting
WarningYour CPU temperature will rise quickly while under this test. Keep a keen eye on the temperatures and abort the test if the temperatures rise too high
Please read this tutorial for testing your GPU
Please try a clean install of windows 10, backup important and personal files first.
A clean install may solve the problem if it is software related.
If all the hardware tests don't determine the cause and a clean install doesn't solve the problem, then it is for sure the mainboard.