BSOD on print preview, PAGE_FAULT_IN_NONPAGED_AREA, cdd.dll

  1. Posts : 3
    Windows 10 Pro 64-bit
       01 Mar 2018 #1

    BSOD on print preview, PAGE_FAULT_IN_NONPAGED_AREA, cdd.dll

    While inside an Autodesk Revit 2017 file the computer will crash every time we have a specific file open and we try to do a print preview. BSOD occurs shortly after it generates the preview.

    What Failed: cdd.dll
    (image attached with BSOD screen)

    1. BSOD only occurs in 1 specific Revit file when generating a print preview. (doesn't matter which printer is selected for use, error still occurs).
    2. BSOD does not occur when we are on a different computer generating a print preview on the same file that continuously crashes the computer I am posting about.
    3. BSOD does not occur on the offending computer when we are in other Revit files and are generating a print preview.

    Any help is greatly appreciated. Let me know if there is any other information is needed and I will be happy to supply what I can.
    Attached Thumbnails Attached Thumbnails BSOD.JPG  
    BSOD on print preview, PAGE_FAULT_IN_NONPAGED_AREA, cdd.dll Attached Files
      My ComputerSystem Spec

  2. Posts : 3
    Windows 10 Pro 64-bit
    Thread Starter
       02 Mar 2018 #2

    Just in case it helps I also used the Log Collector V2 Beta to collect info. Please see attached.
    BSOD on print preview, PAGE_FAULT_IN_NONPAGED_AREA, cdd.dll Attached Files
      My ComputerSystem Spec

  3. Ztruker's Avatar
    Posts : 6,750
    Windows 10 Pro X64 1809 17763.134
       03 Mar 2018 #3

    The first 4 dumps point to cdd.dll as the cause which is unlikely as it's a system file that has not been changed in a while. The lasty says memory_corruption in win32k.sys, again unlikely.

    You have 64GB of RAM so I would start by removing half the ram and running for awhile and see if a BSOD occurs. If not, swap theinstalled and removed ran and run some more to see if it occurs. If it does then one of the two 16GB DIMMS currently install is defective. You can swap them out ione at a time with the removed DIMMs to try to find the bad one or you can run memtest76+ as follows:
    Follow this tutorial: MemTest86+ - Test RAM - Windows 10 Forums

    MemTest86+ is a diagnostic tool designed to test Random Access Memory (RAM) for faults. MemTest86+ will verify that:

    • RAM will accept and keep random patterns of data sent to it
    • There are no errors when different parts of memory try to interact
    • There are no conflicts between memory addresses

    Memtest86+ runs from bootable media to isolate the RAM from the system, no other components are taken into account during the test.

    warning   Warning
    MemTest86+ needs to run for at least 8 passes to be anywhere near conclusive, anything less will not give a complete analysis of the RAM.

    If you are asked to run MemTest86+ by a Ten Forums member make sure you run the full 8 passes for conclusive results. If you run less than 8 passes you will be asked to run it again.

    Note   Note
    MemTest86+ has been known to discover errors in RAM in later passes than the eighth pass. This is for information only; if you feel there is a definite problem with the RAM and 8 passes have shown no errors feel free to continue for longer.

    Running 8 passes of MemTest86+ is a long and drawn out exercise and the more RAM you have the longer it will take. It's recommended to run MemTest86+ just before you go to bed and leave it overnight.

    Take a picture when done and post in the forum please.

    If removing ram doesn't help then I'd try Driver Verifier:
    Driver Verifier
    is a diagnostic tool built into Windows 10, it is designed to verify both native Microsoft drivers and third party drivers. Driver Verifier's verification process involves putting heavy stress on drivers with the intention of making bad, outdated, incompatible or misbehaving drivers fail. The required result is a BSOD (Blue Screen of Death) which will generate a crash dump for debugging purposes.
    Machines exposed to Driver Verifier will run very sluggishly due to the stress being applied to the drivers.

    Driver Verifier - Enable and Disable in Windows 10

    Pay close attention to PART TWO and make sure the correct boxes are checked.

    It is not advised to run Driver Verifier for more than 48 hours at a time. Disable Driver Verifier after 48 hours or after receiving a BSOD, whichever happens soonest.

    Always create a Restore Point prior to enabling Driver Verifier.

    What we're looking for is a verifier generated BSOD with a mini dump that will tell us what driver caused it. If you get a BSOD, rerun the V2 beta log collector and upload the resulting zip file.

      My ComputersSystem Spec

  4. Posts : 3
    Windows 10 Pro 64-bit
    Thread Starter
       05 Mar 2018 #4

    Rich thanks for the response. I'll check to see if it still crashes on the revit file with different combinations or RAM as suggested. It has been unfailing to crash when on this one particular (large) file. That may allow me to narrow down the RAM sticks pretty quickly. I'll post the results as soon as I am able to.
    Thanks for your help and suggestions.
      My ComputerSystem Spec

  5. Ztruker's Avatar
    Posts : 6,750
    Windows 10 Pro X64 1809 17763.134
       07 Mar 2018 #5

    Has to be something local to your system since the file works okay on a different system, so as you say, it makes an excellent test vehicle.
      My ComputersSystem Spec


Related Threads
So I was trying to launch this game called Just Cause 3 on steam and it was about to load until it CTD with "Just Cause 3 has stopped working" and then I got that BSOD right after. Please help I have no idea why this is happening. If any additional...
Solved Bsod page_fault_in_nonpaged_area in BSOD Crashes and Debugging
Hi, I'm getting bsod at the very start of the laptop. Seems like the update of intel wifi and bluetooth driver caused it (using intel update utility). I used dm_log collector, it seems to run ok but it doesn't create any zip file (it was run...
OK, this one is a twist on a very often reported problem on these forums: Internet Explorer 11 will not print and just shows an empty print preview page. (Edge works/prints fine). However in this case I know what caused the issue but not how...
Bsod page_fault_in_nonpaged_area in BSOD Crashes and Debugging
Hey, I've been getting a BSOD often on my laptop ever since I updated to Windows 10. I don't think it's caused by a certain program I run because they seem to happen pretty randomly. I'm not too tech savvy when it comes to these types of things but...
BSOD page_fault_in_nonpaged_area in BSOD Crashes and Debugging
Got a HP 8200 Elite SFF that I've installed Windows 10 on... it's been a bumpy ride trying to clear up driver related issues but now I'm stuck... I've had a few different BSOD over the last 2 days and I'm convinced it's some driver... maybe the usb...
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 21:40.
Find Us