Page 2 of 3 FirstFirst 123 LastLast

  1. Joined : Jun 2015
    Posts : 1,604
    Windows 3.1 to Windows 10
       25 Aug 2015 #11
      My System SpecsSystem Spec


  2. Joined : Jun 2015
    Posts : 10,897
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       25 Aug 2015 #12

    I have asked Kyhi about false positives with sfc /scannow in windows 10, because there are false positives in windows 8 and I'm unsure if the same files are false positive in windows 10.

    The link he posted points to a tool he wrote that helps with the sfc and dism commands.
      My System SpecsSystem Spec


  3. Joined : Aug 2015
    Posts : 42
    Windows 10 Pro 64bit
       26 Aug 2015 #13

    I have run the memtest for about 14 hours with the default settings, and there appears to be no errors.

    Attachment 33904

    On the other hand, sfc /scannow still cannot fix all the errors, even though I restarted at least 5 times, and some of them in safe mode too.

    If DISM is meant to be replacing files from a system image, maybe I should just reinstall Win7Pro and then try to upgrade from there?
      My System SpecsSystem Spec


  4. Joined : Jun 2015
    Posts : 10,897
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       26 Aug 2015 #14

    DISM is meant to fix problems when sfc can't.
      My System SpecsSystem Spec


  5. Joined : Aug 2015
    Posts : 42
    Windows 10 Pro 64bit
       26 Aug 2015 #15

    DISM in windows 7 can only scanhealth, not restorehealth..

    Attachment 33926

    I had another go at upgrading to Windows 10 from my current system in case something was fixed somewhere, but no.. the same BSOD and error code again....

    Any other ideas?
      My System SpecsSystem Spec


  6. Joined : Jun 2015
    Posts : 10,897
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       26 Aug 2015 #16

    Check for any drivers that could cause trouble:



    BSOD upgrading to Win10, error PAGE_FAULT_IN_NONPAGED_AREA Diagnostic Test BSOD upgrading to Win10, error PAGE_FAULT_IN_NONPAGED_AREA
     DRIVER VERIFIER

    warning   Warning
    Please make a backup of your important files and get your rescue media or create one.
    Please create a restore point.

    Please read and run driver verifier.

    Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.

    If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.

    Note   Note
    Your system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.
      My System SpecsSystem Spec


  7. Joined : Aug 2015
    Posts : 42
    Windows 10 Pro 64bit
       26 Aug 2015 #17

    So far, it's ok. How long should I leave it running? Can I shut down my computer later tonight? Or leave it in standby mode?
      My System SpecsSystem Spec


  8. Joined : Jun 2015
    Posts : 10,897
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       26 Aug 2015 #18

    You should run driver verifier for max 48 hours at a time, or until you get a bluescreen, which comes first.
    You can leave the pc while driver verifier is running, but do not shut your pc down!
      My System SpecsSystem Spec


  9. Joined : Aug 2015
    Posts : 42
    Windows 10 Pro 64bit
       28 Aug 2015 #19

    It's still ok..

    I've decided to do a clean install, so thanks for your help anyway.
      My System SpecsSystem Spec


  10. Joined : Jun 2015
    Posts : 10,897
    Windows 10 Pro / Windows 10 TP / Windows 8.1 Pro / Windows 7 Pro
       28 Aug 2015 #20

    If driver verifier hasn't crashed then it is most likely a hardware problem with windows 10.
    Before a clean install, would you mind to do a couple of hardware related tests?
      My System SpecsSystem Spec


 
Page 2 of 3 FirstFirst 123 LastLast


Similar Threads
Thread Forum
Bsod - page_fault_in_nonpaged_area & system_service_exception
Hello, I've just completed a upgrade install of WIndows 10 (Following a clean Windows 7 install onto a new flash drive). There have been no errors during the installation that I have been aware of, however, in the last 24 hours I have seen a...
BSOD Crashes and Debugging
BSOD page_fault_in_nonpaged_area
Got a HP 8200 Elite SFF that I've installed Windows 10 on... it's been a bumpy ride trying to clear up driver related issues but now I'm stuck... I've had a few different BSOD over the last 2 days and I'm convinced it's some driver... maybe the usb...
BSOD Crashes and Debugging
Bsod page_fault_in_nonpaged_area (fltmgr.sys)
Any help would be appreciate.32983
BSOD Crashes and Debugging
BSOD page_fault_in_nonpaged_area mcupdate_authenticamd.dll
Hi, I've been getting some BSODs lately and it intensifies. I don't really know what causes them, it seems completely random to me. I've been lurking here but didn't find anything i could use to solve my problem, so i thought i'd start a new one....
BSOD Crashes and Debugging
BSOD while upgrading to Windows 10, error C1900101-20017
Hi, I've tried 11 times to upgrade to Windows 10, but every time, no matter what I try, I am confronted with a blue-screen after the first restart in the upgrade process. Upon rebooting, I get a box pop up which tells me I have got error...
BSOD Crashes and Debugging
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 02:59.
Find Us
Twitter Facebook Google+



Windows 10 Forums