Page 3 of 3 FirstFirst 123
  1.    17 Sep 2015 #21
    Join Date : Sep 2015
    Posts : 23
    Windows 10

    Thank you for the warnings AveYo!
    So I've connected the sub-woofer as you told me to, I've tried both the first and second method. The sub-woofer still works as a center speaker, not a sub-woofer in the Realtek HD Audio Manager software. There is still no option to change the center/ sub-woofer speaker output. That option is apparently normally there, no clue why it's not on my software although I guess it has something to do with my motherboard.

    If there's no work-around I'll definitely give up on it and use my piece of trash speakers in a stereo setup instead! (:

    Edit; If I use the red cable instead (right) of the white one (left) as you told me to, and turn the volume up high enough you can hear the test tune go through the sub-woofer as intended, it's just really low. In other words It's recognized as a sub-woofer in the Realtek HD Audio Manager software, as long as I use the red cable to right amp input instead of white cable to left amp input.
    Edit2; If I turn off the bridged mode on the back of the amp the volume suddenly gets louder? Not sure if this is how it's supposed to react, or if it's still acting like a center speaker.
    Last edited by Hauksort; 17 Sep 2015 at 05:41.
      My System SpecsSystem Spec

  2.    17 Sep 2015 #22
    Join Date : Aug 2015
    Posts : 120
    Windows 10 (duh)

    That's why I've used red for the unknown ohm subwoofer part. It makes quite a difference if it's 8ohm or if it's below that as bridged mono mode requires 8ohm or higher, on any amp I've seen. From the pictures posted I can see it's mentioned just under the red outputs. I don't see a bridge turn switch, but if there is one, it should have some warnings as to what you can connect in bridged mode. Most likely the subwoofer is below 8ohm (4?) so it's unsupported, cannot gain x2 output power. Stop connecting it to the two red outputs, instead use a normal black+red pair.

    Anyway, there is no good choice when it comes to pairing 3 speakers to a single amp. Most, if not all 2.1 commercial products are actually 2 ams in one.

    Best bet is to use the current amp for the 6ohm speakers in stereo mode, and get another cheap mono amp for the subwoofer.

    About realtek gui:
    - some options appear only under 7.1 or 5.1 mode.
    - enable bass management and full-range options.
    - disable auto popup dialog under Connector Settings, then use connector retasking option when right-clicking output panel icons
      My System SpecsSystem Spec

  3.    17 Sep 2015 #23
    Join Date : Sep 2015
    Posts : 23
    Windows 10

    Thank you again! I think I got all information I need or more, so I'll mark the thread as solved. (:
      My System SpecsSystem Spec

Page 3 of 3 FirstFirst 123

Similar Threads
Thread Forum
Windows 8.1 computer not showing in network on Windows 10 10049 system
I have 3 computers on my network Windows 8.1 Pro X64 - named Desktop Windows 7 Pro X64 - named Webserver Windows 10 TP X64 build 10049 - named Laptop I can see all 3 computers on my network from Desktop and Webserver. I can see Webserver...
Network and Sharing
Solved Only 2 speakers work out of 6 - Logitech x350 Audio System
Hello, I registered today to seek for a solution to this annoying problem. I have the Logitech x350 Audio system, with 6 speakers and one sub-woofer and they worked pretty well on my former OS, Windows 8.1 x64. Now I am currently using W10 and...
Drivers and Hardware
Accidentally turned off the computer while in system restore
So I was doing a system restore on my newly upgraded Windows 10. It was stuck at 46% so I restarted it (which was a stupid thing I know). After that the laptop won't go beyond the black screen. Whenever I boot the laptop the lenovo logo appears and...
General Support
Solved Windows 10 Home. Disable this file came from another computer.
I am just going to say up front that I don't have the Pro version of Windows 10 so I have no Group Policy Editor otherwise I would have fixed this problem in less than a minute instead of wasting over a hour trying to fix this. I want to disable...
General Support
Solved When will Win 10 Home download to my Win 7 computer?
If it actually happens before July 29 (not likely) how can I determine if the Win 10 Home install file(s) have downloaded to my Win 7 computer? If its after July 29 I expect I'll get some sort of notification and option to install.
General Support
Our Sites
Site Links
About Us
Windows 10 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 10" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 13:36.
Find Us
Twitter Facebook Google+

Windows 10 Forums