BSOD's related to memory / drivers, increasing in frequency

Page 8 of 16 FirstFirst ... 678910 ... LastLast
  1.    #71

    Several system restore points are available but I cannot proceed, the status shows "You must enable system protection on this drive".

    Startup repair failed. I am able to open the command prompt.
      My ComputerSystem Spec


  2. Posts : 25,063
    windows 10 professional version 1607 build 14393.969 64 bit
       #72

    With command prompt open use a camera or smart phone camera to take pictures and post images of the commands and results into the thread.

    Type all of these commands. Steps that are not commands to type are in parenthesis.

    1) bcdedit /enum
    2) bcdedit | find "osdevice"
    3) c:
    4) dir
    5) d:
    6) dir
    7) diskpart
    8) list disk
    9) list volume
    10) select disk 0
    11) detail disk
    12) list partition
    13) select partition 1
    14) detail partition
    15) select partition 2
    16) detail partition
    17) select partition 3
    18) detail partition
    19) select partition 4
    20) detail partition
    21) if there are any additional partitions continue in a similar fashion
    22) exit
    23) chkdsk /r
    (This may take many hours and typically displays ETA.)
    24) (reboot as necessary)
    25) reopen command prompt > administrator: X:\windows\system32/cmd.exe > X:\sources>
    (Type these commands: )
    26) bootrec /fixmbr
    27) bootrec /fixboot
    28) bootrec /scanos
    29) bootrec /rebuildbcd
    30) (reboot)

    Please make sure to take pictures and post images of the results for each command and result into the thread.


    The backup plan is boot rescue.
    Find a flash drive that you can format.
    Windows 10 Recovery Tools - Bootable Rescue Disk - Windows 10 Forums
    If a backup image were available:
    Backup and Restore with Macrium Reflect | Windows 10 Tutorials
      My ComputerSystem Spec

  3.    #73

    At step 10: should I select the system drive? Volume 0 is showing as one of my secondary HDD's. The system drive is volume 2.
      My ComputerSystem Spec


  4. Posts : 25,063
    windows 10 professional version 1607 build 14393.969 64 bit
       #74

    step 10 is using disk not volume
    did you mean disk 1 instead of disk 0?
    Display the info for disk 0 and disk 1 then in the latter commands.
      My ComputerSystem Spec


  5. Posts : 25,063
    windows 10 professional version 1607 build 14393.969 64 bit
       #75

    In approximately one hour I will return but must run an errand now.
    See what you can do with the above commands and post images into the the thread.
      My ComputerSystem Spec

  6.    #76

    Sorry, disk 0 is a backup and disk 1 is the system drive. Should I still start with disk 0?
      My ComputerSystem Spec


  7. Posts : 25,063
    windows 10 professional version 1607 build 14393.969 64 bit
       #77

    For each disk run these commands:
    select disk 0
    detail disk
    select disk 1
    detail disk
    select disk 2
    detail disk
    select disk 3
    detail disk
    For the applicable disk with the volumes and partitions run the subsequent commands so that all of the partition information is displayed.
      My ComputerSystem Spec

  8.    #78

    When I run chkdsk /R:

    The type of the file system is NTFS.
    Cannot lock current drive.

    Chkdsk cannot run because the volume is in use by another
    process. Chkdsk may run if this volume is dismounted first.
    ALL OPENED HANDLES TO THIS VOLUME WOULD THEN BE INVALID.
    Would you like to force a dismount on this volume? (Y/N)
      My ComputerSystem Spec


  9. Posts : 25,063
    windows 10 professional version 1607 build 14393.969 64 bit
       #79

    yes
    reboot as needed
      My ComputerSystem Spec


  10. Posts : 25,063
    windows 10 professional version 1607 build 14393.969 64 bit
       #80

    In post #2 which steps were skipped?

    Had a Macrium backup image never been made?
    Had a restore point never been made?
    Had the BIOS been reset?
    Any other steps skipped in post #2 or other posts?

    Were restore points at any time manually turned on or off?
      My ComputerSystem Spec


 
Page 8 of 16 FirstFirst ... 678910 ... LastLast

Related Threads
BSOD Occurring with increasing frequency in BSOD Crashes and Debugging
Hope someone will be able to decipher what the issue is, I have looked at dump files but they all seem to point to: Analysis Inconclusive :confused: Please see attached. Kind regards, Rob
Started a month ago went 3 weeks no BSOD about 3 days ago 2 in one week since then it has been every hour or so while playing a game called eve online. Although I cant confirm this to be contributing to the failure (as I mostly am playing this...
we have windows 10 of a new hp pc prodesk 400 g3 mt business pc. we cannot identify the problem.. we used the hp drivers software and fully updated windows 10 and the latest drivers. Please recommend troubleshooting steps what is causing the...
BSOD 32 bit memory related in BSOD Crashes and Debugging
I'm getting a BSOD predictably, but not every single time. I'm using an audio recording program - Sonar Platinum. It has a 32 bit and a 64 bit version. I'm in the process of shifting over to 64 bit, yet sometime I still need to open a project in...
Since up loading to 10, I have had a few BODS some with or without a warning message that there is insufficient memory space, but memory diagnostics show no issues. Here are the dumps from two of the latest incidents: 29213 29212
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 17:06.
Find Us