New
#1
looking to have Memory dump file looked at
hi,
i would like to have someone read the memory dump and tell me what they see as the error.
my guess being a ryzen machine it's ether ram or a device driver.
thanks,
Nathan Saunders
hi,
i would like to have someone read the memory dump and tell me what they see as the error.
my guess being a ryzen machine it's ether ram or a device driver.
thanks,
Nathan Saunders
Looks like you've only had one BSOD,
Those are both Windows Operating system files, neither the cause of the failure.Code:BugCheck 139, {3, ffff860f124addb0, ffff860f124add08, 0} *** ERROR: Module load completed but symbols could not be loaded for Wdf01000.sys *** WARNING: Unable to verify timestamp for USBXHCI.SYS *** ERROR: Module load completed but symbols could not be loaded for USBXHCI.SYS Probably caused by : USBXHCI.SYS ( USBXHCI+27c73 )
Your specs say you have 8GB DDR3 but the dump and supporting files say 4GB. Since you've only had this single BSOD, try reseating ( removing then reinstalling) the memory DIMM as sometimes a contact can become slightly corroded. If you get another then I suggest testing your memory for the full 8 passes as described below.
===================================================
Follow this tutorial: MemTest86+ - Test RAM - Windows 10 Forums
MemTest86+ is a diagnostic tool designed to test Random Access Memory (RAM) for faults. MemTest86+ will verify that:
- RAM will accept and keep random patterns of data sent to it
- There are no errors when different parts of memory try to interact
- There are no conflicts between memory addresses
Memtest86+ runs from bootable media to isolate the RAM from the system, no other components are taken into account during the test.
WarningMemTest86+ needs to run for at least 8 passes to be anywhere near conclusive, anything less will not give a complete analysis of the RAM.
If you are asked to run MemTest86+ by a Ten Forums member make sure you run the full 8 passes for conclusive results. If you run less than 8 passes you will be asked to run it again.
NoteMemTest86+ has been known to discover errors in RAM in later passes than the eighth pass. This is for information only; if you feel there is a definite problem with the RAM and 8 passes have shown no errors feel free to continue for longer.
Running 8 passes of MemTest86+ is a long and drawn out exercise and the more RAM you have the longer it will take. It's recommended to run MemTest86+ just before you go to bed and leave it overnight.
Take a picture when done and post in the forum please.
so the specs in my signature is a different machine,
the specs for the machine with the issues is
ryzen 7 1700x with 16 GB of ddr4 win 10 64 bit
--
and it sounds like i should reinstall the usb driver right?
also i have disabled the reboot on BSOD and disabed USB selective suspend based on this:
BSOD issue with USBXHCI.SYS - Windows 10 Forums
thanks,
Nathan Saunders
Yes, 16GB in DIMM1, sorry, I misread the dump BIOS data.
Reinstalling the USB drivers wouldn't hurt but testing the ram would also be a good idea.
16GB is going to take a long time, so running over night is the best way to go. I would expect it to take 12 hours or more to get 8 full passes.
If that doesn't show any problems then I would suggest enabling Driver Verifier to see if it can shake out any driver problems, as follows:
===================================================
Driver Verifier is a diagnostic tool built into Windows 10, it is designed to verify both native Microsoft drivers and third party drivers. Driver Verifier's verification process involves putting heavy stress on drivers with the intention of making bad, outdated, incompatible or misbehaving drivers fail. The required result is a BSOD (Blue Screen of Death) which will generate a crash dump for debugging purposes.
Machines exposed to Driver Verifier will run very sluggishly due to the stress being applied to the drivers.
Driver Verifier - Enable and Disable in Windows 10
Pay close attention to PART TWO and make sure the correct boxes are checked.
Warning:
It is not advised to run Driver Verifier for more than 48 hours at a time. Disable Driver Verifier after 48 hours or after receiving a BSOD, whichever happens soonest.
Always create a Restore Point prior to enabling Driver Verifier.
What we're looking for is a verifier generated BSOD with a mini dump that will tell us what driver caused it. If you get a BSOD, rerun dm_log_collector and upload the resulting zip file.
Rats, can't test right now. Not able to boot into EFI setup for some reason. Seems to be a comon problem for Lenovo computers sooner or later. I'll see if I can fix it and test then. Meanwhile, give it a shot. If you look at the flash drive memtest86+ creates, it has a EFI folder on it so I believe it will boot in EFI mode okay.